Removal of the Core Fire Detector Channel B Wire Harness [CFMB]

TASK 71-52-43-000-043-A
Removal of the Core Fire Detector Channel B Wire Harness

FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	AR	CAP - BLANKING
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL, 452AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors
TASK 78-30-00-481-041-B	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-36-00-010-040-B	Opening of the Thrust Reverser Doors
Fire Detector Channel B Wire Harness

3. Job Set-up
Subtask 71-52-43-860-056-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(b) Put a WARNING NOTICE(S) in position to tell persons that both thrust reverser control lever are not operational.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

Subtask 71-52-43-865-059-A ** ON A/C NOT FOR ALL

WARNING: OPEN THE PROBE HEATER CIRCUIT-BREAKERS 1DA1(2), 3DA1(2,3), 4DA1(2,3) AND 5DA1(2,3) BEFORE ENG1(2)FADEC A and EIU 1(2) C/B'S 2KS1 AND 2KS2. IF YOU DO NOT OBEY THIS SEQUENCE:

THE PROBES WILL BECOME TOO HOT.
THIS CAN CAUSE DAMAGE TO EQUIPMENT AND INJURY TO MAINTENANCE PERSONNEL.

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	COM/CVR/SPLY	2RK	E14
49VU	COM/CVR/CTL	4RK	E13
** ON A/C NOT FOR ALL
49VU	ENGINE/2/FIRE DET/LOOP B	8WD2	A07
49VU	ENGINE/1/FIRE DET/LOOP A	7WD1	A06
49VU	ENGINE/2/FADEC A/AND EIU 2	2KS2	A05
49VU	ENGINE/1/FADEC A/AND EIU 1	2KS1	A04
49VU	ENGINE/1 AND 2/IGN/SYS A	1JH	A03
49VU	ANTI ICE/PROBES/AOA/1	4DA1	D04
49VU	ANTI ICE/PROBES/PITOT/1	3DA1	D02
49VU	NAV PROBES/ADIRU 1/AND AOA 1/26VAC	5FP1	F07
49VU	NAV PROBES/ADIRU1/115VAC	4FP1	F06
** ON A/C NOT FOR ALL
49VU	ANTI ICE/RAIN/RPLNT/CAPT	1DB1	D01
** ON A/C NOT FOR ALL
49VU	COM/CVR/SPLY	23RK	E14
49VU	COM/CVR/CTL	26RK	E13
** ON A/C NOT FOR ALL
105VU	ADIRS/ADIRU1/28VDC	6FP1	C02
121VU	RCDR/DFDR	7TU	K16
121VU	ENGINE/ENG2/OIL/PRESS	2EN2	N42
121VU	ENGINE/ENG2/OIL/QTY	1EN2	N41
121VU	ENGINE/ENG1/OIL/PRESS	2EN1	N40
121VU	ENGINE/ENG1/OIL/QTY	1EN1	N39
121VU	ADIRS/ADIRU/2/26VAC AND AOA	5FP2	N08
121VU	ADIRS/ADIRU/3/26VAC AND AOA	5FP3	N07
121VU	ADIRS/ADIRU/2/115VAC	4FP2	N06
121VU	ADIRS/ADIRU/3/115VAC	4FP3	N05
121VU	ADIRS/ADIRU/2/28VDC	6FP2	N04
121VU	ADIRS/ADIRU/3/28VDC	6FP3	N03
121VU	ENGINE/IGN/ENG2/SYS B	3JH2	P42
121VU	ENGINE/IGN/ENG1/SYS B	3JH1	P41
121VU	ENGINE/IGN/ENG2/SYS A BAT	2JH2	P40
121VU	ENGINE/IGN/ENG1/SYS A BAT	2JH1	P39
121VU	ENGINE/ENG1 AND 2 FIRE EXTIG/BTL1/SQUIB/B	2WE1	Q44
121VU	ENGINE/ENG1 AND 2 FIRE EXTIG/BTL1/SQUIB/A	1WE1	Q43
121VU	ENGINE/ENG1 AND 2 FIRE EXTIG/BTL2/SQUIB/B	2WE2	Q42
121VU	ENGINE/ENG1 AND 2 FIRE EXTIG/BTL2/SQUIB/A	1WE2	Q41
121VU	ENGINE/ENG2/FADEC B	4KS2	Q40
121VU	ENGINE/ENG2/FIRE DET/LOOP A	7WD2	Q39
121VU	ENGINE/ENG1/FIRE DET/LOOP B	8WD1	Q38
121VU	ENGINE/ENG1/FADEC B/AND EIU 1	4KS1	R41
122VU	ELEC/GCU/2	2XU2	T27
122VU	ELEC/GCU/1	2XU1	T26
122VU	ANTI ICE/PROBES/2/TAT	1DA2	Y15
122VU	ANTI ICE/PROBES/2/PITOT	3DA2	Y14
122VU	ANTI ICE/PROBES/2/AOA	4DA2	Y13
122VU	ANTI ICE/PROBES/2/STATIC	5DA2	Y11
122VU	ANTI ICE/PROBES/3/PITOT	3DA3	Z16
122VU	ANTI ICE/PROBES/3/AOA	4DA3	Z15
122VU	ANTI ICE/PROBES/3/STATIC	5DA3	Z14
122VU	ANTI ICE/PROBES/1/STATIC	5DA1	Z13
122VU	ANTI ICE/PROBES/1/TAT	1DA1	Z12
** ON A/C NOT FOR ALL
122VU	ANTI ICE/RAIN/RPLNT/F/O	1DB2	W11

Subtask 71-52-43-865-095-A ** ON A/C NOT FOR ALL

WARNING: OPEN THE PROBE HEATER AND WINDOW HEATER CIRCUIT-BREAKERS BEFORE YOU OPEN THE PHC AND WHC CIRCUIT BREAKERS. IF YOU DO NOT OBEY THIS SEQUENCE:

THE PROBES WILL BECOME TOO HOT.
THIS CAN CAUSE DAMAGE TO EQUIPMENT AND INJURY TO MAINTENANCE PERSONNEL.

C. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	ANTI ICE/PROBES/PHC/1	2DA1	D03
122VU	ANTI ICE/WHC/2	5DG2	W13
122VU	ANTI ICE/WHC/1	5DG1	X13
122VU	ANTI ICE/PROBES/PHC/3	2DA3	Y16
122VU	ANTI ICE/PROBES/PHC/2	2DA2	Y12

Subtask 71-52-43-010-060-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-040):
(2) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(3) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(4) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position.

Subtask 71-52-43-040-056-A ** ON A/C NOT FOR ALL

E. Make the thrust reverser unserviceable (Ref. AMM TASK 78-30-00-481-041).

Subtask 71-52-43-010-059-A ** ON A/C NOT FOR ALL

F. Open the thrust reverser doors (Ref. AMM TASK 78-36-00-010-040):
(1) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL 462AR

4. Procedure
Subtask 71-52-43-020-056-B ** ON A/C NOT FOR ALL

A. Removal of the Channel B Fire Detector Harness Assembly (4205KS)

Fire Detector Channel B Wire Harness ** ON A/C NOT FOR ALL

(1) Disconnect the electrical connector 454VC-A from the core junction box.
(2) Remove the two bolts (5) and open the two clamps (10) that attach the harnesses to the pylon. Remove the harness 4205KS from the clamps. Install the bolt (5) and tighten it with your hand.
(3) Remove the bolt (15) and open the clamp (20) that attaches the harness assemblies to the bracket at station 233. Remove harness 4205KS from the clamp. Install the bolt (15) and tighten it with your hand.
(4) Remove the bolt (15) and open the clamp (25), attached to the bracket at station 233, and remove the harness 4205KS.
(5) Remove the three bolts (15) and the three clamps (30) that attach the harness 4205KS to the brackets at station 239.
(6) Cut the lockwire and remove the the screws (60) and the clamp (55) that attach the harness 4205KS to the fire detector element 4001WD2-A.
(7) Remove the nut (45) that attaches the wire (50) to terminal A of the fire detector.
(8) Remove the nut (75) that attaches the wire (70) to terminal C of the fire detector.
(9) Remove the nut (95), the washers (90), the lockwasher (85), and the bolt (80) that attach the ground wire (65) to the bracket.
(10) Remove the harness assembly 4205KS from the engine.
(11) Put CAP - BLANKING on the electrical connectors.

[Rev.10 from 2021] 2026.04.02 06:32:27 UTC