General Visual Inspection of AFT Cargo Door Cutout, Visible Part of Lateral Frames

TASK 53-41-00-210-803-A
General Visual Inspection of AFT Cargo Door Cutout, Visible Part of Lateral Frames

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 152

1. Reason for the Job
Refer to the MPD TASK: 534160-01
GENERAL VISUAL INSPECTION OF AFT CARGO DOOR CUTOUT, VISIBLE PART OF LATERAL FRAMES.

NOTE: The effectivity of this task is ALL. To know, if this task is applicable for your aircraft, refer to the MPD task applicability and the weight variant data given in the SRM introduction.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.05RDA1)	Adhesive Film Tape-Masking - -
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
152	AFT CARGO COMPARTMENT

D. Referenced Information

REFERENCE	DESIGNATION
TASK 51-78-00-916-001-A	Application of Temporary Protection System (TPS)
TASK 52-30-00-860-001-A	Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump
TASK 52-30-00-860-002-A	Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump
SRM 53411202	(for corrective action)
AFT Cargo Door Cutout - Lateral

3. Job Set-up
Subtask 53-41-00-010-137-A

A. Get Access
(1) Open the AFT cargo-compartment door (Ref. AMM TASK 52-30-00-860-001).
(2) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE adjacent to the AFT cargo-compartment door.

Subtask 53-41-00-110-088-A

B. Preparation of the Inspection Area
(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) .
(3) Remove the TPS layer, if it does not let you do a satisfactory inspection (Ref. AMM TASK 51-78-00-916-001).

4. Procedure
Subtask 53-41-00-210-105-A

A. General Visual Inspection
(1) Do a general visual inspection at the cutout of the AFT cargo door.
(a) For A320 and A321, do this for the visible part of the lateral FR52A and FR56. Look for:

corrosion
cracks
and any other damage.

(b) For A319, do this for the visible part of the lateral FR55A and FR59. Look for:

corrosion
cracks
and any other damage.

NOTE: If necessary, refer to the ASRM SRM 53411202 for the correct repair procedure.

Subtask 53-41-00-916-080-A

B. Application of Temporary Protection System

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

CAUTION: DO NOT APPLY TEMPORARY PROTECTION ON THE OXYGEN SYSTEMS. MAKE SURE THAT THE TEMPORARY PROTECTION DOES NOT GET:

ON COMPOSITE PARTS, CONTROL CABLES, PULLEYS,TEFLON BEARINGS.
ON LUBRICATED SURFACES.
IN DRAIN VALVES OR OTHER ORIFICES.

TEMPORARY PROTECTION ON OR IN THESE PARTS CAN CAUSE DAMAGE.

(1) Apply masking paper or masking tape Adhesive Film Tape-Masking - - (Material No.05RDA1) on the equipment and fittings adjacent to the area.
(2) If there is a TPS layer, do a check of the condition and integrity of the TPS layer (Ref. AMM TASK 51-78-00-916-001).

NOTE: Airbus recommends that you always apply a new layer of TPS. This is to make sure that the TPS layer continues to give satisfactory corrosion protection. Make sure that the TPS layer is in the correct condition after the check. If the TPS is in the correct condition, apply a new layer as a spray on the remaining layer.

(3) Replace the damaged TPS layer with a new layer of TPS on the inspection area, as recommended in the MPD (Ref. AMM TASK 51-78-00-916-001).
(4) If you used solvents, high-pressure water, steam and/or cleaning agents to clean the TPS layer:
(a) Apply a full new layer of TPS on the inspection area, as recommended in the MPD (Ref. AMM TASK 51-78-00-916-001).
(b) If there is no TPS layer, apply a new layer of TPS on the inspection area, as recommended in the MPD (Ref. AMM TASK 51-78-00-916-001).
(5) Remove the masking paper or the masking tape.

5. Close-up
Subtask 53-41-00-410-135-A

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).
(3) Close the Aft cargo-compartment door (Ref. AMM TASK 52-30-00-860-002).
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.04.02 06:29:16 UTC