DOC AIRBUS | AMM A320FRemoval of the P2/T2 Sensor [IAE]
TASK 73-22-11-000-010-A
Removal of the P2/T2 Sensor
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Referenced Information
3. Job Set-up
Subtask 73-22-11-941-050-A ** ON A/C NOT FOR ALL
Subtask 73-22-11-010-050-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 03:00:45 UTC
Removal of the P2/T2 Sensor
FIN: 4014KS ** ON A/C NOT FOR ALL
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | ACCESS PLATFORM 2M (6 FT) |
| No specific | AR | COVER - BLANKING |
| No specific | AR | WARNING NOTICE(S) |
| REFERENCE | DESIGNATION |
|---|---|
P2/T2 SensorSubtask 73-22-11-941-050-A ** ON A/C NOT FOR ALL
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
4. Procedure(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
Subtask 73-22-11-010-050-A ** ON A/C NOT FOR ALL
A. Get Access
(1) Put the ACCESS PLATFORM 2M (6 FT) in position to give access to the air intake cowl.
(2) Remove the 18 bolts (7). Remove the access panel (6).
(a) Disconnect the P2 tube end connectors and remove the tube (12).
Subtask 73-22-11-020-050-A ** ON A/C NOT FOR ALL (1) Put the ACCESS PLATFORM 2M (6 FT) in position to give access to the air intake cowl.
(2) Remove the 18 bolts (7). Remove the access panel (6).
(a) Disconnect the P2 tube end connectors and remove the tube (12).
B. Disconnect the electrical connectors
(1) Disconnect the electrical connectors 4014KS-A (15) and 4014KS-B (14) from the sensor
(2) Remove the sensor
(a) Make a note of the position of the bonding clamp (4).
(b) Remove the nut (3) and the bolt (5) from the bonding clamp (4). Remove the bonding clamp (4) from the P2/T2 sensor (8).
(c) Cut and discard the lockwire from the six bolts (2).
(d) Remove the bolts (2), the washers (1) and the clip mounting bracket (9).
(e) Remove the P2/T2 sensor (8).
Subtask 73-22-11-010-051-A ** ON A/C NOT FOR ALL (1) Disconnect the electrical connectors 4014KS-A (15) and 4014KS-B (14) from the sensor
(2) Remove the sensor
(a) Make a note of the position of the bonding clamp (4).
(b) Remove the nut (3) and the bolt (5) from the bonding clamp (4). Remove the bonding clamp (4) from the P2/T2 sensor (8).
(c) Cut and discard the lockwire from the six bolts (2).
(d) Remove the bolts (2), the washers (1) and the clip mounting bracket (9).
(e) Remove the P2/T2 sensor (8).
C. Remove the union (10) from the sensor and discard the packing (11).
Subtask 73-22-11-620-050-A ** ON A/C NOT FOR ALL D. Put the applicable COVER - BLANKING on all of the openings.