Installation of the Centering Pins [CFMI]

TASK 78-36-41-400-042-A
Installation of the Centering Pins

FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 1M(3 FT)
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 140 and 122 lbf.in (1.58 and 1.38 m.daN )

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.CP2245)	finish paint EA4 blue 5991

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL

D. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-040-A	Opening of the Fan Cowl Doors
TASK 71-13-00-410-040-A	Closing of the Fan Cowl Doors
TASK 78-30-00-081-041-A	Make the Thrust Reverser Serviceable after Maintenance
TASK 78-30-00-481-041-A	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-36-00-010-040-A	Opening of the Thrust Reverser Doors
TASK 78-36-00-410-040-A	Closing of the Thrust Reverser Doors
Latches

3. Job Set-up
Subtask 78-36-41-860-055-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the ACCESS PLATFORM 1M(3 FT) is in position.

Subtask 78-36-41-010-077-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Make sure that the fan cowl doors are open (Ref. AMM TASK 71-13-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Make sure that the left thrust reverser cowl door is open (Ref. AMM TASK 78-36-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
451AL
(b) FOR [1000EM2] (ENGINE-2)
461AL

Subtask 78-36-41-040-068-A ** ON A/C NOT FOR ALL

C. Make sure that the thrust reverser is unserviceable (Ref. AMM TASK 78-30-00-481-041).

4. Procedure
Subtask 78-36-41-420-055-A ** ON A/C NOT FOR ALL

A. Installation of the Centering Pins

NOTE: Apply a witness line of finish paint EA4 blue 5991 (Material No.CP2245) on all nuts and connections when you have done the check of their torques.

(1) Install the centering pins and nuts.
(2) TORQUE nuts from to between 140 and 122 lbf.in (1.58 and 1.38 m.daN )

5. Close-up
Subtask 78-36-41-410-064-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the left thrust reverser cowl door (Ref. AMM TASK 78-36-00-410-040):
(a) FOR [1000EM1] (ENGINE-1)
451AL
(b) FOR [1000EM2] (ENGINE-2)
461AL

Subtask 78-36-41-440-058-A ** ON A/C NOT FOR ALL

B. Make the thrust reverser serviceable (Ref. AMM TASK 78-30-00-081-041).

Subtask 78-36-41-410-065-A ** ON A/C NOT FOR ALL

C. Close Access
(1) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Remove the access platform(s).
(3) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.02 07:42:11 UTC