Removal of the Upper Swivel Joints [CFMI]

TASK 78-31-49-000-017-A
Removal of the Upper Swivel Joints

WARNING: WEAR A FACE SHIELD WHICH IS RESISTANT TO HIGH PRESSURE JETS WHEN YOU WORK ON PRESSURIZED SYSTEMS.

WARNING: DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:

FLUSH IT AWAY WITH CLEAN WATER
GET MEDICAL AID.

CAUTION: USE TWO WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS:

ONE WRENCH TO HOLD THE UNION, AND
ONE TO LOOSEN OR TIGHTEN THE COUPLING NUT.

THIS PREVENTS DAMAGE TO THE PARTS.

CAUTION: MAKE SURE THERE IS NO UNWANTED MATERIAL IN THE PORTS AND ORIFICES OR DAMAGE CAN OCCUR.

CAUTION: YOU MUST INSTALL HYDRAULIC TUBES WITH HYDRAULIC FLUID AS LUBRICANT.

FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 1M(3 FT)
No specific	AR	CONTAINER 5 L (1.32 USGAL)
No specific	AR	PLUG - BLANKING
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 150 and 130 lbf.in (1.70 and 1.47 m.daN )
No specific	Torque wrench: range to between 260 and 235 lbf.in (2.94 and 2.66 m.daN )

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.CP2245)	finish paint EA4 blue 5991

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL, 452AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL, 462AR

D. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-040-A	Opening of the Fan Cowl Doors
TASK 78-30-00-481-041-A	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-36-00-010-040-A	Opening of the Thrust Reverser Doors
Forward Frame of the Half Door
Forward Frame of the Half Door
Supply Hoses and Pipes - Actuator Rod and Head
Supply Hoses and Pipes - Actuator Rod and Head

3. Job Set-up
Subtask 78-31-49-941-064-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

Subtask 78-31-49-010-068-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Open the fan cowl doors: (Ref. AMM TASK 71-13-00-010-040)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Put the ACCESS PLATFORM 1M(3 FT) in position.

Subtask 78-31-49-040-054-A ** ON A/C NOT FOR ALL

C. Make the thrust reverser unserviceable (Ref. AMM TASK 78-30-00-481-041)

Subtask 78-31-49-010-069-A ** ON A/C NOT FOR ALL

D. Open the thrust reverser doors: (Ref. AMM TASK 78-36-00-010-040)
(1) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL 462AR

Subtask 78-31-49-680-065-A ** ON A/C NOT FOR ALL

E. Drain of the Lower Rod.
(1) Put a CONTAINER 5 L (1.32 USGAL) under the lower blocker door actuator.

Forward Frame of the Half Door ** ON A/C NOT FOR ALL

(2) Disconnect the lower rod or head supply hose from the lower actuator and letthe hydraulic fluid drain completely.
(3) Reconnect the head supply hose on the actuator.

NOTE: You should apply a witness line of finish paint EA4 blue 5991 (Material No.CP2245) all nuts and connections when you have checked their torq ues.

(4) TORQUE nut to between 260 and 235 lbf.in (2.94 and 2.66 m.daN )

.
(5) Reconnect the rod supply hose on the actuator.
(6) TORQUE nut to between 150 and 130 lbf.in (1.70 and 1.47 m.daN )

(7) Remove the container.

4. Procedure
Subtask 78-31-49-020-062-A ** ON A/C NOT FOR ALL

A. Remove the Upper Swivel Joints.
(1) Loosen the bolt which attach the half clamps on the middle hydraulic line bracket, remove the other bolt.
(2) Remove the upper heat shield.
(3) Disconnect the upper swivel joint from the rod or head supply junction pipe.
(4) Remove and discard the preformed packing from the swivel joint.
(5) Disconnect the swivel joint from the rod or head supply hose.
(6) Remove the swivel joint.
(7) Put the PLUG-BLANKING in each disconnected line end.

[Rev.10 from 2021] 2026.04.02 06:38:04 UTC