Removal of the Power Unit for the Cabin Attendant Work-Light
TASK 33-27-38-000-001-A
Removal of the Power Unit for the Cabin Attendant Work-Light
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Referenced Information
3. Job Set-up
Subtask 33-27-38-865-052-A ** ON A/C NOT FOR ALL
Subtask 33-27-38-020-050-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 00:54:04 UTC
Removal of the Power Unit for the Cabin Attendant Work-Light
FIN: 12LZ ** ON A/C NOT FOR ALL
FIN: 13LZ ** ON A/C NOT FOR ALL
FIN: 3LZ ** ON A/C NOT FOR ALL
FIN: 512RHF ** ON A/C NOT FOR ALL
FIN: 512RHG ** ON A/C NOT FOR ALL
FIN: 512RHN ** ON A/C NOT FOR ALL
1. Reason for the JobFIN: 13LZ ** ON A/C NOT FOR ALL
FIN: 3LZ ** ON A/C NOT FOR ALL
FIN: 512RHF ** ON A/C NOT FOR ALL
FIN: 512RHG ** ON A/C NOT FOR ALL
FIN: 512RHN ** ON A/C NOT FOR ALL
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | CAP - BLANKING |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| FOR [12LZ] (ATT WORK LIGHT) | ||
| No specific | 1 | STEPLADDER 1.0 M (3.3 FT) |
| FOR [13LZ] (POWER UNIT) | ||
| No specific | 1 | STEPLADDER 1.0 M (3.3 FT) |
| FOR [3LZ] (PCB ATTND WORK LT) | ||
| No specific | 1 | STEPLADDER 1.0 M (3.3 FT) |
| REFERENCE | DESIGNATION |
|---|---|
Subtask 33-27-38-865-052-A ** ON A/C NOT FOR ALL
A. Open, safety and tag this(these) circuit breaker(s):
Subtask 33-27-38-010-050-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LIGHT-ATTND-WORK | 1LZ | J03 |
B. Get Access
(1) FOR [3LZ] (PCB ATTND WORK LT)
(a) Put the STEPLADDER 1.0 M (3.3 FT) in position below the related panel.
(b) Lower the circuit breaker panel 2000VU.
(2) FOR [12LZ] (ATT WORK LIGHT)
(a) Put the STEPLADDER 1.0 M (3.3 FT) in position below the related panel.
(b) Lower the circuit breaker panel 2001VU.
(3) FOR [13LZ] (POWER UNIT)
(a) Put the STEPLADDER 1.0 M (3.3 FT) in position below the related panel.
(b) Disengage and lower one side of the combi panel 2042VU.
4. Procedure(1) FOR [3LZ] (PCB ATTND WORK LT)
(a) Put the STEPLADDER 1.0 M (3.3 FT) in position below the related panel.
(b) Lower the circuit breaker panel 2000VU.
(2) FOR [12LZ] (ATT WORK LIGHT)
(a) Put the STEPLADDER 1.0 M (3.3 FT) in position below the related panel.
(b) Lower the circuit breaker panel 2001VU.
(3) FOR [13LZ] (POWER UNIT)
(a) Put the STEPLADDER 1.0 M (3.3 FT) in position below the related panel.
(b) Disengage and lower one side of the combi panel 2042VU.
Subtask 33-27-38-020-050-A ** ON A/C NOT FOR ALL
A. Removal of the Power Unit(s) for the Cabin Attendant Work-Lights
(1) Disconnect the electrical connectors (2) and (3).
(2) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(3) Removal of the Power Units 3LZ, 12LZ
(a) Remove the screws (5), the washers (6), the nuts (8) and the power unit (1).
(4) Removal of the Power Unit 13LZ
(a) Remove the screws (5), the washers (6), the spacers (10), and the power unit (1).
(1) Disconnect the electrical connectors (2) and (3).
(2) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(3) Removal of the Power Units 3LZ, 12LZ
(a) Remove the screws (5), the washers (6), the nuts (8) and the power unit (1).
(4) Removal of the Power Unit 13LZ
(a) Remove the screws (5), the washers (6), the spacers (10), and the power unit (1).
Power Unit