DOC AIRBUS | AMM A320FRemoval of the Auxiliary/Mirror Lavatory Light
TASK 33-51-14-000-006-A
Removal of the Auxiliary/Mirror Lavatory Light
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Referenced Information
3. Job Set-up
Subtask 33-51-14-010-064-A ** ON A/C NOT FOR ALL
Subtask 33-51-14-020-059-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 06:20:03 UTC
Removal of the Auxiliary/Mirror Lavatory Light
WARNING:
MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT. UNWANTED ELECTRICAL POWER CAN BE DANGEROUS.
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | CAP - BLANKING |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 25-40-00-00 | LAVATORIES - DESCRIPTION AND OPERATION |
Removal/Installation of Auxiliary LightSubtask 33-51-14-010-064-A ** ON A/C NOT FOR ALL
A. Get Access
(1) For the location of the related lavatory, refer to Para. Component Location (Ref. AMM D/O 25-40-00-00).
(2) Get access to the related lavatory and open the lavatory door.
Subtask 33-51-14-865-072-A ** ON A/C NOT FOR ALL (1) For the location of the related lavatory, refer to Para. Component Location (Ref. AMM D/O 25-40-00-00).
(2) Get access to the related lavatory and open the lavatory door.
B. Open, safety and tag this(these) circuit breaker(s):
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H07 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H05 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD-OCCUPIED | 1WJ | F01 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD & MID-OCCUPIED | 1WJ | F01 |
| ** ON A/C NOT FOR ALL | |||
| 2001VU | LAVATORY AFT-OCCUPIED | 11WJ | B04 |
Subtask 33-51-14-020-059-A ** ON A/C NOT FOR ALL
A. Removal of Auxiliary Light
(1) Remove the light unit (2):
(a) Hold the light unit (2) and remove the screws (1).
(c) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(d) Remove the light unit (2).
(1) Remove the light unit (2):
(a) Hold the light unit (2) and remove the screws (1).
CAUTION:
MAKE SURE THAT THE ELECTRICAL CONNECTORS ARE CLEAN BEFORE YOU DISCONNECT OR CONNECT THEM. CONTAMINATION ON THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO EQUIPMENT.
CAUTION:
MAKE MATCH MARKS ON ALL THE ELECTRICAL WIRES BEFORE YOU DISCONNECT THEM. INCORRECT CONNECTION OF WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
(b) Disconnect the electrical connectors (3) from the light unit (2). (c) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(d) Remove the light unit (2).