Removal of the Rigid Fuel Tube, Aircraft to the LP Pump [IAE]

TASK 73-11-47-000-010-A
Removal of the Rigid Fuel Tube, Aircraft to the LP Pump

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.

WARNING: BE CAREFUL NOT TO GET AIRCRAFT FUEL IN YOUR MOUTH OR IN YOUR EYES. IF YOU GET FUEL ON YOUR SKIN OR ON YOUR CLOTHES, FLUSH IT IMMEDIATELY WITH WATER. IF NECESSARY, GET MEDICAL HELP. AIRCRAFT FUEL IS POISONOUS.

CAUTION: DO NOT LET ENGINE FUEL OR OIL FALL ON THE ENGINE. UNWANTED FUEL OR OIL MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. THE FUEL OR OIL CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.

CAUTION: DO NOT PUT FUEL THAT HAS BEEN DRAINED FROM THE ENGINE BACK IN TO THE FUEL SYSTEM.

FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 1M(3 FT)
No specific	AR	CAP - BLANKING
No specific	AR	CONTAINER 5 L (1.32 USGAL)
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-010-A	Opening of the Fan Cowls 437AL(447AL),438AR(448AR)
Rigid Fuel Tubes

3. Job Set-up
Subtask 73-11-47-941-051-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

Subtask 73-11-47-010-051-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Open the fan cowls. (Ref. AMM TASK 71-13-00-010-010)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Put the ACCESS PLATFORM 1M(3 FT) in position

4. Procedure
Subtask 73-11-47-020-050-A ** ON A/C NOT FOR ALL

A. Removal of the rigid fuel tube, aircraft to the LP pump

Rigid Fuel Tubes ** ON A/C NOT FOR ALL

(1) Do the steps which follow :

CAUTION: HOLD THE UNION DURING THE DISCONNECT PROCEDURE TO PREVENT DAMAGE TO THE FLEXIBLE HOSE.

(a) Loosen the bolts (2) and the nuts (4)
(b) Loosen the fuel tubes (6) and (7) at the unions on the mounting bracket and drain the fuel into the CONTAINER 5 L (1.32 USGAL)
(c) Loosen the nut (5) at the union on the mounting bracket.

SBE73-0219

(d) Removal of the lockwire

WARNING: USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

1 Cut, remove and discard the lockwire that attaches the tube assembly (16).
(e) Loosen the tube assembly (16).

END OF SBE73-0219

SBE73-0224

SBE73-0235

(f) Removal of the lockwire

1 Cut, remove and discard the lockwire that attaches the blanking plug (17).
(g) Loosen the blanking plug (17).

END OF SBE73-0224

END OF SBE73-0235

(2) Remove the aircraft to the LP pump fuel tube
(a) Remove the bolts (9) and the washers (11).
(b) Remove the bolts (12) and disconnect the fuel tube (6) from the LP fuel pump. Drain the fuel into the clean CONTAINER 5 L (1.32 USGAL)

CAUTION: HOLD THE UNION DURING THE DISCONNECT PROCEDURE TO PREVENT DAMAGE TO THE FLEXIBLE HOSE.

(c) Disconnection of the tube

SBE73-0219

1 Disconnect the tube assembly (16) from the fuel tube (6).

END OF SBE73-0219

SBE73-0224

SBE73-0235

2 Disconnect the blanking plug (17) from the fuel tube (6).

END OF SBE73-0224

END OF SBE73-0235

3 Disconnect the tube (6) from the union on the mounting bracket and remove the tube from the engine.
(d) Remove and discard the sealing ring (13) from the tube flange.
(3) Remove the clips (10) from the tube and keep them for the installation of the replacement tube.

Subtask 73-11-47-620-050-A ** ON A/C NOT FOR ALL

B. Put the applicable CAP - BLANKING on all the openings.

[Rev.10 from 2021] 2026.04.01 13:06:01 UTC