Removal of Label, Stencil, Transfers or Decal Markings

TASK 11-24-71-000-802-A
Removal of Label, Stencil, Transfers or Decal Markings

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AFTER SHUTDOWN. THE ENGINE CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

1. Reason for the Job
Self Explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE
No specific	1	BRUSH - ACID
No specific	1	SPATULA - PLASTIC
No specific	AR	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.V01-201)	distilled or deionized water
(Material No.V01-438)	solvent
(Material No.V01-457)	solvent
(Material No.V02-050)	High temperature glass cloth tape
(Material No.V02-099)	lint free cloth
(Material No.V02-178)	masking tape
(Material No.V05-020)	waterproof silicon carbide
(Material No.09EBA1)	Methylene Chloride / Phenolic Stripper-General Use Process - -

3. Job Set-up
Subtask 11-24-71-941-052-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on ENG panel 115VU:
(a) Put a WARNING NOTICE(S) in position to tell persons not to start engine 1(2).
(2) On the ENG section of the maintenance panel 50VU:
(a) Make sure that the ON legend of the FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) in position to tell persons not to energize FADEC 1(2).

Subtask 11-24-71-010-053-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Put an ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE in position of the work area.
(2) Get access to the area where you must remove the label, stencil, transfer or decal markings.

Subtask 11-24-71-110-050-A ** ON A/C NOT FOR ALL

C. Cleaning of the Repair Area

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

(1) Clean the repair area with a clean lint free cloth (Material No.V02-099) and the solvent (Material No.V01-438) or solvent (Material No.V01-457) . Remove the solvent with a clean lint free cloth (Material No.V02-099) before the solvent becomes dry.

4. Procedure
Subtask 11-24-71-020-051-A ** ON A/C NOT FOR ALL

A. Removal of Label, Stencil, Transfer or Decal Markings

WARNING: WEAR APPLICABLE PERSONAL PROTECTIVE EQUIPMENT (PPE) WHEN YOU DO THIS TASK. BEFORE YOU USE PPE, READ, UNDERSTAND AND OBEY ALL INSTRUCTIONS FOR ITS USE. THESE INSTRUCTIONS INCLUDE INSTRUCTIONS FROM THE MANUFACTURER, YOUR EMPLOYER AND GOVERNMENT REGULATIONS. YOU CAN GET INJURED IF YOU DO NOT USE PPE. GET INSTRUCTIONS FROM YOUR EMPLOYER ON WHICH PPE IS NECESSARY.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

CAUTION: WEAR LINT FREE COTTON GLOVES WHEN YOU TOUCH THE CLEAN OR TREATED SURFACES. BARE HANDS CAN CAUSE CONTAMINATION.

CAUTION: DO NOT LET TURCO 5351 STRIPPER SOLUTION DRY ON THE SURFACE.

(1) Remove the marking with waterproof silicon carbide (Material No.V05-020) . If necessary, use a SPATULA - PLASTIC to remove the remaining marking.

NOTE: Do not remove the paint below the marking.

(2) If you cannot remove the marking easily do the following:
(a) Put High temperature glass cloth tape (Material No.V02-050) around the edge of the marking.
(b) Put 09EBA1Methylene Chloride / Phenolic Stripper-General Use Process - - on the surface of the marking with an BRUSH - ACID. Let the stripper solution stay on the surface for 15 to 20 minutes. Brush the stripper solution as necessary to let clean solution touch the marking.
(c) Apply more 09EBA1Methylene Chloride / Phenolic Stripper-General Use Process - - on the surface to loosen any remaining marking.
(d) Remove the 09EBA1Methylene Chloride / Phenolic Stripper-General Use Process - - from the surface with a clean lint free cloth (Material No.V02-099) wet with distilled or deionized water (Material No.V01-201) . Dry the area with a clean lint free cloth (Material No.V02-099) .
(e) Remove the masking tape (Material No.V02-178) .
(f) Clean the area with a clean lint free cloth (Material No.V02-099) made moist with solvent (Material No.V01-438) or solvent (Material No.V01-457) . Remove the solvent with a clean lint free cloth (Material No.V02-099) before solvent becomes dry.

[Rev.10 from 2021] 2026.03.31 22:54:12 UTC