Installation of the Taxi Light

TASK 33-46-12-400-001-A
Installation of the Taxi Light

WARNING: WEAR GLASSES AND PROTECTIVE CLOTHING WHEN YOU DO WORK ON THE LIGHT. THE LAMP IS PRESSURIZED AND AN EXPLOSION CAN OCCUR.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 711
FIN: 8LR

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	Torque wrench: range to between 0.75 and 0.6 m.daN (66.37 and 53.10 lbf.in )

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.06LCG9)	Non Hardening Jointing Putty-Medium Temp. Area - -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
711	NOSE GEAR

D. Referenced Information

REFERENCE	DESIGNATION
TASK 33-46-00-710-001-A	Operational Test of the Taxi and Take Off Lights
Taxi Light

3. Job Set-up
Subtask 33-46-12-865-051-A

A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
122VU	LIGHTING/EXT LT/TAXI AND TAKE OFF/TAXI	1LR	W08

4. Procedure
Subtask 33-46-12-420-050-E

A. Installation of the Taxi Light
(1) Clean the component interfaces and the adjacent area.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) For the LED taxi light:
(a) Make sure that the lens retainer assembly of the LED taxi light is in the correct condition.
(4) For the incandescent lamp or the substitute halogen-lamp assembly:
(a) Make sure that the filament of the lamp (or bulb) and the lens of the optical unit are in the correct condition.
(5) Make sure that the clamp is correctly installed.
(6) Put the light (9) on its support (1).
(7) Apply Non Hardening Jointing Putty-Medium Temp. Area - - (Material No.06LCG9) to the screws (2) and (3).
(8) Install the light (9) in the lower fork on the support (1).
(9) Install the screw (3) in the support (1).
(10) Install the washer (5) and the nut (6).
(11) Torque the nut (6) to between 0.75 and 0.6 m.daN (66.37 and 53.10 lbf.in )

.
(12) Turn the light to the upper forks.
(13) Install the screws (2) in the support (1).
(14) Install the washers (4) and the nuts (7).
(15) Torque the nuts (7) to between 0.75 and 0.6 m.daN (66.37 and 53.10 lbf.in )

.
(16) Remove the blanking caps from the electrical connector (10) and the socket (8).
(17) Make sure that the electrical connector (10) and the socket (8) are in the correct condition.
(18) Connect the electrical connector (10) to the socket (8) and lock it.

Subtask 33-46-12-865-052-A

B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
122VU	LIGHTING/EXT LT/TAXI AND TAKE OFF/TAXI	1LR	W08

Subtask 33-46-12-710-051-A

C. Operational Test of the Light
(1) Do the operational test of the taxi light (Ref. AMM TASK 33-46-00-710-001).

5. Close-up
Subtask 33-46-12-942-050-A

A. Make sure that the work area is clean and clear of tools and other items.

[Rev.10 from 2021] 2026.04.01 12:30:33 UTC