W DOC AIRBUS | AMM A320F

Removal of the Sliding Window Panel

TASK 56-12-11-000-002-A-01
Removal of the Sliding Window Panel

WARNING: YOU MUST MAKE SURE THAT YOU CAN HOLD THE COMPONENT BEFORE YOU REMOVE/INSTALL IT. THE COMPONENT IS HEAVY. IF IT FALLS, IT CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
CAUTION: DO NOT USE SHARP AND/OR METALLIC TOOLS OR OBJECTS TO REMOVE/INSTALL THE WINDSHIELD OR A WINDOW. DO NOT USE A LEVER AGAINST THE EDGE OF THE WINDSHIELD OR WINDOW. IF YOU DO NOT OBEY THESE INSTRUCTIONS, YOU WILL CAUSE DAMAGE TO THE WINDSHIELD OR WINDOW.
CAUTION: BEFORE YOU INSTALL/REMOVE THE GSE-TOOL, READ THE INSTRUCTIONS IN THE APPLICABLE GSE INSTRUCTION MANUAL. WHILE YOU OPERATE THIS TOOL, CAREFULLY OBEY THEM. IF YOU DO NOT OBEY THE INSTRUCTIONS, DAMAGE TO EQUIPMENT CAN OCCUR.
ZONE: 211
ZONE: 212
FIN: 8DG1
FIN: 8DG2
1. Reason for the Job
NOTE: Two persons are necessary for this procedure.
NOTE: There are alternative procedures for the removal of the sliding windows. This task gives one of the procedures. For the other procedures, refer to the related task in this page block.
NOTE: This procedure is applicable to the glass windows (SGS supplier, P/N SPSA320-3-X-X or SPSA320-4-X-X).
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
No specific
AR
CAP - BLANKING
No specific
AR
CUP - SUCTION
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
98D56103002001
1
WRENCH, REMOVAL - SLIDING WINDOW OF SPS
 B. Consumable Materials
REFERENCE
DESIGNATION
(Material No.08BAA9)
Non Aqueous Cleaner-General - -
(Material No.14SBA1)
Textile-Lint free Cotton -
 C. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
211
COCKPIT
212
COCKPIT
 D. Referenced Information
REFERENCE
DESIGNATION
TASK 25-13-41-000-803-A
Removal of the Personal Tablet Support
TASK 33-12-12-000-002-A
Removal of the Map Table Lights
TASK 33-12-12-000-003-A
Removal of the Reading Light
TASK 33-12-12-000-804-A
Removal of the Map Table Light
TASK 33-12-18-000-001-A
Removal of the Map Table Light Rheostats
TASK 33-12-18-000-802-A
Removal of the Map-Table Light Control-Box
TASK 46-26-22-000-001-A
Removal of the EFB Display Unit (DU)
TASK 46-26-22-000-002-A
Removal of the EFB Display Unit (DU) Mounting Bracket
TASK 56-12-11-000-803-C
Removal of the Structural Bracket Assembly
TASK 56-12-11-010-001-A
Opening of the Cockpit Sliding Windows
TASK 56-12-11-410-001-A
Closing of the Cockpit Sliding Windows
F Sliding Window lining
F Sliding Window Panel - Removal/Installation
3. Job Set-up
Subtask 56-12-11-941-078-A
A. Get Access
   (1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position at zone 210, in front of the sliding window.
Subtask 56-12-11-865-096-A
WARNING: MAKE SURE THAT THE CIRCUIT BREAKERS RELATED TO THE WEATHER RADAR ARE OPENED, SAFETIED AND TAGGED.
B. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C ALL
121VUCOM NAV/RADAR/15SQ1K13
** ON A/C NOT FOR ALL
121VUCOM NAV/RADAR/25SQ2K14
** ON A/C ALL
FOR FIN: 8DG1 (WINDOWSLIDING, L)
122VUANTI ICE/WINDOWS/L4DG1X14
122VUANTI ICE/WHC/15DG1X13
123VUANTI ICE/L/WHSLD1DG1AF10
FOR FIN: 8DG2 (WINDOWSLIDING, R)
122VUANTI ICE/WINDOWS/R4DG2W14
122VUANTI ICE/WHC/25DG2W13
123VUANTI ICE/R/WHSLD1DG2AF03
Subtask 56-12-11-020-089-A ** ON A/C NOT FOR ALL
C. Removal of the Component
   (1) Remove the reading lights, if installed (Ref. AMM TASK 33-12-12-000-001):
     (a) FOR [8DG1] (WINDOW-SLIDING, L)
  • 25LE.
     (b) FOR [8DG2] (WINDOW-SLIDING, R)
  • 26LE.
   (2) Remove the personal tablet support, if installed (Ref. AMM D/O 25-13-41-00).
   (3) Remove the Electronic Flight Bag (EFB) Display Unit (DU), if installed (Ref. AMM D/O 46-26-22-00).
   (4) Remove the EFB DU mounting-bracket, if installed (Ref. AMM D/O 46-26-22-00).
Subtask 56-12-11-020-089-B ** ON A/C NOT FOR ALL
C. Removal of the Component
   (1) Remove the map table lights (Ref. AMM TASK 33-12-12-000-002):
     (a) FOR [8DG1] (WINDOW-SLIDING, L)
  • 41LE.
     (b) FOR [8DG2] (WINDOW-SLIDING, R)
  • 42LE.
   (2) Remove the map-table light rheostats (Ref. AMM TASK 33-12-18-000-001):
     (a) FOR [8DG1] (WINDOW-SLIDING, L)
  • 39LE.
     (b) FOR [8DG2] (WINDOW-SLIDING, R)
  • 40LE.
   (3) Remove the personal tablet support, if installed (Ref. AMM D/O 25-13-41-00).
   (4) Remove the EFB DU, if installed (Ref. AMM TASK 46-26-22-000-001).
   (5) Remove the EFB DU mounting-bracket, if installed (Ref. AMM TASK 46-26-22-000-002).
Subtask 56-12-11-020-089-D ** ON A/C NOT FOR ALL
C. Removal of the Component
   (1) Remove the map table lights (Ref. AMM TASK 33-12-12-000-804):
     (a) FOR [8DG1] (WINDOW-SLIDING, L)
  • 41LE.
     (b) FOR [8DG2] (WINDOW-SLIDING, R)
  • 42LE.
   (2) Remove the map-table light rheostats (Ref. AMM TASK 33-12-18-000-802):
     (a) FOR [8DG1] (WINDOW-SLIDING, L)
  • 53LE.
     (b) FOR [8DG2] (WINDOW-SLIDING, R)
  • 54LE.
   (3) Remove the personal tablet support, if installed (Ref. AMM TASK 25-13-41-000-803).
   (4) Remove the EFB DU, if installed (Ref. AMM TASK 46-26-22-000-001).
   (5) Remove the EFB DU mounting-bracket, if installed (Ref. AMM TASK 46-26-22-000-002).
Subtask 56-12-11-020-090-A
D. Removal of the Sliding Window Lining
F Sliding Window lining
   (1) Open the sliding window 8DG1 (8DG2) (Ref. AMM TASK 56-12-11-010-001).
   (2) Remove the screw (5) and the pencil holder assembly (7).
   (3) Remove the screw (21) and the washer (20).
   (4) Remove the screw (19) and the washer (18).
   (5) Remove the handle (6).
   (6) Remove the screw (9) and the washer (8).
   (7) Remove the screw (15) and the washer (14).
   (8) Remove the guide (13).
   (9) Close the sliding window (Ref. AMM TASK 56-12-11-410-001).
   (10) Remove the blanking plug (4), the screw (3) and the washer (2).
   (11) Remove the screws (11) and (12).
   (12) Lift the plate (17).
   (13) Remove the sliding window lining (16).
   (14) Disconnect the electrical connector (10) from the receptacle.
   (15) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
   (16) Remove the structural bracket assembly, if installed (Ref. AMM TASK 56-12-11-000-803).
4. Procedure
Subtask 56-12-11-020-091-A
A. Removal of the Sliding Window Panel
F Sliding Window Panel - Removal/Installation
   (1) Loosen the screws (32).
     (a) For the screw that is behind the axix of the control panel, use the 98D56103002001 WRENCH, REMOVAL - SLIDING WINDOW OF SPS .
   (2) Use the CUP - SUCTION to hold and move the sliding window panel (30).
   (3) Hold the window panel (30) in position and remove the screws (32) and the washers (33).
   (4) Move the frame of the sliding window to the open position (the sliding window panel (30) stays in position in its housing).
   (5) Carefully remove the sliding window panel (30) and the retainer (31).
   (6) Remove the sealant from the retainer (31) with the Textile-Lint free Cotton - (Material No.14SBA1) soaked with Non Aqueous Cleaner-General - - (Material No.08BAA9) .
[Rev.10 from 2021] 2026.04.02 06:30:25 UTC
"WTRUIB" 2025