DOC AIRBUS | AMM A320FDetailed Inspection of Outboard Flap, Support at Track 4, including RIB14, Fitting Assembly, Pendulum Support and Attachment Structure ....
TASK 57-53-00-200-011-A
Detailed Inspection of Outboard Flap, Support at Track 4, including RIB14, Fitting Assembly, Pendulum Support and Attachment Structure ....
Refer to the MPD TASK: 575313-01
DETAILED INSPECTION OF OUTBOARD FLAP, SUPPORT AT TRACK 4, INCLUDING RIB 14, FITTING ASSEMBLY, PENDULUM SUPPORT AND ATTACHMENT STRUCTURE, INTERNAL AND EXTERNAL, LH/RH
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Referenced Information
3. Job Set-up
Subtask 57-53-00-941-079-A ** ON A/C NOT FOR ALL
Subtask 57-53-00-210-067-A ** ON A/C NOT FOR ALL
Subtask 57-53-00-410-067-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.02 06:31:21 UTC
Detailed Inspection of Outboard Flap, Support at Track 4, including RIB14, Fitting Assembly, Pendulum Support and Attachment Structure ....
WARNING:
MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
WARNING:
PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
CAUTION:
BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
- DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
- DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
- MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
CAUTION:
DO NOT APPLY TEMPORARY PROTECTION SYSTEM (TPS) ON THE INSPECTION AREA. IF YOU APPLY TPS ON THE INSPECTION AREA, YOU CAN CAUSE DAMAGE TO THE AIRCRAFT.
1. Reason for the JobRefer to the MPD TASK: 575313-01
DETAILED INSPECTION OF OUTBOARD FLAP, SUPPORT AT TRACK 4, INCLUDING RIB 14, FITTING ASSEMBLY, PENDULUM SUPPORT AND ATTACHMENT STRUCTURE, INTERNAL AND EXTERNAL, LH/RH
NOTE: The effectivity of this task is ALL. To know if this task is applicable for your aircraft, refer to the MPD task applicability and the weight variant data given in the SRM introduction.
2. Job Set-up InformationA. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE |
| No specific | AR | SAFETY BARRIER(S) |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| No specific | AR | WARNING NOTICE(S) |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.08BAA9) | Non Aqueous Cleaner-General - - |
| (Material No.14SBA1) | Textile-Lint free Cotton - |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 587 | FLAP N° 2 |
| 687 | FLAP N° 2 |
| 533AT, 533CB, 633AT, 633CB |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 27-50-00-866-008-A | Extension of the Flaps on the Ground |
| TASK 27-50-00-866-008-A-01 | Extension of the Flaps/Slats on the Ground |
| TASK 27-50-00-866-009-A | Retraction of the Flaps on the Ground |
| TASK 27-50-00-866-009-A-01 | Retraction of the Flaps/Slats on the Ground |
| TASK 27-54-62-000-003-A | Removal of the Leading Edge Panels 2 and 5 on the Outboard Flap |
| TASK 27-54-62-400-003-A | Installation of the Leading Edge Panels 2 and 5 on the Outboard Flap |
| TASK 51-78-00-916-001-A | Application of Temporary Protection System (TPS) |
| TASK 57-55-11-000-001-A | Removal of the Flap Track Fairings Nos. 2, 3 and 4 |
| TASK 57-55-11-400-001-A | Installation of the Flap Track Fairings Nos. 2, 3 and 4 |
| SRM 575321 | (for corrective action) |
Outboard FlapSubtask 57-53-00-941-079-A ** ON A/C NOT FOR ALL
A. Safety Precautions
(1) Put WARNING NOTICE(S) in the cockpit to tell persons not to operate the flaps or slats.
(2) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
Subtask 57-53-00-860-117-A ** ON A/C NOT FOR ALL (1) Put WARNING NOTICE(S) in the cockpit to tell persons not to operate the flaps or slats.
(2) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
B. Aircraft Maintenance Configuration
(2) Make sure that the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION is on the slat/flap control lever.
Subtask 57-53-00-865-097-A ** ON A/C NOT FOR ALL WARNING:
MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
(1) Fully extend the flaps (Ref. AMM TASK 27-50-00-866-008). (2) Make sure that the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION is on the slat/flap control lever.
C. Open, safety and tag this(these) circuit breaker(s):
Subtask 57-53-00-010-068-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 | 6CV | B07 |
| 121VU | FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 | 8CV | Q21 |
D. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE below the applicable wing trailing edge at flap track 4, zone 533 (633).
(2) Remove the applicable access panels (Ref. AMM TASK 57-55-11-000-001):
(3) Remove the outboard flap leading edge panel 5 (Ref. AMM TASK 27-54-62-000-003).
Subtask 57-53-00-010-068-C ** ON A/C NOT FOR ALL (1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE below the applicable wing trailing edge at flap track 4, zone 533 (633).
(2) Remove the applicable access panels (Ref. AMM TASK 57-55-11-000-001):
(3) Remove the outboard flap leading edge panel 5 (Ref. AMM TASK 27-54-62-000-003).
D. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE below the applicable wing trailing edge at flap track 4, zone 533 (633).
(2) Remove the applicable access panels (Ref. AMM TASK 57-55-11-000-001):
Subtask 57-53-00-110-067-A ** ON A/C NOT FOR ALL (1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE below the applicable wing trailing edge at flap track 4, zone 533 (633).
(2) Remove the applicable access panels (Ref. AMM TASK 57-55-11-000-001):
E. Preparation for Inspection
(2) Use a Textile-Lint free Cotton - (Material No.14SBA1) , made moist with Non Aqueous Cleaner-General - - (Material No.08BAA9) to clean the external surfaces of:
4. ProcedureCAUTION:
BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
(1) Make sure that the inspection area is sufficiently clean to do the inspection of the area. - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
- DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
- MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
(2) Use a Textile-Lint free Cotton - (Material No.14SBA1) , made moist with Non Aqueous Cleaner-General - - (Material No.08BAA9) to clean the external surfaces of:
- the outboard flap upper and lower skins
- the attachment fitting.
Subtask 57-53-00-210-067-A ** ON A/C NOT FOR ALL
A. Detailed Inspection of Outboard Flap, Support at Track 4, including RIB14, Fitting Assembly, Pendulum Support and Attachment Structure Internal and External, LH/RH
(1) Make a detailed inspection of:
5. Close-up(1) Make a detailed inspection of:
- the external parts of the pendulum support that you can see
- the lower skin around the pendulum support. Make sure the inner and outer doubler is fully inspected.
- there is no corrosion
- there are no cracks
- the surface protection is in the correct condition.
NOTE: If necessary, refer to the SRM 575321 for the correct repair procedure.
Subtask 57-53-00-410-067-A ** ON A/C NOT FOR ALL
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the leading edge panel 5 (Ref. AMM TASK 27-54-62-400-003).
(3) Install the applicable access panels (Ref. AMM TASK 57-55-11-400-001):
Subtask 57-53-00-410-067-C ** ON A/C NOT FOR ALL (1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the leading edge panel 5 (Ref. AMM TASK 27-54-62-400-003).
(3) Install the applicable access panels (Ref. AMM TASK 57-55-11-400-001):
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the applicable access panels (Ref. AMM TASK 57-55-11-400-001):
Subtask 57-53-00-865-098-A ** ON A/C NOT FOR ALL (1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the applicable access panels (Ref. AMM TASK 57-55-11-400-001):
B. Make sure that this(these) circuit breaker(s) is(are) closed:
Subtask 57-53-00-860-118-A ** ON A/C NOT FOR ALL Subtask 57-53-00-942-073-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 | 6CV | B07 |
| 121VU | FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 | 8CV | Q21 |
D. Removal of Equipment
(1) Remove the WARNING NOTICE(S).
(2) Remove the access platform(s).
(3) Remove the safety barriers.
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(1) Remove the WARNING NOTICE(S).
(2) Remove the access platform(s).
(3) Remove the safety barriers.
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.