General Visual Inspection of Fuselage External Surface, between FR47 and FR70, from STGR23, LH/RH to Bottom Centerline, except Area covered by Belly Fairing

TASK 53-41-00-210-810-A
General Visual Inspection of Fuselage External Surface, between FR47 and FR70, from STGR23, LH/RH to Bottom Centerline, except Area covered by Belly Fairing

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

WARNING: YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU START WORK:

ON THE THS OR IN THE REAR FUSELAGE
ON TOP OF THE WINGS OR PYLONS.

WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.

ZONE: 100

1. Reason for the Job
Refer to the MPD TASK: 534108-01
GENERAL VISUAL INSPECTION OF FUSELAGE EXTERNAL SURFACE, BETWEEN FR 47/51 (A319)/ FR 47 (A320) AND FR 70, FROM STRINGER 23, LH/RH TO BOTTOM CENTERLINE, EXCEPT AREA COVERED BY BELLY FAIRING

NOTE: The effectivity of this task is ALL. To know, if this task is applicable for your aircraft, refer to the MPD task applicability and the weight variant data given in the SRM introduction.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	1	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
100	LOWER HALF FUSELAGE INCLUDING RADOME

D. Referenced Information

REFERENCE	DESIGNATION
SRM 53411101	(for corrective action)
SRM 53411102	(for corrective action)
Fuselage external Surface from STGR 23 RH/LH toBottom Centerline ** ON A/C NOT FOR ALL
Fuselage external Surface from STGR 23 RH/LH toBottom Centerline ** ON A/C NOT FOR ALL
Fuselage external Surface from STGR 23 RH/LH toBottom Centerline ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 53-41-00-941-068-A

A. Install the ground support equipment.
(1) Put a WARNING NOTICE(S) in position to tell persons not to operate the flight controls.
(2) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in the required position.

Subtask 53-41-00-110-093-A

B. Preparation of the Inspection Area
(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

(2) If necessary, clean the area with a lint-free cotton cloth Textile-Lint free Cotton - (Material No.14SBA1) and the Non Aqueous Cleaner-General - - (Material No.08BAA9) .
(3) Make sure that the inspection area is dry before you continue.

4. Procedure
Subtask 53-41-00-210-112-A

A. General Visual Inspection
(1) Do a general visual inspection of the fuselage external surface from stringer 23 LH/RH to bottom centerline, except the area covered by the belly fairing.
(a) For A320 and A321, do this between FR47 and FR70.

Look for scratches, dents and cracks.

(b) For A319, do this between FR47/51 and FR70.

Look for scratches, dents and cracks.

Look for scratches, dents and cracks.

(2) If necessary, refer to the ASRM SRM 53411101 for the allowable damage limits.
(3) If necessary, refer to the ASRM SRM 53411102 for the correct repair procedure.

5. Close-up
Subtask 53-41-00-942-090-A

A. Remove the ground support equipment.
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the WARNING NOTICE(S).
(3) Remove the access platform(s).

[Rev.10 from 2021] 2026.04.02 06:29:17 UTC