Replacement of the Air Tubing (P2.5) on Engine 1(2) [IAE]

TASK 73-22-49-960-801-A
Replacement of the Air Tubing (P2.5) on Engine 1(2)

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 150 and 142 lbf.in (1.70 and 1.60 m.daN )

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.V02-126)	lockwire

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR

D. Referenced Information

REFERENCE	DESIGNATION
TASK 70-23-11-911-013-A	General Torque Tightening Techniques
TASK 71-13-00-010-010-A	Opening of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-410-010-A	Closing of the Fan Cowls 437AL(447AL),438AR(448AR)
P2.5 Air Tubing
Replacement of the Air Tubing (P2.5)

3. Job Set-up
Subtask 73-22-49-941-056-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on ENG panel 115VU:
(a) Put a WARNING NOTICE(S) in position to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than five minutes before you do this procedure.
(3) On overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) in position to tell persons not to energize FADEC 1(2).

Subtask 73-22-49-010-055-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Open the fan cowls (Ref. AMM TASK 71-13-00-010-010):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR

4. Procedure
Subtask 73-22-49-020-061-A ** ON A/C NOT FOR ALL

A. Disconnect the Flexible Hose
(1) Removal of the lockwire

WARNING: USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

(a) Cut and discard the lockwire from the flexible hose (4) connector.
(2) Disconnect the flexible hose (4) from the union (3).

NOTE: Do not remove the union (3) from the EEC (1).

(3) Disconnect the flexible hose (4) from pipe (10) without removing nut (20).

Subtask 73-22-49-420-059-A ** ON A/C NOT FOR ALL

B. Connect the Flexible Hose

NOTE: Make sure that all the tubes, which make up the air tubing, are correctly connected. Joints that leak can let moisture into the line and cause P2.5 problems.

(1) Make sure that the union (3) has no debris or contamination.
(2) Install the flexible hose (4) onto piping (10).
(3) TORQUE the connector to between 150 and 142 lbf.in (1.70 and 1.60 m.daN )

(Ref. AMM TASK 70-23-11-911-013).
(4) Safety the connector

(a) Safety the connector with lockwire (Material No.V02-126) .
(5) Install the flexible hose (4) onto union (3).
(6) TORQUE the connector to between 150 and 142 lbf.in (1.70 and 1.60 m.daN )

(Ref. AMM TASK 70-23-11-911-013).
(7) Safety the connector

(a) Safety the connector with lockwire (Material No.V02-126) .

5. Close-up
Subtask 73-22-49-410-054-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the fan cowls (Ref. AMM TASK 71-13-00-410-010):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(3) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 03:01:13 UTC