Installation of the Throttle Control Unit [IAE]

TASK 76-11-19-400-041-A
Installation of the Throttle Control Unit

FIN: 8KS1 ** ON A/C NOT FOR ALL
FIN: 8KS2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	AR	WARNING NOTICE(S)
98DNSA20206080	1	RIGGING PIN
98DNSA20208150	1	RIGGING PIN

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.05ABF1)	Retaining adhesive-Cylindrical fitting Medium strength Low viscosity -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
811

D. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
5	COTTER PIN	AIPC 76-11-01-02-010
8	COTTER PINS	AIPC 76-11-01-03-010

E. Referenced Information

REFERENCE	DESIGNATION
TASK 76-11-00-710-040-A	Operational Test of the Throttle Control Unit
TASK 76-11-00-820-040-A	Adjustment of the Mechanical Linkage
Throttle Control Unit - Access and Location
Throttle Control Unit - Removal/Installation
Throttle Control Unit - Rigging

3. Job Set-up
Subtask 76-11-19-860-050-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE is in position.
(4) Make sure that the access door 811 is open.
(5) Make sure that the throttle control levers are set to idle (0 deg.TLA).
(6) Make sure that the 98DNSA20208150 RIGGING PIN (13) is installed in the artificial feel unit of the throttle control.

Subtask 76-11-19-865-055-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B08
105VU	FLT CTL/SEC1/STBY SPLY	22CE	B01
121VU	FLIGHT CONTROLS/SEC3/SPLY	21CE3	Q19
121VU	FLIGHT CONTROLS/SEC2/SPLY	21CE2	Q18

Subtask 76-11-19-869-055-A ** ON A/C NOT FOR ALL

C. Make sure that the bush (3) is correctly bonded to the bolt (2).
(1) If necessary, bond the bush (3) to the bolt (2) with Retaining adhesive-Cylindrical fitting Medium strength Low viscosity - (Material No.05ABF1) .

4. Procedure
Subtask 76-11-19-420-052-B ** ON A/C NOT FOR ALL

A. Installation of the Throttle Control Unit.
(1) Remove all the blanking caps from the connectors.
(2) Install the throttle control unit 8KS1 (8KS2) (11) on its support.
(3) Install the three bolts (1) with the washers (10) and the nuts (9). Tighten the bolts (1).
(4) Install the three new AIPC 76-11-01-03-010 COTTER PINS (8)
(5) Engage the rod (4) in the fork of the throttle control unit (11).
(6) Attach the rod to the fork with the bolt (2) equipped with the bush (3), the washer (7) and the nut (6). Tighten the bolt.
(7) Connect the five electrical connectors (12). Tighten electrical connector fingertight plus one-eight turn using soft nose pliers.

Subtask 76-11-19-820-050-A ** ON A/C NOT FOR ALL

B. Make sure that you can easily install and remove the 98DNSA20206080 RIGGING PIN (14). If not adjust the rod (12) (Ref. AMM TASK 76-11-00-820-040)

Subtask 76-11-19-420-053-A ** ON A/C NOT FOR ALL

C. Install a new AIPC 76-11-01-02-010 COTTER PIN (5).

Subtask 76-11-19-080-050-A ** ON A/C NOT FOR ALL

D. Remove the 98DNSA20208150 RIGGING PIN (13) from the artificial feel unit.

Subtask 76-11-19-869-062-A ** ON A/C NOT FOR ALL

E. Check of the Throttle Control Unit installation
(1) With the throttle control lever in idle position:
(a) Move the thrust reverser control lever to the full reverse position, then back to the idle position. Make sure that there are no hard and/or blocking points over the full travel range.

Subtask 76-11-19-865-056-A ** ON A/C NOT FOR ALL

F. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B08
105VU	FLT CTL/SEC1/STBY SPLY	22CE	B01
121VU	FLIGHT CONTROLS/SEC3/SPLY	21CE3	Q19
121VU	FLIGHT CONTROLS/SEC2/SPLY	21CE2	Q18

Subtask 76-11-19-710-051-A ** ON A/C NOT FOR ALL

G. Do an operational test of the throttle control unit (Ref. AMM TASK 76-11-00-710-040)

5. Close-up
Subtask 76-11-19-410-052-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the access door 811
(3) Remove the WARNING NOTICE(S).
(4) Remove the access platform(s).

[Rev.10 from 2021] 2026.04.01 03:15:48 UTC