Reactivation of the Wing-Tip Fence

TASK 57-31-00-440-001-A
Reactivation of the Wing-Tip Fence

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 534
ZONE: 634

1. Reason for the Job
CDL 57-01
Wing Tip Fence
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 4M (13 FT)
No specific	AR	SAFETY BARRIER(S)
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)
98D27803500001	1	LOCKING TOOL ZERO POS

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
534	WING TIP
634	WING TIP

D. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 33-41-00-710-001-A	Operational Test of the Navigation Lights
TASK 33-48-00-710-002-A	Operational Test of the Anti-Collision/Strobe Lighting
TASK 57-31-22-000-001-A	Removal of the Wing-Tip Fence
TASK 57-31-22-400-001-A	Installation of the Wing-Tip Fence

3. Job Set-up
Subtask 57-31-00-860-051-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Make sure that the aircraft electrical circuits are energized
(Ref. AMM TASK 24-41-00-861-002).

Subtask 57-31-00-941-050-A ** ON A/C NOT FOR ALL

B. Safety Precautions
(1) Install the 98D27803500001 LOCKING TOOL ZERO POS on the flap/slat control lever.
(2) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
(3) Put WARNING NOTICE(S) in the cockpit to tell persons not to operate the flaps or slats.
(4) Put an ACCESS PLATFORM 4M (13 FT) in position below the applicable wing-tip:

for the left wing, below zone 534
for the right wing, below zone 634.

Subtask 57-31-00-865-052-A ** ON A/C NOT FOR ALL

C. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
122VU	LIGHTING/EXT LT/NAV1/AND LOGO/LT	1LA	T03
** ON A/C NOT FOR ALL
122VU	LIGHTING/EXT LT/NAV2/AND LOGO/LT	2LA	T02
122VU	LIGHTING/WING/STROBE	10LV	V05
** ON A/C NOT FOR ALL
122VU	LIGHT/EXT LT NAV1/AND LOGO/LT	1LA	T03

4. Procedure
Subtask 57-31-00-440-050-A ** ON A/C NOT FOR ALL

A. Reactivation of the Wing-Tip Fence
(1) Reactivation of a wing-tip fence that was not fully removed:
(a) Remove the damaged wing-tip fence (Ref. AMM TASK 57-31-22-000-001).
(b) Install a new wing-tip fence (Ref. AMM TASK 57-31-22-400-001).
(c) Write down in the aircraft log that the wing-tip fence has been reactivated.
(2) Reactivation of a wing-tip fence that was removed:
(a) Remove the aluminium foil adhesive tape from the wing tip.
(b) Clean the wing tip with a Textile-Lint free Cotton - (Material No.14SBA1) made moist with Non Aqueous Cleaner-General - - (Material No.08BAA9) .
(c) Install a new wing-tip fence (Ref. AMM TASK 57-31-22-400-001).

5. Close-up
Subtask 57-31-00-865-053-A ** ON A/C NOT FOR ALL

A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
122VU	LIGHTING/EXT LT/NAV1/AND LOGO/LT	1LA	T03
** ON A/C NOT FOR ALL
122VU	LIGHTING/EXT LT/NAV2/AND LOGO/LT	2LA	T02
122VU	LIGHTING/WING/STROBE	10LV	V05
** ON A/C NOT FOR ALL
122VU	LIGHT/EXT LT NAV1/AND LOGO/LT	1LA	T03

Subtask 57-31-00-710-050-A ** ON A/C NOT FOR ALL

B. Operational Test
(1) Do an operational test of the navigation lights (Ref. AMM TASK 33-41-00-710-001).
(2) Do an operational test of the anti-collision/strobe lighting (Ref. AMM TASK 33-48-00-710-002).

Subtask 57-31-00-942-050-A ** ON A/C NOT FOR ALL

C. Removal of Equipment
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).
(3) Remove the safety barriers.
(4) Remove the WARNING NOTICE(S).
(5) Remove the 98D27803500001 LOCKING TOOL ZERO POS from the flap/slat control lever.
(6) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

Subtask 57-31-00-860-052-A ** ON A/C NOT FOR ALL

D. Aircraft Maintenance Configuration
(1) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.02 06:30:54 UTC