DOC AIRBUS | AMM A320FGeneral Visual Inspection of the Throttle Control System [IAE]
TASK 76-11-00-210-040-A
General Visual Inspection of the Throttle Control System
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 76-11-00-941-050-A ** ON A/C NOT FOR ALL
Subtask 76-11-00-210-050-A ** ON A/C NOT FOR ALL
Subtask 76-11-00-410-050-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 03:15:43 UTC
General Visual Inspection of the Throttle Control System
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE |
| No specific | AR | LIGHT SOURCE - INSPECTION |
| No specific | AR | MIRROR - INSPECTION |
| No specific | AR | WARNING NOTICE(S) |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 811 |
| REFERENCE | DESIGNATION |
|---|---|
Throttle Control SystemSubtask 76-11-00-941-050-A ** ON A/C NOT FOR ALL
A. Safety Precautions
(1) Make sure that the throttle control levers are set to idle (0 degrees TLA).
(2) Put a WARNING NOTICE(S) in the cockpit to tell persons not to move:
Subtask 76-11-00-010-050-A ** ON A/C NOT FOR ALL 4. Procedure(1) Make sure that the throttle control levers are set to idle (0 degrees TLA).
(2) Put a WARNING NOTICE(S) in the cockpit to tell persons not to move:
- the throttle control levers
- the slat and flaps control levers.
Subtask 76-11-00-210-050-A ** ON A/C NOT FOR ALL
A. Inspection of Trottle Control System.
(1) Visually examine the throttle control unit (4).
(a) Make sure that the mount nuts which attach the throttle control unit (4) to its support are not loose.
(b) Make sure that the four electrical connectors (5) are tighten.
(2) Visually examine the lower rods (3).
(a) Make sure that the upper and lower attachments of the rods are lockwired.
(b) Make sure that the rods can move freely on their bearings.
(3) Visually examine the upper rods (2).
(a) Repeat the same inspection as for the lower rods. For the upper attachment of the rods, use an LIGHT SOURCE - INSPECTION and an MIRROR - INSPECTION.
(4) Visually examine the bellcrank (6) of the throttle control lever.
(a) Make sure that there is no foreign object in the system and in its area.
(5) Visually examine the throttle control levers (1) in the cockpit for good condition.
(a) Make sure that there are no unwanted object which can prevent the full travel of the levers.
5. Close-up(1) Visually examine the throttle control unit (4).
(a) Make sure that the mount nuts which attach the throttle control unit (4) to its support are not loose.
(b) Make sure that the four electrical connectors (5) are tighten.
(2) Visually examine the lower rods (3).
(a) Make sure that the upper and lower attachments of the rods are lockwired.
(b) Make sure that the rods can move freely on their bearings.
(3) Visually examine the upper rods (2).
(a) Repeat the same inspection as for the lower rods. For the upper attachment of the rods, use an LIGHT SOURCE - INSPECTION and an MIRROR - INSPECTION.
(4) Visually examine the bellcrank (6) of the throttle control lever.
(a) Make sure that there is no foreign object in the system and in its area.
(5) Visually examine the throttle control levers (1) in the cockpit for good condition.
(a) Make sure that there are no unwanted object which can prevent the full travel of the levers.
Subtask 76-11-00-410-050-A ** ON A/C NOT FOR ALL
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the access door 811.
(3) Remove the access platform(s).
(4) Remove the WARNING NOTICE(S).
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the access door 811.
(3) Remove the access platform(s).
(4) Remove the WARNING NOTICE(S).