Removal of the Flap Attachment Bearing

TASK 57-53-21-000-001-A
Removal of the Flap Attachment Bearing

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:

DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.

1. Reason for the Job
Self Explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 3M (10 FT)
No specific	AR	SAFETY BARRIER(S)
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	1	WARNING NOTICE(S)
98D27507541000	1	WRENCH - BEARING, FLAP TO CARRIAGE, TRACK 2, 3 AND 4
98D27803500001	1	LOCKING TOOL ZERO POS
98D57004034000	1	REM-INST. TOOL - FLAP BEARING
98D57004050000	1	SPANNER FLAP TRACK 2 AND 3 BEARING

B. Referenced Information

REFERENCE	DESIGNATION
TASK 27-54-62-000-001-A	Removal of the Outboard Flap
TASK 27-54-62-000-002-A	Removal of the Outboard Double-Slotted Flap
Flap Attachment Bearing - Location and Detail ** ON A/C NOT FOR ALL
Flap Attachment Bearing - Location and Detail ** ON A/C NOT FOR ALL
Flap Attachment Bearing - Location and Detail ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 57-53-21-941-050-A

A. Safety Precautions
(1) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
(2) Install the 98D27803500001 LOCKING TOOL ZERO POS on the slat/flap control lever.
(3) Put WARNING NOTICE(S) in position to tell persons not to operate the slat/flap system.

Subtask 57-53-21-865-050-A

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B07
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B02
** ON A/C ALL
121VU	FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2	8CV	Q21

Subtask 57-53-21-010-050-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT) in position below the applicable outboard flap at zone 533 (633).
(2) Remove the applicable outboard flap (Ref. AMM TASK 27-54-62-000-001).

Subtask 57-53-21-010-050-B ** ON A/C NOT FOR ALL

C. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT) in position below the applicable outboard flap at zone 533 (633).
(2) Remove the applicable outboard flap (Ref. AMM TASK 27-54-62-000-002).

4. Procedure

CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:

DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.

Subtask 57-53-21-020-050-C ** ON A/C NOT FOR ALL

A. Removal of the Flap Attachment Bearing

Flap Attachment Bearing - Location and Detail ** ON A/C NOT FOR ALL

(1) For track 3, do the steps that follow:
(a) Release the lockwasher (7).
(b) Use the 98D57004050000 SPANNER FLAP TRACK 2 AND 3 BEARING to remove the locknut (6). Discard the locknut (6).
(c) Remove and discard the lockwasher (7).
(d) Release the tab-washer (2) and remove the screw (1).
(e) Remove and discard the tab-washer (2).
(f) Remove the locking device (3).
(g) Remove and discard the spherical bearing (4).
(2) For track 4, do the steps that follow:
(a) Release the lockwasher (10).
(b) Use the 98D57004034000 REM-INST. TOOL - FLAP BEARING to remove the locknut (9). Discard the locknut (9).

NOTE: The 98D27507541000 WRENCH - BEARING, FLAP TO CARRIAGE, TRACK 2, 3 AND 4 can be used as an alternative tool for track 4.

(c) Remove and discard the lockwasher (10).
(d) Release the tab-washer (14) and remove the screw (13).
(e) Remove and discard the tab-washer (14).
(f) Remove the locking device (12).
(g) Remove and discard the spherical bearing (11).

Subtask 57-53-21-020-050-D ** ON A/C NOT FOR ALL

A. Removal of the Flap Attachment Bearing.

Flap Attachment Bearing - Location and Detail ** ON A/C NOT FOR ALL

(1) For track 3, do the steps that follow:
(a) Release the lockwasher (6).
(b) Use the 98D57004050000 SPANNER FLAP TRACK 2 AND 3 BEARING to remove the locknut (7).

NOTE: The 98D27507541000 WRENCH - BEARING, FLAP TO CARRIAGE, TRACK 2, 3 AND 4 can be used as an alternative tool for track 3.

(c) Remove and discard the lockwasher (6).
(d) Remove the nut (8).
(e) Remove the bolt (1), the washer (2) and the rotation-lock (3).
(f) Remove the spherical bearing (4) from the structure (5).
(2) For track 4, do the steps that follow:
(a) Release the lockwasher (14).
(b) Use the 98D57004034000 REM-INST. TOOL - FLAP BEARING to remove the locknut (15).

NOTE: The 98D27507541000 WRENCH - BEARING, FLAP TO CARRIAGE, TRACK 2, 3 AND 4 can be used as an alternative tool for track 4.

(c) Remove and discard the lockwasher (14).
(d) Remove the nut (16).
(e) Remove the bolt (9), the washer (10) and the rotation-lock (11).
(f) Remove the spherical bearing (12) from the structure (13).

Subtask 57-53-21-020-050-E ** ON A/C NOT FOR ALL

A. Removal of the Flap Attachment Bearing.

Flap Attachment Bearing - Location and Detail ** ON A/C NOT FOR ALL

(1) For track 3, do the steps that follow:
(a) Release the lockwasher (6).
(b) Use the 98D57004050000 SPANNER FLAP TRACK 2 AND 3 BEARING to remove the locknut (7).

NOTE: The 98D27507541000 WRENCH - BEARING, FLAP TO CARRIAGE, TRACK 2, 3 AND 4 can be used as an alternative tool for track 3.

NOTE: The 98D27507541000 WRENCH - BEARING, FLAP TO CARRIAGE, TRACK 2, 3 AND 4 can be used as an alternative tool for track 4.

[Rev.10 from 2021] 2026.04.02 06:31:24 UTC