Removal of the Sliding Window Panel

TASK 56-12-11-000-002-A
Removal of the Sliding Window Panel

WARNING: YOU MUST MAKE SURE THAT YOU CAN HOLD THE COMPONENT BEFORE YOU REMOVE/INSTALL IT. THE COMPONENT IS HEAVY. IF IT FALLS, IT CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.

CAUTION: DO NOT USE SHARP AND/OR METALLIC TOOLS OR OBJECTS TO REMOVE/INSTALL THE WINDSHIELD OR A WINDOW. DO NOT USE A LEVER AGAINST THE EDGE OF THE WINDSHIELD OR WINDOW. IF YOU DO NOT OBEY THESE INSTRUCTIONS, YOU WILL CAUSE DAMAGE TO THE WINDSHIELD OR WINDOW.

CAUTION: BEFORE YOU INSTALL/REMOVE THE GSE-TOOL, READ THE INSTRUCTIONS IN THE APPLICABLE GSE INSTRUCTION MANUAL. WHILE YOU OPERATE THIS TOOL, CAREFULLY OBEY THEM. IF YOU DO NOT OBEY THE INSTRUCTIONS, DAMAGE TO EQUIPMENT CAN OCCUR.

ZONE: 211
ZONE: 212
FIN: 8DG1
FIN: 8DG2

1. Reason for the Job

NOTE: Two persons are necessary for this procedure.

NOTE: There are alternative procedures for the removal of the sliding windows. This task gives one of the procedures. For the other procedures, refer to the related task in this page block.

NOTE: This procedure is applicable to:

The acrylic windows (GKN supplier, P/N NH...)
The glass windows (PPG supplier, P/N NP...)
The glass windows (SGS supplier, P/N SPSA320-7-X-X or SPSA320-8-X-X, do not include P/N SPSA320-3-X-X or SPSA320-4-X-X).

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
No specific	AR	CAP - BLANKING
No specific	AR	CUP - SUCTION
No specific	AR	PIN DIA 5 MM (0.196 IN), LENGTH 50 MM (1.96 IN.)
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
98D56103002000	1	WRENCH, REMOVAL - SLIDING WINDOW OF LUCAS AND PPG

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
211	COCKPIT
212	COCKPIT

C. Referenced Information

REFERENCE	DESIGNATION
TASK 25-13-41-000-803-A	Removal of the Personal Tablet Support
TASK 33-12-12-000-002-A	Removal of the Map Table Lights
TASK 33-12-12-000-003-A	Removal of the Reading Light
TASK 33-12-12-000-804-A	Removal of the Map Table Light
TASK 33-12-18-000-001-A	Removal of the Map Table Light Rheostats
TASK 33-12-18-000-802-A	Removal of the Map-Table Light Control-Box
TASK 46-26-22-000-001-A	Removal of the EFB Display Unit (DU)
TASK 46-26-22-000-002-A	Removal of the EFB Display Unit (DU) Mounting Bracket
TASK 56-12-11-000-803-C	Removal of the Structural Bracket Assembly
TASK 56-12-11-010-001-A	Opening of the Cockpit Sliding Windows
Sliding Window Lining
Sliding Window Panel (GKN and PPG suppliers, P/N NP..., do not include P/Ns NP165332A1 and NP165332A2)
Sliding Window Panel (SGS Supplier)
Sliding Window Panel (PPG supplier, P/Ns NP165332A1 and NP165332A2)

3. Job Set-up
Subtask 56-12-11-941-061-A

A. Get Access
(1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position at zone 210, in front of the sliding window.

Subtask 56-12-11-865-053-A

WARNING: MAKE SURE THAT THE CIRCUIT BREAKERS RELATED TO THE WEATHER RADAR ARE OPENED, SAFETIED AND TAGGED.

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
121VU	COM NAV/RADAR/1	5SQ1	K13
** ON A/C NOT FOR ALL
121VU	COM NAV/RADAR/2	5SQ2	K14
** ON A/C ALL
FOR FIN: 8DG1 (WINDOWSLIDING, L)
122VU	ANTI ICE/WINDOWS/L	4DG1	X14
122VU	ANTI ICE/WHC/1	5DG1	X13
123VU	ANTI ICE/L/WHSLD	1DG1	AF10
FOR FIN: 8DG2 (WINDOWSLIDING, R)
122VU	ANTI ICE/WINDOWS/R	4DG2	W14
122VU	ANTI ICE/WHC/2	5DG2	W13
123VU	ANTI ICE/R/WHSLD	1DG2	AF03

Subtask 56-12-11-020-052-A ** ON A/C NOT FOR ALL

C. Removal of the Component
(1) Remove the reading light bulb from the sliding window lining, if installed (Ref. AMM TASK 33-12-12-000-001):
(a) FOR [8DG1] (WINDOW-SLIDING, L)

25LE.

(b) FOR [8DG2] (WINDOW-SLIDING, R)

26LE.

(2) Remove the personal tablet support, if installed (Ref. AMM D/O 25-13-41-00).
(3) Remove the Electronic Flight Bag (EFB) Display Unit (DU), if installed (Ref. AMM D/O 46-26-22-00).
(4) Remove the EFB DU mounting-bracket, if installed (Ref. AMM D/O 46-26-22-00).

Subtask 56-12-11-020-052-C ** ON A/C NOT FOR ALL

C. Removal of the Component
(1) Remove the map table light installed on the sliding window lining (Ref. AMM TASK 33-12-12-000-002):
(a) FOR [8DG1] (WINDOW-SLIDING, L)
- 41LE.
(b) FOR [8DG2] (WINDOW-SLIDING, R)
- 42LE.
(2) Remove the map-table light rheostats installed on the sliding window lining (Ref. AMM TASK 33-12-18-000-001):
(a) FOR [8DG1] (WINDOW-SLIDING, L)
- 39LE.
(b) FOR [8DG2] (WINDOW-SLIDING, R)
- 40LE.
(3) Remove the personal tablet support, if installed (Ref. AMM D/O 25-13-41-00).
(4) Remove the EFB DU, if installed (Ref. AMM TASK 46-26-22-000-001).
(5) Remove the EFB DU mounting-bracket, if installed (Ref. AMM TASK 46-26-22-000-002).

Subtask 56-12-11-020-052-D ** ON A/C NOT FOR ALL

C. Removal of the Component
(1) Remove the map table light installed on the sliding window lining (Ref. AMM TASK 33-12-12-000-804):
(a) FOR [8DG1] (WINDOW-SLIDING, L)
- 41LE.
(b) FOR [8DG2] (WINDOW-SLIDING, R)
- 42LE.
(2) Remove the map-table light rheostats installed on the sliding window lining (Ref. AMM TASK 33-12-18-000-802):
(a) FOR [8DG1] (WINDOW-SLIDING, L)
- 53LE.
(b) FOR [8DG2] (WINDOW-SLIDING, R)
- 54LE.
(3) Remove the personal tablet support, if installed (Ref. AMM TASK 25-13-41-000-803).
(4) Remove the EFB DU, if installed (Ref. AMM TASK 46-26-22-000-001).
(5) Remove the EFB DU mounting-bracket, if installed (Ref. AMM TASK 46-26-22-000-002).

Subtask 56-12-11-020-053-B

D. Removal of the Sliding Window Lining

Sliding Window Lining

(1) Open sliding window 8DG1 (8DG2) (Ref. AMM TASK 56-12-11-010-001).
(2) Remove the screw (5) and the pencil holder assembly (7).
(3) Remove the screw (21) and the washer (20).
(4) Remove the screw (19) and the washer (18).
(5) Remove the handle (6).
(6) Remove the screw (9) and the washer (8).
(7) Remove the screw (15) and the washer (14).
(8) Remove the guide (13).
(9) Close the sliding window.
(10) Remove the blanking plug (4), the screw (3) and the washer (2).
(11) Remove the screws (11) and (12).
(12) Lift the plate (17).
(13) Remove the sliding window lining (16).
(14) Disconnect the electrical connector (10) from the receptacle.
(15) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(16) Remove the structural bracket assembly, if installed (Ref. AMM TASK 56-12-11-000-803).

4. Procedure
Subtask 56-12-11-020-054-A

A. Removal of the Sliding Window Panel
(1) Remove the acrylic sliding-window panel (GKN supplier, P/N NH...) and the glass sliding-window panel (PPG supplier, P/N NP..., do not include P/Ns NP165332A1 and NP165332A2):

Sliding Window Panel (GKN and PPG suppliers, P/N NP..., do not include P/Ns NP165332A1 and NP165332A2)

NOTE: Numbers 1 to 63 identify the attachment holes on the periphery of the sliding panel (31).

(a) Open the sliding window.
(b) Loosen the nuts (30) (do not include the nuts at positions 17 and 18).
(c) Hold the nuts (30) with the 98D56103002000 WRENCH, REMOVAL - SLIDING WINDOW OF LUCAS AND PPG (98D56103002200) and (98D56103002201) at positions 17 and 18 and loosen the screws (32).
(d) Remove the nuts (30) and the screws (32) at positions 28 and 60.
(e) Installation of the pins:
1 For the glass sliding-windows panel (PPG supplier, P/N NP..., do not include P/Ns NP165332A1 and NP165332A2), install the PIN DIA 5 MM (0.196 IN), LENGTH 50 MM (1.96 IN.) at positions 28 and 60 to hold the sliding window panel (31) in position.
2 For the acrylic sliding-windows panel (GKN supplier, P/N NH...), install the PIN DIA 5 MM (0.196 IN), LENGTH 50 MM (1.96 IN.) at positions 28 and 60 to hold the sliding window panel (31) in position.
(f) Remove the remaining nuts (30) and screws (32).
(g) Close the sliding window.
(h) Use the CUP - SUCTION to hold and move the sliding window panel (31).
(i) Remove the two locating pins at positions 28 and 60.
(j) Remove the sliding window panel (31).
(k) Move the frame of the sliding window to the open position (the sliding window panel (31) stays in position in its housing).
(l) Carefully remove the sliding window panel (31).
(2) Remove the glass sliding-window panel (SGS supplier, P/N SPSA320-7-X-X or SPSA320-8-X-X):

Sliding Window Panel (SGS Supplier)

NOTE: Numbers 1 to 63 identify the attachment holes on the periphery of the sliding window panel (32).

(a) Open the sliding window.
(b) Loosen the screws (30).
(c) Use the CUP - SUCTION to hold and move the sliding window panel (32).
(d) Hold the sliding window panel (32) in position then remove and discard the screws (30) and the washers (31).
(e) Move the frame of the sliding window to the open position (the sliding window panel (32) stays in position in its housing).
(f) Carefully remove the sliding window panel (32).
(3) Remove the glass sliding-window panel (PPG supplier, P/Ns NP165332A1 and NP165332A2):

Sliding Window Panel (PPG supplier, P/Ns NP165332A1 and NP165332A2)

NOTE: Numbers 1 to 63 identify the attachment holes on the periphery of the sliding window panel (1).

(a) Open the sliding window.
(b) Loosen the screws (3).
(c) Use the CUP - SUCTION to hold and move the sliding window panel (1).
(d) Hold the sliding window panel (1) in position and remove the screws (3) and the washers (2).
(e) Move the frame of the sliding window to the open position.
(f) Make sure that the sliding window panel (1) stays in position in its housing.
(g) Carefully remove the sliding window panel (1).

[Rev.10 from 2021] 2026.04.01 02:07:20 UTC