Inspection-Trimmable Horizontal Stabilizer Leading Edge
TASK 55-12-11-200-001-A
Inspection-Trimmable Horizontal Stabilizer Leading Edge
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 55-12-11-860-051-A
Subtask 55-12-11-210-051-B
Subtask 55-12-11-410-051-A
[Rev.10 from 2021]
2026.04.01 02:04:47 UTC
Inspection-Trimmable Horizontal Stabilizer Leading Edge
WARNING:
PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
WARNING:
MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
WARNING:
YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU START WORK:
- ON THE THS OR IN THE REAR FUSELAGE
- ON TOP OF THE WINGS OR PYLONS.
WARNING:
MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
CAUTION:
DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF CARBONFIBER REINFORCED PLASTIC.
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | ACCESS PLATFORM 4M (13 FT) |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| No specific | AR | WARNING NOTICE(S) |
| 98D27903500000 | 2 | PIN-SIDE STICK LOCKING |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 330 | THS LH AND LH ELEVATOR |
| 340 | THS RH AND RH ELEVATOR |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 29-10-00-864-001-A | Depressurize the Green Hydraulic System |
| TASK 29-10-00-864-002-A | Depressurize the Yellow Hydraulic System |
| TASK 29-10-00-864-003-A | Depressurize the Blue Hydraulic System |
| SRM 551200 | |
Subtask 55-12-11-860-051-A
A. Depressurize Hydraulic Systems
(1) Depressurize the Green,Yellow, and Blue hydraulic systems (Ref. AMM TASK 29-10-00-864-001) (Ref. AMM TASK 29-10-00-864-002) (Ref. AMM TASK 29-10-00-864-003).
Subtask 55-12-11-865-054-A (1) Depressurize the Green,Yellow, and Blue hydraulic systems (Ref. AMM TASK 29-10-00-864-001) (Ref. AMM TASK 29-10-00-864-002) (Ref. AMM TASK 29-10-00-864-003).
B. Open, safety and tag this(these) circuit breaker(s):
Subtask 55-12-11-481-051-A | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | FLIGHT CONTROLS/THS/ACTR/MOT2 | 19CE2 | B09 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | FLIGHT CONTROLS/THS/ACTR/MOT2 | 19CE2 | B04 |
| ** ON A/C ALL | |||
| 121VU | FLIGHT CONTROLS/THS ACTR/MOT3 | 19CE3 | Q17 |
| 121VU | FLIGHT CONTROLS/THS ACTR/MOT1 | 19CE1 | Q16 |
C. Install Locking Devices
(1) Install the 98D27903500000 PIN-SIDE STICK LOCKING in the CAPT and F/O side stick controllers.
Subtask 55-12-11-941-051-A (1) Install the 98D27903500000 PIN-SIDE STICK LOCKING in the CAPT and F/O side stick controllers.
D. Safety Precautions
(1) Put the WARNING NOTICE(S) in the flight compartment to tell persons not to operate the flight controls
(2) Put the WARNING NOTICE(S) in position to tell persons not to operate the hydraulic systems.
(3) Put the ACCESS PLATFORM 4M (13 FT) in position at zone 334 for the left hand trimmable horizontal stabilizer leading edge and/or zone 344 for the right hand trimmable horizontal stabilizer leading edge.
4. Procedure(1) Put the WARNING NOTICE(S) in the flight compartment to tell persons not to operate the flight controls
(2) Put the WARNING NOTICE(S) in position to tell persons not to operate the hydraulic systems.
(3) Put the ACCESS PLATFORM 4M (13 FT) in position at zone 334 for the left hand trimmable horizontal stabilizer leading edge and/or zone 344 for the right hand trimmable horizontal stabilizer leading edge.
Subtask 55-12-11-210-051-B
A. Visual Inspection
(1) Examine the leading edge sections to make sure that:
5. Close-up(1) Examine the leading edge sections to make sure that:
- There is no distortion.
- There are no loose screws.
- There is no damage on the stainless-steel anti-erosion covers.
- There is no damage on the paint finish.
Subtask 55-12-11-410-051-A
A. Visual Inspection
(1) Make sure that the work area is clean and clear of tools and other items.
Subtask 55-12-11-942-054-A (1) Make sure that the work area is clean and clear of tools and other items.
B. Remove Ground Equipment
(1) Remove the WARNING NOTICE(S).
(2) Remove the access platform(s).
Subtask 55-12-11-081-051-A (1) Remove the WARNING NOTICE(S).
(2) Remove the access platform(s).
C. Remove Locking Devices
(1) Remove the 98D27903500000 PIN-SIDE STICK LOCKING from the CAPT and F/O side stick controllers.
Subtask 55-12-11-865-055-A (1) Remove the 98D27903500000 PIN-SIDE STICK LOCKING from the CAPT and F/O side stick controllers.
D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | FLIGHT CONTROLS/THS/ACTR/MOT2 | 19CE2 | B09 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | FLIGHT CONTROLS/THS/ACTR/MOT2 | 19CE2 | B04 |
| ** ON A/C ALL | |||
| 121VU | FLIGHT CONTROLS/THS ACTR/MOT3 | 19CE3 | Q17 |
| 121VU | FLIGHT CONTROLS/THS ACTR/MOT1 | 19CE1 | Q16 |
Inspection Area of the Horizontal Stabilizer Leading-Edge