DOC AIRBUS | AMM A320FInstallation of the Fuel Filter Element [CFMB]
TASK 73-11-10-400-004-A
Installation of the Fuel Filter Element
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Expendable Parts
E. Referenced Information
3. Job Set-up
Subtask 73-11-10-860-052-A ** ON A/C NOT FOR ALL
Subtask 73-11-10-420-059-A ** ON A/C NOT FOR ALL
Subtask 73-11-10-410-063-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 02:57:30 UTC
Installation of the Fuel Filter Element
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.CP1039) | acetone |
| (Material No.CP1041) | isopropyl alcohol |
| (Material No.CP2101) | graphite grease |
| (Material No.CP5070) | vaseline |
| (Material No.CP5074) | de-aromatized petroleum |
| (Material No.CP8001) | SAFETY WIRE 0.032 in. (0.8 mm) dia. |
| (Material No.CP8002) | SAFETY WIRE 0.032 in. (0.8 mm) dia |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| FOR [1000EM1] (ENGINE-1) | |
| 437AL, 438AR | |
| FOR [1000EM2] (ENGINE-2) | |
| 447AL, 448AR | |
| FIG.ITEM | DESIGNATION | IPC-CSN |
|---|---|---|
| 80 | O-RING | AIPC 73-11-10-01-290 |
| 90 | O-RING | AIPC 73-11-10-01-310 |
| 20 | FUEL FILTER ELEMENT | AIPC 73-11-10-01-340 |
| 10 | O-RING | AIPC 73-11-10-01-350 |
| 30 | O-RING | AIPC 73-11-10-01-350 |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 71-00-00-710-006-B | Minimum Idle Check |
| TASK 71-13-00-010-040-B | Opening of the Fan Cowl Doors |
| TASK 71-13-00-410-040-B | Closing of the Fan Cowl Doors |
Fuel Filter ElementSubtask 73-11-10-860-052-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
Subtask 73-11-10-010-069-A ** ON A/C NOT FOR ALL (1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
B. Make sure that the fan cowl doors are open: (Ref. AMM TASK 71-13-00-010-040)
(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR
4. Procedure(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR
Subtask 73-11-10-420-059-A ** ON A/C NOT FOR ALL
A. Not applicable
PRE CFM SB 73-A0062
PRE CFM SB 73-0055
Subtask 73-11-10-420-068-A ** ON A/C NOT FOR ALL PRE CFM SB 73-A0062
PRE CFM SB 73-0055
B. Install the Fuel Filter Element
POST CFM SB 73-0055
Make sure that the wave spring and retaining ring are correctly installed on the inner boss of the fuel filter cover (40).
PRE CFM SB 73-0107
(b) Install the new AIPC 73-11-10-01-350 O-RING (10) and AIPC 73-11-10-01-350 O-RING (30) in the related groove of the new AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) located at both ends. Soak the new O'rings with engine fuel and slightly lubricate the new O-rings with vaseline (Material No.CP5070) .
END OF PRE CFM SB 73-0107
POST CFM SB 73-0107
(c) Soak the new O'rings located at both ends of the AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) with engine fuel and slightly lubricate the new O'rings with vaseline (Material No.CP5070) .
END OF CFM SB 73-0107
(d) Install the new AIPC 73-11-10-01-310 O-RING (90), in the related groove of the fuel filter cover (40), soak the new O-ring with engine fuel and lubricate it with vaseline (Material No.CP5070) .
(e) Carefully install the fuel filter element (20) into the filter cover (40).
(f) Visually inspect through the fuel filter element (20) that the packing O-ring (30) has not released from its groove and check that the filter element does not move.
(i) Install the bolts (100) as follows:
2 Install the 6 bolts (100), the 6 washers (110), the 6 self-aligning washers (130) and nuts (120) to obey the assembly configuration.
(j) Engage the bolt freely by hand (hold the bolt head with fingers, no tool is permitted) and rotate for two complete turns minimum (it should not be possible to fully hand tighten bolts).
(k) Torque the bolts (100).
.
(l) Unscrew the 6 bolts and TORQUE them again to between 80 and 70 lbf.in (0.90 and 0.79 m.daN )
(m) Install a new AIPC 73-11-10-01-290 O-RING (80), soak the new O-ring with engine fuel and lubricate it with vaseline (Material No.CP5070) , on drain plug (70).
(n) Install drain plug (70) lightly coated with engine fuel. TORQUE drain plug to between 55 and 45 lbf.in (0.62 and 0.51 m.daN ). Safety with CP8001 SAFETY WIRE 0.032 in. (0.8 mm) dia. CP8002 SAFETY WIRE 0.032 in. (0.8 mm) dia SPM 707012 .
END OF CFM SB 73-0055
Subtask 73-11-10-420-069-A ** ON A/C NOT FOR ALL POST CFM SB 73-0055
NOTE: This subtask is for engines that have a fuel filter cover attachment with six bolts, six washers, six self-aligning nuts and six self-aligning washers.
(1) Install the Fuel Filter Element (20) as follows: WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
(a) Clean the fuel filter housing and the fuel filter cover (40) with de-aromatized petroleum (Material No.CP5074) or isopropyl alcohol (Material No.CP1041) or acetone (Material No.CP1039) . Make sure that the wave spring and retaining ring are correctly installed on the inner boss of the fuel filter cover (40).
PRE CFM SB 73-0107
(b) Install the new AIPC 73-11-10-01-350 O-RING (10) and AIPC 73-11-10-01-350 O-RING (30) in the related groove of the new AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) located at both ends. Soak the new O'rings with engine fuel and slightly lubricate the new O-rings with vaseline (Material No.CP5070) .
END OF PRE CFM SB 73-0107
POST CFM SB 73-0107
(c) Soak the new O'rings located at both ends of the AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) with engine fuel and slightly lubricate the new O'rings with vaseline (Material No.CP5070) .
NOTE: The O'rings are already installed, by the manufacturer, in their groove, inside the new fuel filter element (20).
END OF CFM SB 73-0107
(d) Install the new AIPC 73-11-10-01-310 O-RING (90), in the related groove of the fuel filter cover (40), soak the new O-ring with engine fuel and lubricate it with vaseline (Material No.CP5070) .
(e) Carefully install the fuel filter element (20) into the filter cover (40).
(f) Visually inspect through the fuel filter element (20) that the packing O-ring (30) has not released from its groove and check that the filter element does not move.
CAUTION:
DO NOT USE BOLTS TO HELP COVER FILTER ENGAGEMENT. A WOOD OR PLASTIC HAMMER MAY HELP TO ENGAGE THE COVER IF NECESSARY.
(g) Carefully place the filter cover (40) and the fuel filter element (20) into the filter housing. NOTE: For engines with CFM SB 73-0107 applied, adjust the tabs of the AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) between the ribs of the filter housing.
(h) Before bolt installation, make sure that the cover is well seated against the housing flange. (i) Install the bolts (100) as follows:
CAUTION:
DO NOT INTERMIX THE DIFFERENT HARDWARE OF INSTALLATION KITS. THERE ARE TWO SUPPLIERS FOR THE HARDWARE ASSEMBLY KITS PH030035-4 OR NAS1727-4D. THE SPHERICAL PROFILE OF NUTS AND WASHERS IS DIFFERENT. THESE TWO DIFFERENT HARDWARE HAVE VISUALLY THE SAME DESIGN BUT THEY HAVE DIFFERENT SPHERICAL PROFILES. INCORRECT BOLT, NUT AND WASHER INSTALLATION CAN CAUSE HARDWARE DAMAGE.
1 Lubricate the 6 head faces of the bolt (100) (in contact with the flat washer (110)), the 6 threads of bolts and the 6 spherical sides of the self-aligning nut (120) with graphite compound (Material No. CP2101). 2 Install the 6 bolts (100), the 6 washers (110), the 6 self-aligning washers (130) and nuts (120) to obey the assembly configuration.
(j) Engage the bolt freely by hand (hold the bolt head with fingers, no tool is permitted) and rotate for two complete turns minimum (it should not be possible to fully hand tighten bolts).
(k) Torque the bolts (100).
CAUTION:
YOU MUST TIGHTEN THE BOLTS WITH APPROPRIATE TOOLS (PRESET TORQUE WRENCH). EXCESSIVE TORQUE MAY LEAD TO DAMAGE THE HARDWARE.
1 TORQUE the bolts (100) to between 80 and 70 lbf.in (0.90 and 0.79 m.daN ) . (l) Unscrew the 6 bolts and TORQUE them again to between 80 and 70 lbf.in (0.90 and 0.79 m.daN )
(m) Install a new AIPC 73-11-10-01-290 O-RING (80), soak the new O-ring with engine fuel and lubricate it with vaseline (Material No.CP5070) , on drain plug (70).
(n) Install drain plug (70) lightly coated with engine fuel. TORQUE drain plug to between 55 and 45 lbf.in (0.62 and 0.51 m.daN )
. Safety with END OF CFM SB 73-0055
C. Install the Fuel Filter Element
POST CFM SB 73-A0062
PRE CFM SB 73-0111
PRE CFM SB 73-0107
(b) Install the new AIPC 73-11-10-01-350 O-RING (10) and AIPC 73-11-10-01-350 O-RING (30) in the related groove of the new AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) located at both ends. Soak the new O'rings with engine fuel and slightly lubricate the new O'rings with vaseline (Material No.CP5070) .
END OF PRE CFM SB 73-0107
POST CFM SB 73-0107
(c) Soak the new O'rings located at both ends of the AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) with engine fuel and slightly lubricate the new O'rings with vaseline (Material No.CP5070) .
END OF POST CFM SB 73-0107
(d) Install the new AIPC 73-11-10-01-310 O-RING (90) in the related groove of the fuel filter cover (40), soak the new O-ring with engine fuel and lubricate it with vaseline (Material No.CP5070) .
(e) Carefully install the fuel filter element (20) into the filter cover (40).
(f) Visually inspect through the fuel filter element (20) that the O-ring (30) has not released from its groove and check that the filter element does not move.
(g) Apply the following material.
(h) Carefully install the fuel filter element (20) and the cover (40) into the filter housing.
(j) Install flat washers (330) and nuts (320).
(k) Make sure that the nuts (320) screw freely by hand, as follows:
(l) Install flat washer (340) and bolt (350).
(n) TORQUE the nuts (320) and the bolt (350) to between 80 and 70 lbf.in (0.90 and 0.79 m.daN ).
(o) Soak a new AIPC 73-11-10-01-290 O-RING (80) with engine fuel and lubricate it with vaseline (Material No.CP5070) and install the O-ring on the drain plug (70).
(p) Lightly lubricate the drain plug thread (70) with engine fuel. Install and TORQUE the drain plug (70) to between 55 and 45 lbf.in (0.62 and 0.51 m.daN ). Safety with CP8001 SAFETY WIRE 0.032 in. (0.8 mm) dia. CP8002 SAFETY WIRE 0.032 in. (0.8 mm) dia SPM 707012 .
END OF POST CFM SB 73-A0062
END OF PRE CFM SB 73-0111
Subtask 73-11-10-420-070-A ** ON A/C NOT FOR ALL POST CFM SB 73-A0062
PRE CFM SB 73-0111
NOTE: This subtask is for engines that have a fuel filter cover attachment with five D-HEAD bolts, five retaining rings, five washers, five nuts (5 locations) and one normal bolt, one washer with fuel pump housing insert (1 location).
(1) Install the Fuel Filter Element (20) as follows: WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
(a) Clean the fuel filter housing and cover (40) with de-aromatized petroleum (Material No.CP5074) or isopropyl alcohol (Material No.CP1041) or acetone (Material No.CP1039) . Make sure that the spring washer and retaining ring are correctly installed on the inner boss of the cover (40). PRE CFM SB 73-0107
(b) Install the new AIPC 73-11-10-01-350 O-RING (10) and AIPC 73-11-10-01-350 O-RING (30) in the related groove of the new AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) located at both ends. Soak the new O'rings with engine fuel and slightly lubricate the new O'rings with vaseline (Material No.CP5070) .
END OF PRE CFM SB 73-0107
POST CFM SB 73-0107
(c) Soak the new O'rings located at both ends of the AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) with engine fuel and slightly lubricate the new O'rings with vaseline (Material No.CP5070) .
NOTE: The O'rings are already installed, by the manufacturer, in their groove, inside the new fuel filter element (20).
END OF POST CFM SB 73-0107
(d) Install the new AIPC 73-11-10-01-310 O-RING (90) in the related groove of the fuel filter cover (40), soak the new O-ring with engine fuel and lubricate it with vaseline (Material No.CP5070) .
(e) Carefully install the fuel filter element (20) into the filter cover (40).
(f) Visually inspect through the fuel filter element (20) that the O-ring (30) has not released from its groove and check that the filter element does not move.
(g) Apply the following material.
CAUTION:
DO NOT USE BOLTS TO HELP COVER FILTER ENGAGEMENT. A WOOD OR PLASTIC HAMMER MAY HELP TO ENGAGE THE COVER IF NECESSARY.
1 Apply graphite grease (Material No.CP2101) on the 5 D-bolt (300) threads, flat washers (330), nuts (320) (face in contact with flat washer) and on the bolt (350) thread. (h) Carefully install the fuel filter element (20) and the cover (40) into the filter housing.
NOTE: For engines with CFM SB 73-0107 applied, adjust the tabs of the AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) between the ribs of the filter housing.
(i) Before bolt installation, make sure that the cover is correctly seated against the housing flange. (j) Install flat washers (330) and nuts (320).
(k) Make sure that the nuts (320) screw freely by hand, as follows:
NOTE: No tools are permitted.
1 Rotate each nut for two complete turns minimum. If the attaching part is in good condition, it should not be possible to fully hand tighten the nut. (l) Install flat washer (340) and bolt (350).
NOTE: Only one bolt is used in the hole adjacent to the nameplate.
(m) Make sure that the bolt engages freely by hand, as follows: NOTE: No tools are permitted.
1 Hold the bolt head between your fingers and rotate the bolt the minimum number of turns. If the insert is in good condition, it should not be possible to fully hand tighten the bolt. (n) TORQUE the nuts (320) and the bolt (350) to between 80 and 70 lbf.in (0.90 and 0.79 m.daN )
. (o) Soak a new AIPC 73-11-10-01-290 O-RING (80) with engine fuel and lubricate it with vaseline (Material No.CP5070) and install the O-ring on the drain plug (70).
(p) Lightly lubricate the drain plug thread (70) with engine fuel. Install and TORQUE the drain plug (70) to between 55 and 45 lbf.in (0.62 and 0.51 m.daN )
. Safety with END OF POST CFM SB 73-A0062
END OF PRE CFM SB 73-0111
D. Install the Fuel Filter Element
POST CFM SB 73-0111
PRE CFM SB 73-0107
(b) Install the new AIPC 73-11-10-01-350 O-RING (10) and AIPC 73-11-10-01-350 O-RING (30) in the related groove of the new AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) located at both ends. Soak the new O'rings with engine fuel and slightly lubricate the new O'rings with vaseline (Material No.CP5070) .
END OF PRE CFM SB 73-0107
POST CFM SB 73-0107
(c) Soak the new O'rings located at both ends of the AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) with engine fuel and lubricate slightly the new O'rings with vaseline (Material No.CP5070) .
END OF POST CFM SB 73-0107
(d) Install the new AIPC 73-11-10-01-310 O-RING (90) in the related groove of the fuel filter cover (40), soak the new O-ring with engine fuel and lubricate it with vaseline (Material No.CP5070) .
(e) Carefully install fuel filter element (20) into the filter cover (40).
(f) Visually inspect through the fuel filter element (20) that the packing O-ring (30) has not released from its groove and check that the fuel filter element does not move.
(g) Apply graphite grease (Material No.CP2101) on the 5 D-bolt (300) threads, flat washers (330), nuts (320) (face in contact with flat washer) and on the bolt (110) or (120) thread.
2 Install the bolt (100), the washer (110), the self-aligning washer (130) and nuts (120) to obey the assembly configuration.
(k) Engage the bolt (100) freely by hand, as follows:
(l) Install flat washers (330) and nuts (320).
(m) Make sure that the nuts (320) screw freely by hand, as follows:
(n) TORQUE the bolt (100) to between 80 and 70 lbf.in (0.90 and 0.79 m.daN ).
(o) Unscrew the bolt (100) and TORQUE it again to between 80 and 70 lbf.in (0.90 and 0.79 m.daN ).
(p) TORQUE the nuts (320) to between 80 and 70 lbf.in (0.90 and 0.79 m.daN ).
(q) Soak a new AIPC 73-11-10-01-290 O-RING (80) with engine fuel, lubricate it with vaseline (Material No.CP5070) and install the O-ring on the drain plug (70).
(r) Lightly lubricate the drain plug thread (70) with engine fuel. Install and TORQUE the drain plug (70) to between 55 and 45 lbf.in (0.62 and 0.51 m.daN ). Safety with CP8001 SAFETY WIRE 0.032 in. (0.8 mm) dia. CP8002 SAFETY WIRE 0.032 in. (0.8 mm) dia SPM 707012 .
END OF POST CFM SB 73-0111
Subtask 73-11-10-710-057-A ** ON A/C NOT FOR ALL 5. Close-upPOST CFM SB 73-0111
NOTE: This subtask is for engines that have a fuel filter cover attachment with five D-HEAD bolts, retaining rings, washers, nuts (5 locations) (repaired by the application of CFM SB 73-A0062) and one bolt, washer, self-aligning washer and self-aligning nut (1 location).
(1) Install the Fuel Filter Element (20) as follows: WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
(a) Clean the fuel filter housing and cover (40) with de-aromatized petroleum (Material No.CP5074) or isopropyl alcohol (Material No.CP1041) or acetone (Material No.CP1039) . Make sure that the spring washer and retaining ring are correctly installed on the inner boss of the cover (40). PRE CFM SB 73-0107
(b) Install the new AIPC 73-11-10-01-350 O-RING (10) and AIPC 73-11-10-01-350 O-RING (30) in the related groove of the new AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) located at both ends. Soak the new O'rings with engine fuel and slightly lubricate the new O'rings with vaseline (Material No.CP5070) .
END OF PRE CFM SB 73-0107
POST CFM SB 73-0107
(c) Soak the new O'rings located at both ends of the AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) with engine fuel and lubricate slightly the new O'rings with vaseline (Material No.CP5070) .
NOTE: The O'rings are already installed, by the manufacturer, in their groove, inside the new fuel filter element (20).
END OF POST CFM SB 73-0107
(d) Install the new AIPC 73-11-10-01-310 O-RING (90) in the related groove of the fuel filter cover (40), soak the new O-ring with engine fuel and lubricate it with vaseline (Material No.CP5070) .
(e) Carefully install fuel filter element (20) into the filter cover (40).
(f) Visually inspect through the fuel filter element (20) that the packing O-ring (30) has not released from its groove and check that the fuel filter element does not move.
(g) Apply graphite grease (Material No.CP2101) on the 5 D-bolt (300) threads, flat washers (330), nuts (320) (face in contact with flat washer) and on the bolt (110) or (120) thread.
CAUTION:
DO NOT USE BOLTS TO HELP COVER FILTER ENGAGEMENT. A WOOD OR PLASTIC HAMMER MAY HELP TO ENGAGE THE COVER IF NECESSARY.
(h) Carefully install the filter element (20) and the cover (40) into the filter housing. NOTE: For engines with CFM SB 73-0107 applied, adjust the tabs of the AIPC 73-11-10-01-340 FUEL FILTER ELEMENT (20) between the ribs of the filter housing.
(i) Before bolt installation, make sure that the cover is correctly seated against the housing flange. CAUTION:
DO NOT INTERMIX THE DIFFERENT HARDWARE OF INSTALLATION KITS. THERE ARE TWO SUPPLIERS FOR THE HARDWARE ASSEMBLY KITS PH030035-4 OR NAS1727-4D. THE SPHERICAL PROFILE OF NUTS AND WASHERS IS DIFFERENT. THESE TWO DIFFERENT HARDWARE HAVE VISUALLY THE SAME DESIGN BUT THEY HAVE DIFFERENT SPHERICAL PROFILES. INCORRECT BOLT, NUT AND WASHER INSTALLATION CAN CAUSE HARDWARE DAMAGE.
(j) Install the bolts (100) as follows: NOTE: Only one bolt is used in the hole adjacent to the nameplate.
1 Lubricate the head face of the bolt (100) (in contact with the flat washer (110)), the thread of the bolt and the spherical side of the self- aligning nut (120) with graphite compound (Material No. CP2101). 2 Install the bolt (100), the washer (110), the self-aligning washer (130) and nuts (120) to obey the assembly configuration.
(k) Engage the bolt (100) freely by hand, as follows:
NOTE: No tools are permitted.
1 Hold the bolt head between your fingers and rotate the bolt the minimum number of turns. If the thread of the self-aligning nut (120) is in good condition, it should not be possible to fully hand tighten the bolt. (l) Install flat washers (330) and nuts (320).
(m) Make sure that the nuts (320) screw freely by hand, as follows:
NOTE: No tools are permitted.
1 Rotate each nut for two complete turns minimum. If the attaching part is in good condition, it should not be possible to fully hand tighten the nut. (n) TORQUE the bolt (100) to between 80 and 70 lbf.in (0.90 and 0.79 m.daN )
. (o) Unscrew the bolt (100) and TORQUE it again to between 80 and 70 lbf.in (0.90 and 0.79 m.daN )
. (p) TORQUE the nuts (320) to between 80 and 70 lbf.in (0.90 and 0.79 m.daN )
. (q) Soak a new AIPC 73-11-10-01-290 O-RING (80) with engine fuel, lubricate it with vaseline (Material No.CP5070) and install the O-ring on the drain plug (70).
(r) Lightly lubricate the drain plug thread (70) with engine fuel. Install and TORQUE the drain plug (70) to between 55 and 45 lbf.in (0.62 and 0.51 m.daN )
. Safety with END OF POST CFM SB 73-0111
Subtask 73-11-10-410-063-A ** ON A/C NOT FOR ALL
A. Close Access
(1) Remove the container from under the engine.
(2) Make sure that the work area is clean and clear of tools and other items.
(3) Close the fan cowl doors: (Ref. AMM TASK 71-13-00-410-040)
(4) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(5) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(6) Remove the WARNING NOTICE(S).
(1) Remove the container from under the engine.
(2) Make sure that the work area is clean and clear of tools and other items.
(3) Close the fan cowl doors: (Ref. AMM TASK 71-13-00-410-040)
(4) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(5) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(6) Remove the WARNING NOTICE(S).