Application of Identification and Marking Paints

TASK 11-00-00-370-002-A
Application of Identification and Marking Paints

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	BRUSH - WIRE, ROTARY
No specific	AR	CLOTH-EMERY (GRADE 220 - 240)
No specific	AR	PAD - ABRASIVE
No specific	AR	PAD - NYLON ABRASIVE

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.04SBA3)	Varnish Polyurethane-Low VOC - External Structure
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

3. Job Set-up
Subtask 11-00-00-110-062-A

A. Cleaning of the External Surfaces
(1) Clean the surface with a Textile-Lint free Cotton - (Material No.14SBA1) soaked in Non Aqueous Cleaner-General - - (Material No.08BAA9) to remove all the signs of dirt.

NOTE: Do the cleaning operation until the cloth you use is clean.

Subtask 11-00-00-440-050-A

B. Surface Reactivation
(1) Before you apply the paint, make all the surfaces rough with PAD - NYLON ABRASIVE and Non Aqueous Cleaner-General - - (Material No.08BAA9) .

NOTE: Stop the reactivation procedure when the surface is sufficiently rough. Be careful not to remove or damage the protection of the skin or composite fibers.

NOTE: The surface on which you do the reactivation must be wet, but it is possible to rub a dry surface if a vacuum cleaning device is available to remove the dust when you have rubbed the surface.

(2) If necessary, remove the remaining sealant with CLOTH-EMERY (GRADE 220 - 240).
(3) Lightly rub the screw or rivet rows to remove all the black signs.
(4) Make the surface rough by hand:

for all the areas to which it is not possible to get access with the sanding machine
if there is a risk of damage when you use the machine (overlaping sheet metal junctions, window and windshield frames, antenna supports, fuselage area behind the radome).

(5) Use an BRUSH - WIRE, ROTARY to clean the areas with round head rivets.

Subtask 11-00-00-110-063-A

C. Final Cleaning and Wiping
(1) Rinse the surfaces you have rubbed with Non Aqueous Cleaner-General - - (Material No.08BAA9) then wipe with a Textile-Lint free Cotton - (Material No.14SBA1) before the cleaning agent evaporates.
(2) Lightly wipe again all the upper sections of the aircraft (fuselage above the windows, upper surface wings) with PAD - ABRASIVE before application of the wash primer.

4. Procedure
Subtask 11-00-00-370-050-A

A. Application of Identification and Marking Paints
(1) Apply a coat of paint and then a cross paint.

NOTE: The time between the last cleaning operation and the application of paint must not be more than 4 hours.

Subtask 11-00-00-916-053-A ** ON A/C NOT FOR ALL

B. Protection of exterior markings
(1) Apply a Varnish Polyurethane-Low VOC - External Structure (Material No.04SBA3) on all exterior functional and maintenance markings.

Subtask 11-00-00-916-053-B ** ON A/C NOT FOR ALL

B. Not Applicable

5. Close-up
Subtask 11-00-00-942-051-A

A. Clean the component interfaces and the adjacent area.

[Rev.10 from 2021] 2026.04.01 12:53:03 UTC