Removal of the Lock-out Bolt Storage Bracket [CFMI]

TASK 78-31-49-000-016-A
Removal of the Lock-out Bolt Storage Bracket

WARNING: WEAR A FACE SHIELD WHICH IS RESISTANT TO HIGH PRESSURE JETS WHEN YOU WORK ON PRESSURIZED SYSTEMS.

WARNING: DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:

FLUSH IT AWAY WITH CLEAN WATER
GET MEDICAL AID.

CAUTION: USE TWO WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS:

ONE WRENCH TO HOLD THE UNION, AND
ONE TO LOOSEN OR TIGHTEN THE COUPLING NUT.

THIS PREVENTS DAMAGE TO THE PARTS.

CAUTION: MAKE SURE THERE IS NO UNWANTED MATERIAL IN THE PORTS AND ORIFICES OR DAMAGE CAN OCCUR.

CAUTION: YOU MUST INSTALL HYDRAULIC TUBES WITH HYDRAULIC FLUID AS LUBRICANT.

FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 1M(3 FT)
No specific	AR	CONTAINER 5 L (1.32 USGAL)
No specific	AR	WARNING NOTICE(S)
HIX3005	1	SAFETY SLEEVE - PIVOTING DOOR ACTUATOR

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL, 452AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-040-A	Opening of the Fan Cowl Doors
TASK 78-30-00-481-041-A	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-32-41-480-040-A	Installation of the Safety Sleeve on Blocker Door Actuator
TASK 78-32-41-860-040-A	Manual Deployment of the Blocker Door
TASK 78-36-00-010-040-A	Opening of the Thrust Reverser Doors
Hydraulic Line Brackets
Hydraulic Line Brackets

3. Job Set-up
Subtask 78-31-49-941-063-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

Subtask 78-31-49-010-067-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Open the fan cowl doors: (Ref. AMM TASK 71-13-00-010-040)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Put the ACCESS PLATFORM 1M(3 FT) in position.

Subtask 78-31-49-040-053-A ** ON A/C NOT FOR ALL

C. Make the thrust reverser unserviceable (Ref. AMM TASK 78-30-00-481-041)

Subtask 78-31-49-010-097-A ** ON A/C NOT FOR ALL

D. Open the thrust reverser doors: (Ref. AMM TASK 78-36-00-010-040)
(1) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL 462AR

Subtask 78-31-49-860-050-A ** ON A/C NOT FOR ALL

E. Manually bring the blocker door to deploy position (Ref. AMM TASK 78-32-41-860-040)

Subtask 78-31-49-480-050-A ** ON A/C NOT FOR ALL

F. Install the HIX3005 SAFETY SLEEVE - PIVOTING DOOR ACTUATOR on the blocker door actuator (Ref. AMM TASK 78-32-41-480-040)

4. Procedure
Subtask 78-31-49-020-061-A ** ON A/C NOT FOR ALL

A. Remove the Lock-out Bolt Storage Bracket.
(1) Remove bolts and nuts which attach storage bracket on forward frame.
(2) Remove the storage bracket.
(3) Put a CONTAINER 5 L (1.32 USGAL).
(4) Remove the container.

[Rev.10 from 2021] 2026.04.02 06:38:04 UTC