DOC AIRBUS | AMM A320FApply Marking Paints with Stencils
TASK 11-00-00-370-003-A
Apply Marking Paints with Stencils
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Referenced Information
3. Job Set-up
Subtask 11-00-00-010-050-A
Subtask 11-00-00-370-052-A
Subtask 11-00-00-942-066-A
[Rev.10 from 2021]
2026.03.31 22:53:53 UTC
Apply Marking Paints with Stencils
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
1. Reason for the JobNOTE: This task is an alternative task for the external marking.
2. Job Set-up InformationA. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE |
| No specific | AR | BRUSH - BRISTLED |
| No specific | AR | FILM - MASKING |
| No specific | AR | TAPE - SELF-AMALGAMATING |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.04SBA3) | Varnish Polyurethane-Low VOC - External Structure |
| (Material No.08BAA9) | Non Aqueous Cleaner-General - - |
| (Material No.08BBD1) | Non Aqueous Cleaner-- Isopropyl Alcohol - |
| REFERENCE | DESIGNATION |
|---|---|
| SRM 512311 |
Subtask 11-00-00-010-050-A
A. Get Access
(1) Put an ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE in position in the work area.
Subtask 11-00-00-110-066-A (1) Put an ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE in position in the work area.
B. Cleaning of the external surfaces
(1) Clean the surface with Non Aqueous Cleaner-- Isopropyl Alcohol - (Material No.08BBD1) or Non Aqueous Cleaner-General - - (Material No.08BAA9) if the paint is fully cured, and let it dry.
4. Procedure(1) Clean the surface with Non Aqueous Cleaner-- Isopropyl Alcohol - (Material No.08BBD1) or Non Aqueous Cleaner-General - - (Material No.08BAA9) if the paint is fully cured, and let it dry.
Subtask 11-00-00-370-052-A
A. Apply Marking Paints with Stencils
(2) Refer to the supplier's instructions to mix the paint.
(3) Apply the paint as a spray or with a BRUSH - BRISTLED.
(a) For more information about the coatings SRM 512311.
Subtask 11-00-00-916-055-A NOTE: The base paint must be sufficiently dry (the paint manufacturer gives the indications "dry to tape" or "maskable drying time") before you apply the paint with a stencil.
(1) Put the FILM - MASKING or TAPE - SELF-AMALGAMATING in position. (2) Refer to the supplier's instructions to mix the paint.
(3) Apply the paint as a spray or with a BRUSH - BRISTLED.
(a) For more information about the coatings SRM 512311.
NOTE: Make sure that you keep the contrast between the color of the base paint and the marking.
(4) Remove all the masking material and touch up as necessary. B. Protection of External Markings
(1) When the paint is dry, apply Varnish Polyurethane-Low VOC - External Structure (Material No.04SBA3) if necessary.
5. Close-up(1) When the paint is dry, apply Varnish Polyurethane-Low VOC - External Structure (Material No.04SBA3) if necessary.
Subtask 11-00-00-942-066-A
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).