Adjustment of the Artificial Feel Unit [PW11]

TASK 76-11-00-820-804-A
Adjustment of the Artificial Feel Unit

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 2M (6 FT)
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)
98D76103000002	1	MEASURE,LOAD-THROTTLE LEVER

B. Consumable Materials

REFERENCE	DESIGNATION
No specific	corrosion-resistant steel lockwire 0.8 mm dia (0.032 in.)

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
811

D. Referenced Information

REFERENCE	DESIGNATION
Adjustment of the Artificial Feel Unit

3. Job Set-up
Subtask 76-11-00-941-065-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) Put a WARNING NOTICE(S) in position in the cockpit to tell persons not to move:

The throttle control levers
The slat and flap control lever.

Subtask 76-11-00-865-072-A ** ON A/C NOT FOR ALL

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B08
** ON A/C NOT FOR ALL
49VU	ENGINE/1 AND 2/IGN/SYS A	1JH	A03
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B03
** ON A/C NOT FOR ALL
121VU	ENGINE/IGN/ENG2/SYS B	3JH2	P42
121VU	ENGINE/IGN/ENG1/SYS B	3JH1	P41
121VU	FLIGHT CONTROLS/SEC3/SPLY	21CE3	Q19
121VU	FLIGHT CONTROLS/SEC2/SPLY	21CE2	Q18

Subtask 76-11-00-480-054-A ** ON A/C NOT FOR ALL

C. Install the 98D76103000002 MEASURE,LOAD-THROTTLE LEVER on the throttle control levers.

Subtask 76-11-00-941-066-A ** ON A/C NOT FOR ALL

D. Put an ACCESS PLATFORM 2M (6 FT) in position below the forward avionics compartment.

Subtask 76-11-00-010-062-A ** ON A/C NOT FOR ALL

E. Open access door 811.

4. Procedure
Subtask 76-11-00-820-066-A ** ON A/C NOT FOR ALL

A. Adjustment of the Artificial Feel Unit
(1) Loosen the three screws (3). Remove the guard (7).
(2) Remove the lockwire.

WARNING: USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

(a) Cut and remove the lockwire from the lock nut (6). Loosen the lock nut.
(3) Hold the adjusting rod (5) then turn the nut (4) to get a load of between 0.85 daN (1.91 lbf) and 1.05 daN (2.36 lbf) handle on IDLE (0°) and between 0.45 daN (1.01 lbf) and 0.65 daN (1.46 lbf) handle on TOGA (45°) on the related throttle control lever.

NOTE: Measure this value in the IDLE STOP/MAX CLIMB range. Do not measure this value at the detent points where the load increases suddenly.

(4) Tighten the lock nut (6) to block the adjustment system. Measure the load again to make sure that it is the same.
(5) Safety the lock nut (6) with corrosion-resistant steel lockwire 0.8 mm dia (0.032 in.).
(6) Install the guard (7). Tighten the three screws (3).
(7) Remove the lockwire.

(a) Cut and remove the lockwire from the lock nut (2). Loosen the lock nut.
(8) Turn the adjustment screw (1) to get a break-out force of 2.5 +0.1 daN or -0 daN (5.62 +0.22 lbf or +0.00 lbf) when you go through the MAX CLIMB detent point (the first detent point that you feel when you move the lever forward).

NOTE: This hard point includes the load measured in step (3).

(9) Block the adjustment system. Measure the load again to make sure that it is the same as the value given in step (8).
(10) Safety the lock nut.

(a) Safety the lock nut (2) with corrosion-resistant steel lockwire 0.8 mm dia (0.032 in.).

5. Close-up
Subtask 76-11-00-080-054-A ** ON A/C NOT FOR ALL

A. Remove the 98D76103000002 MEASURE,LOAD-THROTTLE LEVER from the throttle control levers.

Subtask 76-11-00-865-073-A ** ON A/C NOT FOR ALL

B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B08
** ON A/C NOT FOR ALL
49VU	ENGINE/1 AND 2/IGN/SYS A	1JH	A03
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B03
** ON A/C NOT FOR ALL
121VU	ENGINE/IGN/ENG2/SYS B	3JH2	P42
121VU	ENGINE/IGN/ENG1/SYS B	3JH1	P41
121VU	FLIGHT CONTROLS/SEC3/SPLY	21CE3	Q19
121VU	FLIGHT CONTROLS/SEC2/SPLY	21CE2	Q18

Subtask 76-11-00-410-062-A ** ON A/C NOT FOR ALL

C. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close access door 811.
(3) Remove the access platform(s).
(4) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 13:09:31 UTC