Detailed Inspection of Door Stop Fittings on FR 66 and FR 68, LH/RH

TASK 53-41-00-210-029-A
Detailed Inspection of Door Stop Fittings on FR 66 and FR 68, LH/RH

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 261
ZONE: 262

1. Reason for the Job
Refer to the MPD TASK: 534134-01
DETAILED INSPECTION OF DOOR STOP FITTINGS ON FRAME 66 AND FRAME 68, LH/RH.

NOTE: The effectivity of this task is ALL. To know, if this task is applicable to your aircraft, refer to the MPD task applicability and the weight variant data given in the SRM introduction.

2. Job Set-up Information
A. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
261	AFT CABIN UTILITY AREA
262	AFT CABIN UTILITY AREA

C. Referenced Information

REFERENCE	DESIGNATION
TASK 25-23-45-000-003-A	Removal of the Door Frame Linings from the Left Aft Passenger/Crew Door
TASK 25-23-45-000-004-A	Removal of the Door Frame Linings from the Right Aft Passenger/Crew Door
TASK 25-23-45-400-005-A	Installation of the Door Frame Linings on the Right Aft Passenger/Crew Door
TASK 25-23-45-400-008-A	Installation of the Door Frame Linings on the Left Aft Passenger/Crew Door
TASK 25-80-00-000-001-A	Removal of the Insulation Blankets
TASK 25-80-00-400-001-A	Installation of the Insulation Blankets
SRM 511100	(for corrective action)
SRM 512200	(for corrective action)
Door Stop Fittings

3. Job Set-up
Subtask 53-41-00-010-104-A

A. Get Access
(1) Remove the door frame linings (Ref. AMM TASK 25-23-45-000-003) and (Ref. AMM TASK 25-23-45-000-004).
(2) Remove the thermal and acoustical insulation blankets (Ref. AMM TASK 25-80-00-000-001).

NOTE: Identify the blankets for installation.

Subtask 53-41-00-110-180-A

B. Preparation of the Inspection Area
(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

(2) If not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) .

4. Procedure
Subtask 53-41-00-210-087-A

A. Inspection
(1) Do a detailed inspection of the door stop fittings on FR66 and FR68, LH/RH.
(2) Make sure that there is no:
(a) Corrosion damage:

If you find corrosion, refer to the SRM 512200 for the corrosion types, inspection, removal and subsequent corrosion protection.

(b) Other damage (cracks, scratches, stress, marks, bumps, and other)

If you find this type of damage, refer to the SRM 511100 for damage types, classification and corrective action.

5. Close-up
Subtask 53-41-00-410-103-A

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the thermal and acoustical insulation blankets (Ref. AMM TASK 25-80-00-400-001).
(3) Install the door frame linings (Ref. AMM TASK 25-23-45-400-008) and (Ref. AMM TASK 25-23-45-400-005).
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.04.02 06:29:15 UTC