Inspection/Check of the Floatation and Survival Equipment

TASK 25-66-00-210-001-A
Inspection/Check of the Floatation and Survival Equipment

ZONE: 200
FIN: 7580MM ** ON A/C NOT FOR ALL
FIN: 7581MM ** ON A/C NOT FOR ALL
FIN: 7582MM ** ON A/C NOT FOR ALL
FIN: 7583MM
FIN: 7584MM
FIN: 7585MM ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
200	UPPER HALF FUSELAGE

3. Job Set-up
Subtask 25-66-00-010-050-A ** ON A/C NOT FOR ALL

A. Get Access
(1) Remove the packs that contain the life vests (7580MM, 7581MM, 7583MM, 7584MM, 7585MM, 7586MM) from:

below the passenger seats,
the cabin attendant seats,
the rear of the cockpit seats.

(2) Open the overhead stowage compartments and remove the DEMO life vests (7582MM).
(3) Open the overhead stowage compartments and remove the escape-slide raft survival-kits.

Subtask 25-66-00-010-050-B ** ON A/C NOT FOR ALL

A. Get Access
(1) Remove the packs that contain the life vests (7580MM, 7581MM, 7583MM, 7584MM, 7585MM, 7586MM) from:

below the passenger seats,
the cabin attendant seats,
the rear of the cockpit seats.

(2) Open the overhead stowage compartments and remove the DEMO life vests (7582MM).

4. Procedure
Subtask 25-66-00-210-051-A ** ON A/C NOT FOR ALL

A. Inspection:
(1) Visually examine the life vest transparent packs. Make sure that they are in a satisfactory condition.
(2) Make sure that you do not remove the life vests from the life vest transparent packs.
(3) Visually examine the spare life vests (if installed):
(a) Make sure that they are in a satisfactory condition.

NOTE: The servicing data is found on the life vest or on a service record card (the two which you can see through the transparent pack) or printed on the pack.

(b) Replace the life vests that are damaged and those that are in an unsatisfactory condition.
(4) Do an inspection of each escape slide raft survival kit (referred to as the kit) as follows:
(a) Remove the service history card from the kit pocket.
(b) Open the survival kit to examine the expiry date of the age limited module.
(c) Make sure that the expiry date of the age limited module is after the date of the next scheduled inspection which will occur within 3 years.
(d) If the service cycle is before the date of the next scheduled inspection, remove the kit from the aircraft and install the serviceable kit.

NOTE: The kit has a service cycle because some of the items have life limits.

(e) Put the service history card back into the kit pocket.
(f) If necessary, open the kit and do a check of the expiry date of the osmosis pump.

NOTE: The osmosis pump is not part of all kits. It depends on the P/N.

(g) Close the kit and safety it with lockwire and a lead safety seal.
(h) Do a check of the pack container for damage.
(i) Make sure that the lead safety seal and the lockwire that hold the zip fastener is in a good condition.
(j) Make sure the operating instructions placard is clean and you can easily read it. The placard is installed on the side of the kit.
(k) Examine the snap hook that attaches the pack to the kit attach loop on the escape slide raft girt.
(l) Make sure that the snap hook is not damaged or corroded and if you find it is in unsatisfactory condition, replace the kit.

Subtask 25-66-00-210-051-B ** ON A/C NOT FOR ALL

A. Inspection:
(1) Visually examine the life-vest transparent packs. Make sure that they are in a satisfactory condition.

NOTE: Do not remove the life vests from the packs.

(2) Visually examine the SPARE life vests:
(a) Make sure that they are in a satisfactory condition.

NOTE: The servicing data is found on the life-vest or on a service record card (both of which you can see through the transparent pack) or printed on the pack.

(b) Replace life vests that are damaged, and those that are in an unsatisfactory condition.

5. Close-up
Subtask 25-66-00-410-052-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Install the life vests (7580MM, 7581MM, 7583MM, 7584MM, 7585MM, 7586MM). Make sure that life vests are installed in all the required positions.
(2) Install the DEMO life vests (7582MM) in the overhead-stowage compartments and close the doors.
(3) Install the escape-slide raft survival-kits in the overhead-stowage compartments and close the doors.
(4) Make sure that the work area is clean and clear of tools and other items.

Subtask 25-66-00-410-052-B ** ON A/C NOT FOR ALL

A. Close Access
(1) Install the life vests (7580MM, 7581MM, 7583MM, 7584MM, 7585MM, 7586MM). Make sure that life vests are installed in all the required positions.
(2) Install the DEMO life vests (7582MM) in the overhead-stowage compartments and close the doors.
(3) Make sure that the work area is clean and clear of tools and other items.

[Rev.10 from 2021] 2026.04.01 06:32:42 UTC