Special Detailed Inspection (Endoscope) of Outboard Double Slotted Flap, Rib 2, 9 and 12, LH/RH

TASK 57-53-00-220-020-A
Special Detailed Inspection (Endoscope) of Outboard Double Slotted Flap, Rib 2, 9 and 12, LH/RH

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:

DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.

CAUTION: DO NOT APPLY TEMPORARY PROTECTION SYSTEM (TPS) ON THE INSPECTION AREA. IF YOU APPLY TPS ON THE INSPECTION AREA, YOU CAN CAUSE DAMAGE TO THE AIRCRAFT.

ZONE: 587
ZONE: 687

1. Reason for the Job
Refer to the MPD TASK: 575343-01
SPECIAL DETAILED INSPECTION (ENDOSCOPE) OF OUTBOARD DOUBLE-SLOTTED FLAP, RIB 2, 9 AND 12, LH/RH

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	AR	LIGHT SOURCE - SPARK-PROOF
No specific	AR	SAFETY BARRIER(S)
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.05RAB9)	Adhesive Film Tape-- Aluminium Foil -
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
587	FLAP N° 2
687	FLAP N° 2

D. Referenced Information

REFERENCE	DESIGNATION
TASK 27-50-00-866-008-A	Extension of the Flaps on the Ground
TASK 27-50-00-866-008-A-01	Extension of the Flaps/Slats on the Ground
TASK 27-50-00-866-009-A	Retraction of the Flaps on the Ground
TASK 27-50-00-866-009-A-01	Retraction of the Flaps/Slats on the Ground
TASK 51-78-00-916-001-A	Application of Temporary Protection System (TPS)
SRM 575300	(for corrective action)
NTM 575343	(for corrective action)
Outboard Flap - Ribs 2,9 and 12 - Inspection Area

3. Job Set-up
Subtask 57-53-00-941-094-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) Put a WARNING NOTICE(S) on the flap/slat control lever (panel 114VU) to tell persons not to operate the flaps.
(2) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.

Subtask 57-53-00-860-078-A ** ON A/C NOT FOR ALL

B. Aircraft Maintenance Configuration

WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

(1) Fully extend the flaps (Ref. AMM TASK 27-50-00-866-008).
(2) Make sure that the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION is installed on the flap/slat control lever on the panel 114VU.

Subtask 57-53-00-865-135-A ** ON A/C NOT FOR ALL

C. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B07
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B02
** ON A/C NOT FOR ALL
121VU	FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2	8CV	Q21

Subtask 57-53-00-010-088-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position below the applicable rib at zone 587(687).
(2) Put the LIGHT SOURCE - SPARK-PROOF adjacent to the inspection area.
(3) Remove and discard the cover from the inspection hole adjacent to each of the ribs to be inspected.
(4) Make sure that the inspection hole is clear of unwanted material.

Subtask 57-53-00-110-092-A ** ON A/C NOT FOR ALL

E. Preparation for Inspection

CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:

DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.

(1) Make sure that the inspection area is sufficiently clean to do the inspection of the area.
(2) Use a clean Textile-Lint free Cotton - (Material No.14SBA1) , made moist with Non Aqueous Cleaner-General - - (Material No.08BAA9) to clean:

the outboard double slotted flap, Rib 2, 9 and 12, LH/RH.

(3) Make sure that there is no TPS layer and if there is a TPS layer, remove it (Ref. AMM TASK 51-78-00-916-001).

4. Procedure
Subtask 57-53-00-280-067-A ** ON A/C NOT FOR ALL

A. Special Detailed Inspection (Endoscope) of Outboard Double Slotted Flap, Rib 2, 9 and 12, LH/RH
(1) Do a special detailed internal inspection of rib 2, 9 and 12, in the outboard flap LH/RH. Refer to NTM 575343, for the inspection procedure.

NOTE: If necessary, refer to the SRM 575300 for the correct repair procedure. If the defect is not included in this repair, you must request a procedure from AIRBUS.

5. Close-up
Subtask 57-53-00-410-087-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Remove the spark-proof lamp from the inspection area.
(2) Use Adhesive Film Tape-- Aluminium Foil - (Material No.05RAB9) , cut to the correct dimensions, to make new covers for the inspection holes.
(3) Install the new covers on the inspection holes.
(4) Make sure that the work area is clean and clear of tool(s) and other items.

Subtask 57-53-00-865-136-A ** ON A/C NOT FOR ALL

B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B07
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B02
** ON A/C NOT FOR ALL
121VU	FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2	8CV	Q21

Subtask 57-53-00-860-079-A ** ON A/C NOT FOR ALL

C. Aircraft Maintenance Configuration
(1) Remove the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION from the flap/slat control lever.
(2) Fully retract the flaps (Ref. AMM TASK 27-50-00-866-009).

Subtask 57-53-00-942-091-A ** ON A/C NOT FOR ALL

D. Removal of Equipment
(1) Remove the access platform(s).
(2) Remove the safety barriers.
(3) Remove the WARNING NOTICE(S).
(4) Make sure that the work area is clean and clear of tools and other items.

[Rev.10 from 2021] 2026.04.02 06:31:23 UTC