Inspection/Check of the Spoiler 1

TASK 27-64-41-200-001-A
Inspection/Check of the Spoiler 1

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:

DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.

1. Reason for the Job
Because the free movement is more than that in TASK 27-64-00-200-001.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	SAFETY BARRIER(S)
No specific	AR	WARNING NOTICE(S)

B. Referenced Information

REFERENCE	DESIGNATION
TASK 27-64-41-000-001-A	Removal of the Spoiler 1
TASK 27-64-41-400-001-A	Installation of the Spoiler 1
Spoiler 1 ** ON A/C NOT FOR ALL
Spoiler 1 ** ON A/C NOT FOR ALL
Spoiler 1 ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 27-64-41-941-054-A

A. Safety Precautions
(1) Put the SAFETY BARRIER(S) in position.
(2) Put a WARNING NOTICE(S) in position to tell persons not to operate the flight controls.

Subtask 27-64-41-010-051-A

B. Get Access
(1) Remove the spoiler 1 (Ref. AMM TASK 27-64-41-000-001).

4. Procedure

CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:

DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.

Subtask 27-64-41-220-051-A

A. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
B	19.030	19.043			19.000
OD 2	(0.7492)	(0.7497)			(0.7480)
			0.0070	0.0530			0.1130
			(0.0003)	(0.0021)			(0.0044)
B	19.050	19.083				19.113
ID 1	(0.7500)	(0.7513)				(0.7525)

Subtask 27-64-41-220-052-A

B. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
B	12.683	12.694			12.658
OD 3	(0.4993)	(0.4998)			(0.4983)
			0.0060	0.0440			0.0940
			(0.0002)	(0.0017)			(0.0037)
B	12.700	12.727				12.752
ID 2	(0.5000)	(0.5011)				(0.5020)

Subtask 27-64-41-220-053-A

C. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
B	12.683	12.694			12.658
OD 3	(0.4993)	(0.4998)			(0.4983)
			0.0060	0.0440			0.0940
			(0.0002)	(0.0017)			(0.0037)
B	12.700	12.727				12.752
ID 4	(0.5000)	(0.5011)				(0.5020)

Subtask 27-64-41-220-054-A

D. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
B	19.030	19.043			19.000
OD 4	(0.7492)	(0.7497)			(0.7480)
			0.0070	0.0530			0.1130
			(0.0003)	(0.0021)			(0.0044)
B	19.050	19.083				19.113
ID 1	(0.7500)	(0.7513)				(0.7525)

Subtask 27-64-41-220-055-A

E. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
B	12.683	12.694			12.658
OD 3	(0.4993)	(0.4998)			(0.4983)
			0.0060	0.0440			0.0940
			(0.0002)	(0.0017)			(0.0037)
B	12.700	12.727				12.752
ID 5	(0.5000)	(0.5011)				(0.5020)

Subtask 27-64-41-220-056-A

F. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
B	15.801	15.828			15.747
OD 5	(0.6221)	(0.6231)			(0.6200)
			0.0340	0.0740			0.1820
			(0.0013)	(0.0029)			(0.0072)
B	15.862	15.875				15.929
ID 6	(0.6245)	(0.6250)				(0.6271)

Subtask 27-64-41-220-057-A

G. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
C	25.380	25.393			25.350
OD 2	(0.9992)	(0.9997)			(0.9980)
			0.0070	0.0530			0.1130
			(0.0003)	(0.0021)			(0.0044)
C	25.400	25.433				25.463
ID 1	(1.0000)	(1.0013)				(1.0025)

Subtask 27-64-41-220-058-A

H. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
C	19.030	19.043			19.000
OD 3	(0.7492)	(0.7497)			(0.7480)
			0.0070	0.0530			0.1130
			(0.0003)	(0.0021)			(0.0044)
C	19.050	19.083				19.113
ID 2	(0.7500)	(0.7513)				(0.7525)

Subtask 27-64-41-220-059-A

I. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
C	19.030	19.043			19.000
OD 3	(0.7492)	(0.7497)			(0.7480)
			0.0070	0.0530			0.1130
			(0.0003)	(0.0021)			(0.0044)
C	19.050	19.083				19.113
ID 4	(0.7500)	(0.7513)				(0.7525)

Subtask 27-64-41-220-060-A

J. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
C	19.030	19.043			19.000
OD 3	(0.7492)	(0.7497)			(0.7480)
			0.0070	0.0530			0.1130
			(0.0003)	(0.0021)			(0.0044)
C	19.050	19.083				19.113
ID 5	(0.7500)	(0.7513)				(0.7525)

Subtask 27-64-41-220-061-A

K. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
C	22.152	22.185			22.102
OD 5	(0.8721)	(0.8734)			(0.8702)
			0.0270	0.0730			0.1730
			(0.0011)	(0.0029)			(0.0068)
C	22.212	22.225				22.275
ID 6	(0.8745)	(0.8750)				(0.8770)

Subtask 27-64-41-220-062-A

L. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
D	19.030	19.043			19.000
OD 2	(0.7492)	(0.7497)			(0.7480)
			0.0070	0.0530			0.1130
			(0.0003)	(0.0021)			(0.0044)
D	19.050	19.083				19.113
ID 1	(0.7500)	(0.7513)				(0.7525)

Subtask 27-64-41-220-063-A

M. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
D	12.683	12.694			12.658
OD 3	(0.4993)	(0.4998)			(0.4983)
			0.0060	0.0440			0.0940
			(0.0002)	(0.0017)			(0.0037)
D	12.700	12.727				12.752
ID 2	(0.5000)	(0.5011)				(0.5020)

Subtask 27-64-41-220-064-A

N. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
D	12.683	12.694			12.658
OD 3	(0.4993)	(0.4998)			(0.4983)
			0.0060	0.0440			0.0940
			(0.0002)	(0.0017)			(0.0037)
D	12.700	12.727				12.752
ID 4	(0.5000)	(0.5011)				(0.5020)

Subtask 27-64-41-220-065-A

O. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
D	19.030	19.043			19.000
OD 4	(0.7492)	(0.7497)			(0.7480)
			0.0070	0.0530			0.1130
			(0.0003)	(0.0021)			(0.0044)
D	19.050	19.083				19.113
ID 1	(0.7500)	(0.7513)				(0.7525)

Subtask 27-64-41-220-066-A

P. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
D	12.683	12.694			12.658
OD 3	(0.4993)	(0.4998)			(0.4983)
			0.0060	0.0440			0.0940
			(0.0002)	(0.0017)			(0.0037)
D	12.700	12.727				12.752
ID 5	(0.5000)	(0.5011)				(0.5020)

Subtask 27-64-41-220-067-A

Q. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
D	15.801	15.828			15.747
OD 5	(0.6221)	(0.6231)			(0.6200)
			0.0340	0.0730			0.1810
			(0.0013)	(0.0029)			(0.0071)
D	15.862	15.874				15.928
ID 6	(0.6245)	(0.6250)				(0.6271)

Subtask 27-64-41-220-068-A

R. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
E	25.380	25.393			25.350
OD 2	(0.9992)	(0.9997)			(0.9980)
			0.0070	0.0530			0.1130
			(0.0003)	(0.0021)			(0.0044)
E	25.400	25.433				25.463
ID 1	(1.0000)	(1.0013)				(1.0025)

Subtask 27-64-41-220-069-A

S. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
E	19.030	19.043			19.000
OD 3	(0.7492)	(0.7497)			(0.7480)
			0.0070	0.0530			0.1130
			(0.0003)	(0.0021)			(0.0044)
E	19.050	19.083				19.113
ID 2	(0.7500)	(0.7513)				(0.7525)

Subtask 27-64-41-220-070-A

T. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
E	19.030	19.043			19.000
OD 3	(0.7492)	(0.7497)			(0.7480)
			0.0070	0.0530			0.1130
			(0.0003)	(0.0021)			(0.0044)
E	19.050	19.083				19.113
ID 4	(0.7500)	(0.7513)				(0.7525)

Subtask 27-64-41-220-071-A

U. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
E	22.152	22.185			22.102
OD 4	(0.8721)	(0.8734)			(0.8702)
			0.0270	0.0730			0.1730
			(0.0011)	(0.0029)			(0.0068)
E	22.212	22.225				22.275
ID 5	(0.8745)	(0.8750)				(0.8770)

Subtask 27-64-41-220-072-B

V. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
F	28.534	28.555			28.493
OD 2	(1.1234)	(1.1242)			(1.1218)
			0.0200	0.0620			0.1440
			(0.0008)	(0.0024)			(0.0057)
F	28.575	28.596				28.637
ID 1	(1.1250)	(1.1258)				(1.1274)

Subtask 27-64-41-220-073-B

W. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
F	20.959	20.980			20.918
OD 3	(0.8252)	(0.8260)			(0.8235)
			0.0200	0.0620			0.1440
			(0.0008)	(0.0024)			(0.0057)
F	21.000	21.021				21.062
ID 2	(0.8268)	(0.8276)				(0.8292)

Subtask 27-64-41-220-074-B

X. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
F	22.184	22.205			22.164
OD 3	(0.8734)	(0.8742)			(0.8726)
			0.0080	0.0410			0.0900
			(0.0003)	(0.0016)			(0.0035)
F	22.213	22.225				22.254
ID 6	(0.8745)	(0.8750)				(0.8761)

Subtask 27-64-41-220-075-A

Y. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
F	28.534	28.555			28.493
OD 4	(1.1234)	(1.1242)			(1.1218)
			0.0200	0.0620			0.1440
			(0.0008)	(0.0024)			(0.0057)
F	28.575	28.596				28.637
ID 5	(1.1250)	(1.1258)				(1.1274)

Subtask 27-64-41-220-076-A

Z. Dimensions of the Spoiler 1

NOTE: Limits on chrome plated items only apply when there is a layer of chrome remaining on the bearing surfaces.

(1) Complete an inspection of these dimensions.

FIG. DETAIL AND ITEM N°	ORIGINAL MANUFACTURING LIMITS	IN-SERVICE WEAR LIMITS
F	22.184	22.205			22.143
OD 3	(0.8734)	(0.8742)			(0.8718)
			0.0200	0.0620			0.1440
			(0.0008)	(0.0024)			(0.0057)
F	22.225	22.246				22.287
ID 4	(0.8750)	(0.8758)				(0.8774)

5. Close-up
Subtask 27-64-41-410-051-A

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the spoiler 1 (Ref. AMM TASK 27-64-41-400-001).

Subtask 27-64-41-942-053-A

B. Removal of Equipment
(1) Remove the safety barriers.
(2) Remove the WARNING NOTICE(S).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.03.31 23:55:30 UTC