General Visual Inspection of Fuselage Skin around Cutout for Tail Compartment Access Door, between FR 70 and FR 73 and between STGR 25 RH and Bottom ...

TASK 53-51-00-210-019-A
General Visual Inspection of Fuselage Skin around Cutout for Tail Compartment Access Door, between FR 70 and FR 73 and between STGR 25 RH and Bottom ...

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

WARNING: YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU START WORK:

ON THE THS OR IN THE REAR FUSELAGE
ON TOP OF THE WINGS OR PYLONS.

WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.

ZONE: 300

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	1	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
300	STABILIZERS AND TAIL UNIT

D. Referenced Information

REFERENCE	DESIGNATION
SRM 53511101	(for corrective action)
SRM 53511102	(for corrective action)
Fuselage Skin around Cutout for Tail Compartment Access Door

3. Job Set-up
Subtask 53-51-00-941-066-A

A. Install the ground support equipment.
(1) Put a WARNING NOTICE(S) in position to tell persons not to operate the flight controls.
(2) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in the required position.

Subtask 53-51-00-110-066-A

B. Cleaning Procedure

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

(1) Clean the area with a lint-free cotton cloth Textile-Lint free Cotton - (Material No.14SBA1) and the Non Aqueous Cleaner-General - - (Material No.08BAA9) , and let the area dry.

4. Procedure
Subtask 53-51-00-210-071-A

A. Inspection
(1) Examine the following area for scratches, dents and cracks:

the fuselage skin around the cutout for the tail compartment access door between FR 70 and FR 73 and from stringer 25 RH to bottom centerline, external surface.

NOTE: If necessary, refer to the ASRM SRM 53511101 for the allowable damage limits.

NOTE: If necessary, refer to the ASRM SRM 53511102 for the correct repair procedure.

5. Close-up
Subtask 53-51-00-942-069-A

A. Remove the ground support equipment.
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the WARNING NOTICE(S).
(3) Remove the access platform(s).

[Rev.10 from 2021] 2026.04.02 06:29:27 UTC