DOC AIRBUS | AMM A320FReplacement of the Discharge Indicator Disc
TASK 26-22-43-960-001-A
Replacement of the Discharge Indicator Disc
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Expendable Parts
D. Referenced Information
3. Job Set-up
Subtask 26-22-43-010-050-A
Subtask 26-22-43-020-050-A
Subtask 26-22-43-942-051-A
[Rev.10 from 2021]
2026.04.01 06:43:59 UTC
Replacement of the Discharge Indicator Disc
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
FIN: 4035WM
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 4M (13 FT) |
| No specific | AR | BRUSH - BRISTLED, FIBER, SOFT |
| No specific | AR | BRUSH - BRISTLED, FIBER, STIFF |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.08BAA9) | Non Aqueous Cleaner-General - - |
| FIG.ITEM | DESIGNATION | IPC-CSN |
|---|---|---|
| 3 | DISC | AIPC 26-22-43-01-030 |
| 2 | PACKING | AIPC 26-22-43-01-040 |
| REFERENCE | DESIGNATION |
|---|---|
Discharge Indicator PRE VSB 18603-26-1Subtask 26-22-43-010-050-A
A. Get Access
(1) Put an ACCESS PLATFORM 4M (13 FT) in position under the discharge indicator assembly.
4. Procedure(1) Put an ACCESS PLATFORM 4M (13 FT) in position under the discharge indicator assembly.
Subtask 26-22-43-020-050-A
A. Replacement of the Discharge Indicator Disk
PRE VSB 18603-26-1
(1) Remove the snap ring (5) from the housing (1).
(2) Remove and discard the retainer (4) and the disc (3).
(3) Remove and discard the packing (2). Use a pointed plastic or wooden dowel to do this.
END OF PRE VSB 18603-26-1
POST VSB 18603-26-1
(4) Remove the snap ring (4) from the housing (1).
(5) Remove and discard the disc assembly (3).
(6) Remove and discard the packing (2). Use a pointed plastic or wooden dowel to do this.
END OF POST VSB 18603-26-1
Subtask 26-22-43-210-051-A PRE VSB 18603-26-1
(1) Remove the snap ring (5) from the housing (1).
(2) Remove and discard the retainer (4) and the disc (3).
(3) Remove and discard the packing (2). Use a pointed plastic or wooden dowel to do this.
END OF PRE VSB 18603-26-1
POST VSB 18603-26-1
(4) Remove the snap ring (4) from the housing (1).
(5) Remove and discard the disc assembly (3).
(6) Remove and discard the packing (2). Use a pointed plastic or wooden dowel to do this.
END OF POST VSB 18603-26-1
B. Preparation for Installation
(1) Make an inspection of the discharge indicator components.
(2) Loosen the unwanted material from the internal surfaces, shoulders and grooves of the housing (1) with a BRUSH - BRISTLED, FIBER, STIFF.
(3) Use a BRUSH - BRISTLED, FIBER, SOFT with Non Aqueous Cleaner-General - - (Material No.08BAA9) and clean all metallic parts. Pay special attention to the internal areas and grooves.
(4) Dry all parts fully with a clean, lint-free cloth.
Subtask 26-22-43-420-050-A (1) Make an inspection of the discharge indicator components.
(2) Loosen the unwanted material from the internal surfaces, shoulders and grooves of the housing (1) with a BRUSH - BRISTLED, FIBER, STIFF.
(3) Use a BRUSH - BRISTLED, FIBER, SOFT with Non Aqueous Cleaner-General - - (Material No.08BAA9) and clean all metallic parts. Pay special attention to the internal areas and grooves.
(4) Dry all parts fully with a clean, lint-free cloth.
C. Installation of the Discharge Indicator Disk
PRE VSB 18603-26-1
(1) Install the new AIPC 26-22-43-01-040 PACKING (2) in the internal face groove in the housing (1).
(2) Install and align the new AIPC 26-22-43-01-030 DISC (3) and the retainer (4) over the installed packing (2).
(3) Compress the retainer (4) onto the disc (3) and install the snap ring (5) in its groove.
END OF PRE VSB 18603-26-1
POST VSB 18603-26-1
(4) Install the new AIPC 26-22-43-01-040 PACKING (2) in the internal face groove in the housing (1).
(5) Install and align the new AIPC 26-22-43-01-030 DISC (3) over the installed packing (2).
(6) Compress the disc assembly (3) and install the snap ring (4) in its groove.
END OF POST VSB 18603-26-1
5. Close-upPRE VSB 18603-26-1
(1) Install the new AIPC 26-22-43-01-040 PACKING (2) in the internal face groove in the housing (1).
(2) Install and align the new AIPC 26-22-43-01-030 DISC (3) and the retainer (4) over the installed packing (2).
(3) Compress the retainer (4) onto the disc (3) and install the snap ring (5) in its groove.
END OF PRE VSB 18603-26-1
POST VSB 18603-26-1
(4) Install the new AIPC 26-22-43-01-040 PACKING (2) in the internal face groove in the housing (1).
(5) Install and align the new AIPC 26-22-43-01-030 DISC (3) over the installed packing (2).
(6) Compress the disc assembly (3) and install the snap ring (4) in its groove.
END OF POST VSB 18603-26-1
Subtask 26-22-43-942-051-A
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.