DOC AIRBUS | AMM A320FDetailed Inspection of Skin in Circumferential Splice and Stringer Coupling Areas at FR64, from STGR10, LH/RH to Crown Center Line
TASK 53-41-00-210-020-A
Detailed Inspection of Skin in Circumferential Splice and Stringer Coupling Areas at FR64, from STGR10, LH/RH to Crown Center Line
Refer to the MPD TASK: 534113-01
DETAILED INSPECTION OF SKIN IN CIRCUMFERENTIAL SPLICE AND STRINGER COUPLING AREAS AT FR 64, FROM STRINGER 10, LH/RH TO CROWN CENTER LINE, EXTERNAL SURFACE
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Referenced Information
3. Job Set-up
Subtask 53-41-00-941-059-A
Subtask 53-41-00-210-076-A
Subtask 53-41-00-942-076-A
[Rev.10 from 2021]
2026.04.02 06:29:15 UTC
Detailed Inspection of Skin in Circumferential Splice and Stringer Coupling Areas at FR64, from STGR10, LH/RH to Crown Center Line
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
ZONE: 200
1. Reason for the JobRefer to the MPD TASK: 534113-01
DETAILED INSPECTION OF SKIN IN CIRCUMFERENTIAL SPLICE AND STRINGER COUPLING AREAS AT FR 64, FROM STRINGER 10, LH/RH TO CROWN CENTER LINE, EXTERNAL SURFACE
NOTE: The effectivity of this task is ALL. To know, if this task is applicable for your aircraft, refer to the MPD task applicability and the weight variant data given in the SRM introduction.
2. Job Set-up InformationA. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 6M (20 FT) |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.08BAA9) | Non Aqueous Cleaner-General - - |
| (Material No.14SBA1) | Textile-Lint free Cotton - |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 200 | UPPER HALF FUSELAGE |
| REFERENCE | DESIGNATION |
|---|---|
| SRM 53411101 | (for corrective action) |
Circumferential Skin Splice FR64Subtask 53-41-00-941-059-A
A. Get Access
(1) Put the ACCESS PLATFORM 6M (20 FT) in position adjacent to FR64.
Subtask 53-41-00-110-163-A (1) Put the ACCESS PLATFORM 6M (20 FT) in position adjacent to FR64.
B. Preparation of the Inspection Area
(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) .
(3) Make sure that the inspection areas are dry before you continue.
4. Procedure(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) .
(3) Make sure that the inspection areas are dry before you continue.
Subtask 53-41-00-210-076-A
A. Detailed Inspection
(1) Do a detailed inspection of skin in circumferential splice and stringer coupling areas at FR64. Do this from STGR10 LH/RH to crown center line. Look for:
5. Close-up(1) Do a detailed inspection of skin in circumferential splice and stringer coupling areas at FR64. Do this from STGR10 LH/RH to crown center line. Look for:
- Cracks.
NOTE: If necessary, refer to the ASRM SRM 53411101 for the correct repair procedure.
Subtask 53-41-00-942-076-A
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.