DOC AIRBUS | AMM A320FCheck of the Position of the Manual Handle of the Starter Air Control Valve after the Engine Start [PW11]
TASK 80-11-00-040-806-A
Check of the Position of the Manual Handle of the Starter Air Control Valve after the Engine Start
1. Reason for the Job
MMEL 80-07-01A
START VALVE POSITION INDICATION ON THE ENGINE SD PAGE
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 80-11-00-941-067-A ** ON A/C NOT FOR ALL
Subtask 80-11-00-040-056-A ** ON A/C NOT FOR ALL
Subtask 80-11-00-869-059-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 03:45:03 UTC
Check of the Position of the Manual Handle of the Starter Air Control Valve after the Engine Start
1. Reason for the Job
MMEL 80-07-01A
START VALVE POSITION INDICATION ON THE ENGINE SD PAGE
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | DRIVE 3/8 IN - SQUARE |
| No specific | 1 | EXTENSION |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 454 | HOT SECTION |
| 464 | HOT SECTION |
| REFERENCE | DESIGNATION |
|---|---|
Starter Air Control Valve Manual Override Access PortSubtask 80-11-00-941-067-A ** ON A/C NOT FOR ALL
A. Safety Precautions
(1) During the engine start procedure, obey all the engine safety precautions.
4. Procedure(1) During the engine start procedure, obey all the engine safety precautions.
Subtask 80-11-00-040-056-A ** ON A/C NOT FOR ALL
A. Check of the Position of the Manual Handle of the Starter Air Control Valve after the Engine Start
(1) Find the access port at the three o'clock position on the right thrust reverser inner fixed structure.
(2) Use the maintenance interphone jack (or an alternative) and make sure that you can communicate with the cockpit crew from the access port location.
(3) Find the 3/8 in. square drive (manual override drive) of the starter air control valve through the access port.
(4) Use a DRIVE 3/8 IN - SQUARE with a 31.5 in. (0.80 m) EXTENSION or more to turn the manual override drive.
(6) Tell the cockpit crew to make sure that on the ECAM WD, the warning message ENG 1(2) START VALVE FAULT/START VALVE NOT CLOSED does not come into view.
5. Close-up(1) Find the access port at the three o'clock position on the right thrust reverser inner fixed structure.
(2) Use the maintenance interphone jack (or an alternative) and make sure that you can communicate with the cockpit crew from the access port location.
(3) Find the 3/8 in. square drive (manual override drive) of the starter air control valve through the access port.
(4) Use a DRIVE 3/8 IN - SQUARE with a 31.5 in. (0.80 m) EXTENSION or more to turn the manual override drive.
NOTE: To close the square drive, it is necessary to turn it clockwise. To open the square drive, it is necessary to turn it counterclockwise.
(5) Make sure that the valve is in the closed position. NOTE: The valve is spring-loaded to the closed position.
(a) Make sure that you cannot rotate the square drive clockwise. (6) Tell the cockpit crew to make sure that on the ECAM WD, the warning message ENG 1(2) START VALVE FAULT/START VALVE NOT CLOSED does not come into view.
Subtask 80-11-00-869-059-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Make an entry in the logbook to record the check of the closed position of the starter manual handle.
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Make an entry in the logbook to record the check of the closed position of the starter manual handle.