General Visual Inspection of Fuselage Skin around Aft Passenger/Crew Door Cotouts between FR 65 and FR 70 and from Stringer 6 to Stringer 26, External...

TASK 53-41-00-210-814-A
General Visual Inspection of Fuselage Skin around Aft Passenger/Crew Door Cotouts between FR 65 and FR 70 and from Stringer 6 to Stringer 26, External...

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 100
ZONE: 200

1. Reason for the Job
Refer to the MPD TASK: 534131-01
GENERAL VISUAL INSPECTION OF FUSELAGE SKIN AROUND AFT PASSENGER/CREW DOOR CUTOUTS, BETWEEN FR 65 AND FR 70 AND FROM STRINGER 6 TO STRINGER 26, EXTERNAL SURFACE (EXCEPT AREA UNDER SCUFF PLATE), LH/RH

NOTE: The effectivity of this task is "ALL". To know if this task is applicable to your aircraft, refer to the MPD task applicability. The information on weight variant groups is given in the MPD and SRM introductions.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
No specific	1	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
100	LOWER HALF FUSELAGE INCLUDING RADOME
200	UPPER HALF FUSELAGE

D. Referenced Information

REFERENCE	DESIGNATION
SRM 511100
SRM 512200
SRM 512300
Fuselage Skin around Aft Passenger/Crew Door Cutouts

3. Job Set-up
Subtask 53-41-00-010-228-A

A. Get Access
(1) Put the WARNING NOTICE(S) in position to tell persons not to operate the flight controls.
(2) Put on and attach the safety harness:

WARNING: BEFORE YOU START WORK, YOU MUST PUT ON A SAFETY HARNESS AND ATTACH IT TO THE ACCESS PLATFORM. WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.

(a) Put on and attach a safety harness before you start work in the work area.
(3) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in the required position.

Subtask 53-41-00-110-097-A

B. Preparation of the Inspection Area
(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) .

4. Procedure
Subtask 53-41-00-210-116-A

A. General Visual Inspection
(1) Do a general visual inspection of the external surface of the fuselage skin around the aft passenger/crew door cutouts, between FR 65 and FR 70 and from stringer 6 to stringer 26, (without the area below the scuff plate), left and right sides, for damage or discontinuities.
(2) Make sure that there is no:
(a) Corrosion damage:
If you find corrosion, refer to the Structural Repair Manual ( SRM 512200) for the corrosion types, inspection, removal and subsequent corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
If you find this type of damage, refer to the Structural Repair Manual ( SRM 511100) for the damage types, classification and corrective action.
(c) Paint layer damage:
If you find this type of damage, refer to the Structural Repair Manual ( SRM 512300) for general data for paint layers.

5. Close-up
Subtask 53-41-00-410-222-A

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).
(3) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.02 06:29:17 UTC