DOC AIRBUS | AMM A320FRemoval of the Fan Outlet Guide Vane (OGV) and/or OGV Seal [CFMI]
TASK 72-23-00-000-001-A
Removal of the Fan Outlet Guide Vane (OGV) and/or OGV Seal
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 72-23-00-941-051-A ** ON A/C NOT FOR ALL
Subtask 72-23-00-020-050-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.02 06:33:41 UTC
Removal of the Fan Outlet Guide Vane (OGV) and/or OGV Seal
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | ACCESS PLATFORM 1M(3 FT) |
| No specific | AR | WARNING NOTICE(S) |
| 856A2795 | 1 | PULLER,PLUGS-OGV |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| FOR [1000EM1] (ENGINE-1) | |
| 437AL, 438AR, 451AL, 452AR | |
| FOR [1000EM2] (ENGINE-2) | |
| 447AL, 448AR, 461AL, 462AR | |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 71-13-00-010-040-A | Opening of the Fan Cowl Doors |
| TASK 78-30-00-481-041-A | Make the Thrust Reverser Unserviceable for Maintenance |
| TASK 78-36-00-010-040-A | Opening of the Thrust Reverser Doors |
Removal and Installation of the Fan Outlet Guide VaneSubtask 72-23-00-941-051-A ** ON A/C NOT FOR ALL
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
Subtask 72-23-00-010-051-A ** ON A/C NOT FOR ALL (1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
B. Get Access
(1) Open the fan cowls: (Ref. AMM TASK 71-13-00-010-040)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Put an ACCESS PLATFORM 1M(3 FT) in position.
Subtask 72-23-00-040-053-A ** ON A/C NOT FOR ALL Subtask 72-23-00-010-070-A ** ON A/C NOT FOR ALL (1) Open the fan cowls: (Ref. AMM TASK 71-13-00-010-040)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Put an ACCESS PLATFORM 1M(3 FT) in position.
D. Open the thrust reverser doors: (Ref. AMM TASK 78-36-00-010-040)
(1) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL 462AR
4. Procedure(1) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL 462AR
Subtask 72-23-00-020-050-A ** ON A/C NOT FOR ALL
A. Removal of the Fan Outlet Guide Vane and/or Seal
PRE SB 72-097 (aluminum OGV)
(1) Remove the 4 plugs (30) with the 856A2795 PULLER,PLUGS-OGV (P01).
(2) Remove the 4 bolts (40) which attach the 2 lateral outer fairings (50).
POST SB 72-097 (composite OGV)
(3) Remove the 2 plugs (30) with the 856A2795 PULLER,PLUGS-OGV (P01).
(4) Remove the 2 bolts (40) and washers (45) which attach the OGV outer platform.
END OF SB 72-097
PRE SB 72-097 (aluminum OGV)
(5) Remove the 2 lateral outer fairings (50).
POST SB 72-097 (composite OGV)
(6) Not applicable
PRE SB 72-097 (aluminium OGV)
(7) Lower the OGV (10) inner platform down into the aft fairing recess.
(8) Move the OGV (10) outer platform rearward at an angle, disengage the outer platform and remove the vane.
POST SB 72-097 (composite OGV)
(9) Lower the OGV (10) inner platform down into the OGV support aft fairing recess (see arrow circled one).
(10) Move the OGV (10) outer platform forward at an angle (see arrow circled two)
disengage the outer platform from the fan case and remove the composite OGV.
PRE SB 72-097 (aluminum OGV)
(11) Remove the OGV seal (20).
POST SB 72-097 (aluminum OGV)
(12) Not applicable
END OF SB 72-097
PRE SB 72-097 (aluminum OGV)
(1) Remove the 4 plugs (30) with the 856A2795 PULLER,PLUGS-OGV (P01).
(2) Remove the 4 bolts (40) which attach the 2 lateral outer fairings (50).
POST SB 72-097 (composite OGV)
(3) Remove the 2 plugs (30) with the 856A2795 PULLER,PLUGS-OGV (P01).
(4) Remove the 2 bolts (40) and washers (45) which attach the OGV outer platform.
END OF SB 72-097
PRE SB 72-097 (aluminum OGV)
(5) Remove the 2 lateral outer fairings (50).
POST SB 72-097 (composite OGV)
(6) Not applicable
PRE SB 72-097 (aluminium OGV)
(7) Lower the OGV (10) inner platform down into the aft fairing recess.
(8) Move the OGV (10) outer platform rearward at an angle, disengage the outer platform and remove the vane.
POST SB 72-097 (composite OGV)
(9) Lower the OGV (10) inner platform down into the OGV support aft fairing recess (see arrow circled one).
(10) Move the OGV (10) outer platform forward at an angle (see arrow circled two)
disengage the outer platform from the fan case and remove the composite OGV.
PRE SB 72-097 (aluminum OGV)
(11) Remove the OGV seal (20).
POST SB 72-097 (aluminum OGV)
(12) Not applicable
END OF SB 72-097