DOC AIRBUS | AMM A320FSpecial Detailed Inspection (LFEC) of Lower Skin of Longitudinal Lap Joints at Stringer 18, between FR 35 (A319/A320) and FR 47 (A320)/ FR 47/51 (A319) ...
TASK 53-31-00-220-812-A
Special Detailed Inspection (LFEC) of Lower Skin of Longitudinal Lap Joints at Stringer 18, between FR 35 (A319/A320) and FR 47 (A320)/ FR 47/51 (A319) ...
Refer to the MPD TASK: 533127-01
SPECIAL DETAILED INSPECTION (LFEC) OF LOWER SKIN OF LONGITUDINAL LAP JOINTS AT STRINGER 18, BETWEEN FR 35 (A319/A320) AND FR 47 (A320) / FR 47/51 (A319) / FR 47/54 (A318), EXTERNAL SURFACE, LH/RH.
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Referenced Information
3. Job Set-up
Subtask 53-31-00-010-140-A
Subtask 53-31-00-220-077-A ** ON A/C NOT FOR ALL
Subtask 53-31-00-410-137-A
[Rev.10 from 2021]
2026.04.02 06:29:08 UTC
Special Detailed Inspection (LFEC) of Lower Skin of Longitudinal Lap Joints at Stringer 18, between FR 35 (A319/A320) and FR 47 (A320)/ FR 47/51 (A319) ...
WARNING:
PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
- COMPONENTS THAT MOVE.
WARNING:
MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
WARNING:
YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU START WORK:
- ON THE THS OR IN THE REAR FUSELAGE
- ON TOP OF THE WINGS OR PYLONS.
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
CAUTION:
DO NOT APPLY TEMPORARY PROTECTION SYSTEM (TPS) ON THE INSPECTION AREA. IF YOU APPLY TPS ON THE INSPECTION AREA, YOU CAN CAUSE DAMAGE TO THE AIRCRAFT.
ZONE: 240
1. Reason for the JobRefer to the MPD TASK: 533127-01
SPECIAL DETAILED INSPECTION (LFEC) OF LOWER SKIN OF LONGITUDINAL LAP JOINTS AT STRINGER 18, BETWEEN FR 35 (A319/A320) AND FR 47 (A320) / FR 47/51 (A319) / FR 47/54 (A318), EXTERNAL SURFACE, LH/RH.
NOTE: The effectivity of this task is "ALL". To know if this task is applicable to youThe information on weight variant groups is given in the MPD and SRM introductio
2. Job Set-up InformationA. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.08BAA9) | Non Aqueous Cleaner-General - - |
| (Material No.14SBA1) | Textile-Lint free Cotton - |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 240 | MID PASSENGER COMPARTMENT |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 51-78-00-916-001-A | Application of Temporary Protection System (TPS) |
| SRM 511100 | |
| SRM 512200 | |
| SRM 512300 | |
| NTM 533127 | |
| SRM 512300 | (for corrective action) |
| SRM 512400 | (for corrective action) |
Subtask 53-31-00-010-140-A
A. Get Access
(1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position below the inspection area.
Subtask 53-31-00-110-143-A (1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position below the inspection area.
B. Preparation of the Inspection Area
(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) .
(3) Make sure that there is no TPS layer and if there is a TPS layer, remove it (Ref. AMM TASK 51-78-00-916-001).
(4) Remove the sealant and/or paint from the inspection area if this is necessary for the Non-destructive Testing Manual (NTM) task.
4. Procedure(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) .
(3) Make sure that there is no TPS layer and if there is a TPS layer, remove it (Ref. AMM TASK 51-78-00-916-001).
(4) Remove the sealant and/or paint from the inspection area if this is necessary for the Non-destructive Testing Manual (NTM) task.
Subtask 53-31-00-220-077-A ** ON A/C NOT FOR ALL
A. Inspection
Lower Skin of Longitudinal Lap Joints at Stringer 18, between FR 35 and FR 47, External Surface, LH/RH ** ON A/C NOT FOR ALL
(1) Do a special detailed inspection (LFEC) for damage and discontinuities on the left and the right sides of:
(a) Corrosion damage:
If you find corrosion, refer to the Structural Repair Manual ( SRM 512200) for the corrosion types, inspection, removal and subsequent corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
If you find this type of damage, refer to the Structural Repair Manual ( SRM 511100) for the damage types, classification and corrective action.
(c) Paint layer damage:
If you find this type of damage, refer to the Structural Repair Manual ( SRM 512300) for general data for paint layers.
Subtask 53-31-00-220-077-B ** ON A/C NOT FOR ALL Lower Skin of Longitudinal Lap Joints at Stringer 18, between FR 35 and FR 47, External Surface, LH/RH ** ON A/C NOT FOR ALL - The external surface of the lower skin of the longitudinal lap joints at stringer 18, between FR 35 and FR 47 ( NTM 533127).
(a) Corrosion damage:
If you find corrosion, refer to the Structural Repair Manual ( SRM 512200) for the corrosion types, inspection, removal and subsequent corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
If you find this type of damage, refer to the Structural Repair Manual ( SRM 511100) for the damage types, classification and corrective action.
(c) Paint layer damage:
If you find this type of damage, refer to the Structural Repair Manual ( SRM 512300) for general data for paint layers.
A. Inspection
Lower Skin of Longitudinal Lap Joints at Stringer 18, between FR 35.8 and FR 47, External Surface, LH/RH ** ON A/C NOT FOR ALL
(1) Do a special detailed inspection (LFEC) for damage and discontinuities on the left and the right sides of:
(a) Corrosion damage:
If you find corrosion, refer to the Structural Repair Manual ( SRM 512200) for the corrosion types, inspection, removal and subsequent corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
If you find this type of damage, refer to the Structural Repair Manual ( SRM 511100) for the damage types, classification and corrective action.
(c) Paint layer damage:
If you find this type of damage, refer to the Structural Repair Manual ( SRM 512300) for general data for paint layers.
Subtask 53-31-00-220-077-C ** ON A/C NOT FOR ALL Lower Skin of Longitudinal Lap Joints at Stringer 18, between FR 35.8 and FR 47, External Surface, LH/RH ** ON A/C NOT FOR ALL - The external surface of the lower skin of the longitudinal lap joints at stringer 18, between FR 35.8 and FR 47 ( NTM 533127).
(a) Corrosion damage:
If you find corrosion, refer to the Structural Repair Manual ( SRM 512200) for the corrosion types, inspection, removal and subsequent corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
If you find this type of damage, refer to the Structural Repair Manual ( SRM 511100) for the damage types, classification and corrective action.
(c) Paint layer damage:
If you find this type of damage, refer to the Structural Repair Manual ( SRM 512300) for general data for paint layers.
A. Inspection
Lower Skin of Longitudinal Lap Joints at Stringer 18, between FR 35 and FR 47/51, External Surface, LH/RH ** ON A/C NOT FOR ALL
(1) Do a special detailed inspection (LFEC) for damage and discontinuities on the left and the right sides of:
(a) Corrosion damage:
If you find corrosion, refer to the Structural Repair Manual ( SRM 512200) for the corrosion types, inspection, removal and subsequent corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
If you find this type of damage, refer to the Structural Repair Manual ( SRM 511100) for the damage types, classification and corrective action.
(c) Paint layer damage:
If you find this type of damage, refer to the Structural Repair Manual ( SRM 512300) for general data for paint layers.
Subtask 53-31-00-916-080-A Lower Skin of Longitudinal Lap Joints at Stringer 18, between FR 35 and FR 47/51, External Surface, LH/RH ** ON A/C NOT FOR ALL - The external surface of the lower skin of the longitudinal lap joints at stringer 18, between FR 35 and FR 47/51 ( NTM 533127).
(a) Corrosion damage:
If you find corrosion, refer to the Structural Repair Manual ( SRM 512200) for the corrosion types, inspection, removal and subsequent corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
If you find this type of damage, refer to the Structural Repair Manual ( SRM 511100) for the damage types, classification and corrective action.
(c) Paint layer damage:
If you find this type of damage, refer to the Structural Repair Manual ( SRM 512300) for general data for paint layers.
B. Sealant or Paint Application
(1) If the NTM procedure asked to remove the sealant and/or paint from the inspection area, apply sealant ( SRM 512400) or paint ( SRM 512300) on the inspection area.
5. Close-up(1) If the NTM procedure asked to remove the sealant and/or paint from the inspection area, apply sealant ( SRM 512400) or paint ( SRM 512300) on the inspection area.
Subtask 53-31-00-410-137-A
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.