DOC AIRBUS | AMM A320FRemoval of the Drain Manifold Module [CFMB]
TASK 71-71-43-000-041-A
Removal of the Drain Manifold Module
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 71-71-43-941-050-A ** ON A/C NOT FOR ALL
Subtask 71-71-43-020-050-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 12:55:25 UTC
Removal of the Drain Manifold Module
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | CONTAINER 20 L - SHALLOW |
| No specific | AR | COVER - PROTECTION |
| No specific | AR | WARNING NOTICE(S) |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| FOR [1000EM1] (ENGINE-1) | |
| 437AL, 438AR | |
| FOR [1000EM2] (ENGINE-2) | |
| 447AL, 448AR | |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 71-13-00-010-040-B | Opening of the Fan Cowl Doors |
| TASK 71-71-42-000-041-A | Removal of the Drain Mast |
Drain Manifold ModuleSubtask 71-71-43-941-050-A ** ON A/C NOT FOR ALL
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
Subtask 71-71-43-010-051-A ** ON A/C NOT FOR ALL (1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
B. Open the fan cowl doors: (Ref. AMM TASK 71-13-00-010-040)
(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR
4. Procedure(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR
Subtask 71-71-43-020-050-A ** ON A/C NOT FOR ALL
A. Removal of the Drain Manifold Module
(1) Remove the drain mast (Ref. AMM TASK 71-71-42-000-041)
(2) Put the CONTAINER 20 L - SHALLOW below the drain manifold module to catch unwanted fluids.
(3) Disconnect:
(b) Disconnect the heat exchanger, the fan case, and the oil tank scupper tubes from the left side of the manifold module (20).
(4) Remove the bolts (5), the washers (10), and the nuts (15) that attach the manifold module (20) to the engine brackets.
(5) Remove the drain manifold module (20) from the engine.
(6) Install COVER - PROTECTION on the drain tubes and the module.
(1) Remove the drain mast (Ref. AMM TASK 71-71-42-000-041)
(2) Put the CONTAINER 20 L - SHALLOW below the drain manifold module to catch unwanted fluids.
(3) Disconnect:
CAUTION:
USE A SECOND WRENCH TO HOLD THE FITTINGS WHEN YOU LOOSEN/TIGHTEN THE TUBE COUPLING NUTS. THIS PREVENTS DAMAGE TO THE TUBES.
(a) Disconnect the oil/hydraulic, the fuel, and the reservoir module tubes from the right side of the drain manifold module (20). (b) Disconnect the heat exchanger, the fan case, and the oil tank scupper tubes from the left side of the manifold module (20).
(4) Remove the bolts (5), the washers (10), and the nuts (15) that attach the manifold module (20) to the engine brackets.
(5) Remove the drain manifold module (20) from the engine.
(6) Install COVER - PROTECTION on the drain tubes and the module.