W DOC AIRBUS | AMM A320F

Removal of the Access Cover 148AZ or/and the ACT-Equipment Support Door

TASK 57-17-11-000-001-A-01
Removal of the Access Cover 148AZ or/and the ACT-Equipment Support Door

WARNING: MAKE SURE THAT YOU HAVE THE CORRECT FIRE FIGHTING EQUIPMENT AVAILABLE.
WARNING: OBEY THE SAFETY PROCEDURES WHEN YOU DO WORK IN A FUEL TANK.
WARNING: BE CAREFUL NOT TO GET AIRCRAFT FUEL IN YOUR MOUTH OR IN YOUR EYES. IF YOU GET FUEL ON YOUR SKIN OR ON YOUR CLOTHES, FLUSH IT IMMEDIATELY WITH WATER. IF NECESSARY, GET MEDICAL HELP. AIRCRAFT FUEL IS POISONOUS.
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
ZONE: 147
ZONE: 148
1. Reason for the Job
NOTE: This task is applicable for aircraft with Additional Center Tank.
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific
AR
SAFETY BARRIER(S)
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
147
MAIN GEAR WELL AND HYDRAULIC COMPARTMENT
148
MAIN GEAR WELL AND HYDRAULIC COMPARTMENT
734, 744
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 28-00-00-910-001-A
Fuel Safety Procedures
TASK 28-10-00-910-001-A
Safety Procedures When You Do Work in a Fuel Tank
TASK 28-25-00-650-001-A
Pressure Defuel
TASK 28-25-00-650-003-A
To Drain Remaining Fuel from the Wing Tanks and the Center Tank
TASK 28-25-00-650-003-A-01
To Drain Remaining Fuel from the Wing Tanks and the Center Tank
TASK 28-25-00-869-001-A
Fuel Transfer
TASK 28-28-11-000-001-A
Removal of the ACT Fuel Transfer-Pump Pressure-Switch
TASK 28-28-31-000-001-A
Removal of the ACT Fuel-Transfer-Pump Mounting-Plate
TASK 28-28-33-000-001-A
Removal of the ACT Fuel Transfer-Valve
TASK 32-12-00-410-001-A
Close the Main Gear Doors after Access
TASK 57-17-11-000-003-A
Removal of the Protective Cover of the ACT-Equipment Support Door
F Illustration of the Access Cover 148AZ
F Warning Placards on the Center Wing BOX ** ON A/C NOT FOR ALL
F ACT-Equipment Support Door
3. Job Set-up
Subtask 57-17-11-010-057-A
A. Get Access
   (1) Open the Main Landing Gear (MLG) door 734 ( 744 and install the safety devices (Ref. AMM TASK 32-12-00-410-001).
   (2) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position at zone 147 or 148.
   (3) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
Subtask 57-17-11-650-059-A
B. Aircraft Maintenance Configuration
   (1) Obey the fuel safety procedures (Ref. AMM TASK 28-00-00-910-001), (Ref. AMM TASK 28-10-00-910-001).
   (2) Defuel the center tank (Ref. AMM TASK 28-25-00-650-001) or move the fuel into a different tank (Ref. AMM TASK 28-25-00-869-001).
   (3) Drain the remaining fuel in the center tank (Ref. AMM TASK 28-25-00-650-003).
Subtask 57-17-11-865-063-A
C. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C ALL
49VUFUEL/X FEED/VALVE/MOT12QEA12
** ON A/C NOT FOR ALL
121VUFUEL/CTR TK/PUMP2 SPLY30QAP26
121VUFUEL/CTR TK/PUMP1 SPLY29QAP23
** ON A/C ALL
121VUFUEL/RFL/DFL/SPLY2QUL24
121VUFUEL/RFL/DFL/XFR/DEFUEL/VALVE1QUL23
121VUFUEL/L WING TK/PUMP2 SPLY7QAN26
121VUFUEL/L WING TK/PUMP1 SPLY1QAN23
121VUFUEL/R WING TK/PUMP2 SPLY8QAQ26
121VUFUEL/R WING TK/PUMP1 SPLY2QAQ23
4. Procedure
Subtask 57-17-11-020-057-A ** ON A/C NOT FOR ALL
A. Removal of the Access Cover 148AZ
F Illustration of the Access Cover 148AZ ** ON A/C NOT FOR ALL
   (1) Remove the bolt (13), the washer (14) and disconnect the bonding strip (15).
   (2) Remove the screws (16), the washers (17) and the washers (18).
   (3) Remove the access cover (11).
NOTE: Hold the access cover (11) in position when you remove the fasteners.
   (4) Remove and discard the seal (12).
Subtask 57-17-11-020-057-B ** ON A/C NOT FOR ALL
A. Removal of the Access Cover 148AZ
F Illustration of the Access Cover 148AZ ** ON A/C NOT FOR ALL
WARNING: MAKE SURE THAT THE WARNING/CAUTION PLACARDS ARE INSTALLED AND YOU CAN EASILY READ THEM. THESE PLACARDS TELL PERSONS THAT THERE IS A POSSIBLE LOW OXYGEN CONTENT IN:
  • THE AREA BEHIND THE ACCESS PANEL(S)
  • THE ADJACENT AREAS WHEN THE ACCESS PANEL(S) IS(ARE) OPEN.
IF THE PLACARDS ARE DAMAGED, MISSING OR PAINTED OVER, YOU MUST REPLACE THEM. THESE PLACARDS ARE RELATED TO A CRITICAL DESIGN CONFIGURATION CONTROL LIMITATION (CDCCL).
   (1) Do a visual inspection to look for placards that are:
  • Damaged
  • Missing
  • Painted over.
   (2) Make sure that you can easily read the placard message.
F Warning Placards on the Center Wing BOX ** ON A/C NOT FOR ALL
   (3) If the placards are damaged, missing, painted over or you cannot easily read them, replace them at the next maintenance opportunity.
   (4) Remove the bolt (13), the washer (14) and disconnect the bonding strip (15).
   (5) Remove the screws (16), the washers (17) and the washers (18).
   (6) Remove the access cover (11).
NOTE: Hold the access cover (11) in position when you remove the fasteners.
   (7) Remove and discard the seal (12).
Subtask 57-17-11-020-058-A ** ON A/C NOT FOR ALL
B. Removal of the ACT-Equipment Support Door
F ACT-Equipment Support Door ** ON A/C NOT FOR ALL
   (1) Remove the protective cover (Ref. AMM D/O 57-17-11-00).
   (2) Remove the following components:
   (3) Remove the screw (27), the washer (26), the bonding strip (25) and disconnect the bonding strip (28).
   (4) Remove the screw (30), the washer (32) and disconnect the bonding strip (29).
   (5) Remove the screw (39), the washer (40) and disconnect the bonding strip (38).
   (6) Remove the screw (36), the washer (35), the bonding strip (38) and disconnect the bonding strip (37).
   (7) Remove the bolts (21), the washers (22), the washers (23) and the fittings (24), (31) and (41).
   (8) Remove the ACT-equipment support door (34).
NOTE: Hold the ACT-equipment support door (34) in position when you remove the bolts (21).
   (9) Remove and discard the seal (33).
Subtask 57-17-11-020-058-C ** ON A/C NOT FOR ALL
B. Removal of the ACT-Equipment Support Door
F ACT-Equipment Support Door ** ON A/C NOT FOR ALL
WARNING: MAKE SURE THAT THE WARNING/CAUTION PLACARDS ARE INSTALLED AND YOU CAN EASILY READ THEM. THESE PLACARDS TELL PERSONS THAT THERE IS A POSSIBLE LOW OXYGEN CONTENT IN:
  • THE AREA BEHIND THE ACCESS PANEL(S)
  • THE ADJACENT AREAS WHEN THE ACCESS PANEL(S) IS(ARE) OPEN.
IF THE PLACARDS ARE DAMAGED, MISSING OR PAINTED OVER, YOU MUST REPLACE THEM. THESE PLACARDS ARE RELATED TO A CRITICAL DESIGN CONFIGURATION CONTROL LIMITATION (CDCCL).
   (1) Do a visual inspection to look for placards that are:
  • Damaged
  • Missing
  • Painted over.
   (2) Make sure that you can easily read the placard message.
F Warning Placards on the Center Wing BOX ** ON A/C NOT FOR ALL
   (3) If the placards are damaged, missing, painted over or you cannot easily read them, replace them at the next maintenance opportunity.
   (4) Remove the protective cover (Ref. AMM D/O 57-17-11-00).
   (5) Remove the following components:
   (6) Remove the screw (27), the washer (26), the bonding strip (25) and disconnect the bonding strip (28).
   (7) Remove the screw (30), the washer (32) and disconnect the bonding strip (29).
   (8) Remove the screw (39), the washer (40) and disconnect the bonding strip (38).
   (9) Remove the screw (36), the washer (35), the bonding strip (38) and disconnect the bonding strip (37).
   (10) Remove the bolts (21), the washers (22), the washers (23) and the fittings (24), (31) and (41).
   (11) Remove the ACT-equipment support door (34).
NOTE: Hold the ACT-equipment support door (34) in position when you remove the bolts (21).
   (12) Remove and discard the seal (33).
Subtask 57-17-11-020-058-K ** ON A/C NOT FOR ALL
B. Removal of the ACT-Equipment Support Door
F ACT-Equipment Support Door ** ON A/C NOT FOR ALL
WARNING: MAKE SURE THAT THE WARNING/CAUTION PLACARDS ARE INSTALLED AND YOU CAN EASILY READ THEM. THESE PLACARDS TELL PERSONS THAT THERE IS A POSSIBLE LOW OXYGEN CONTENT IN:
  • THE AREA BEHIND THE ACCESS PANEL(S)
  • THE ADJACENT AREAS WHEN THE ACCESS PANEL(S) IS(ARE) OPEN.
IF THE PLACARDS ARE DAMAGED, MISSING OR PAINTED OVER, YOU MUST REPLACE THEM. THESE PLACARDS ARE RELATED TO A CRITICAL DESIGN CONFIGURATION CONTROL LIMITATION (CDCCL).
   (1) Do a visual inspection to look for placards that are:
  • Damaged
  • Missing
  • Painted over.
   (2) Make sure that you can easily read the placard message.
F Warning Placards on the Center Wing BOX ** ON A/C NOT FOR ALL
   (3) If the placards are damaged, missing, painted over or you cannot easily read them, replace them at the next maintenance opportunity.
   (4) Remove the protective cover (Ref. AMM TASK 57-17-11-000-003).
   (5) Remove the following components:
   (6) Remove the screw (27), the washer (26), the bonding strip (25) and disconnect the bonding strip (28).
   (7) Remove the screw (30), the washer (32) and disconnect the bonding strip (29).
   (8) Remove the screw (39), the washer (40) and disconnect the bonding strip (38).
   (9) Remove the screw (36), the washer (35), the bonding strip (38) and disconnect the bonding strip (37).
   (10) Remove the bolts (21), the washers (22), the washers (23) and the fittings (24), (31) and (41).
   (11) Remove the ACT-equipment support door (34).
NOTE: Hold the ACT-equipment support door (34) in position when you remove the bolts (21).
   (12) Remove and discard the seal (33).
[Rev.8 from Aug 2017] 2026.04.02 06:30:34 UTC
"WTRUIB" 2025