General Visual Inspection of Forward Cargo Door Cutout, Visible Part of Lateral FR 24A and FR 28

TASK 53-21-00-210-002-A
General Visual Inspection of Forward Cargo Door Cutout, Visible Part of Lateral FR 24A and FR 28

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 132

1. Reason for the Job
Refer to the MPD TASK: 532135-01
GENERAL VISUAL INSPECTION OF FORWARD CARGO DOOR CUTOUT, VISIBLE PART OF LATERAL FR 24A AND FR 28

NOTE: The effectivity of this task is "ALL". To know if this task is applicable to your aircraft, refer to the MPD task applicability and the weight variant data given in the SRM introduction.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	AR	PAPER - MASKING

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.05RDA1)	Adhesive Film Tape-Masking - -
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.12ABB1)	Corrosion Preventive Compound-Water Displacing Hard Film -
(Material No.12ABC1)	Corrosion Preventive Compound_Water Displacing Soft Film -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
132	FORWARD CARGO COMPARTMENT
825

D. Referenced Information

REFERENCE	DESIGNATION
TASK 51-78-00-916-001-A	Application of Temporary Protection System (TPS)
TASK 52-30-00-860-001-A	Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump
TASK 52-30-00-860-002-A	Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump
SRM 511100	(for corrective action)
SRM 512200	(for corrective action)
Forward Cargo Door Cutout at FR24A and FR28

3. Job Set-up
Subtask 53-21-00-010-083-A

A. Get Access
(1) Put an ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position at the forward cargo-compartment door 825.
(2) Open the forward cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-001).

Subtask 53-21-00-110-087-A

B. Preparation of the Inspection Area
(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If it is not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) .
(3) If there is a Temporary Protection System (TPS) layer and if it does not let you do a satisfactory inspection, remove the TPS layer (Ref. AMM TASK 51-78-00-916-001).

4. Procedure
Subtask 53-21-00-210-072-A

A. Inspection

Forward Cargo Door Cutout at FR24A and FR28

(1) Do a general visual inspection of the cutout of the forward cargo-compartment door. This inspection is applicable to the lateral part of FR24A and FR28 that you can see.
(2) Make sure that there is no:
(a) Corrosion damage:
- If you find corrosion damage, refer to the Structural Repair Manual SRM 512200 for types of corrosion, inspection, removal and corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
- If you find other damage, refer to the Structural Repair Manual SRM 511100 for damage classification and corrective action.

Subtask 53-21-00-916-062-A

B. Application of the Temporary Protection System

Forward Cargo Door Cutout at FR24A and FR28

CAUTION: DO NOT APPLY TEMPORARY PROTECTION ON THE OXYGEN SYSTEMS. MAKE SURE THAT THE TEMPORARY PROTECTION DOES NOT GET:

ON COMPOSITE PARTS, CONTROL CABLES, PULLEYS,TEFLON BEARINGS.
ON LUBRICATED SURFACES.
IN DRAIN VALVES OR OTHER ORIFICES.

TEMPORARY PROTECTION ON OR IN THESE PARTS CAN CAUSE DAMAGE.

(1) If there is a TPS layer, do a check of the condition of the TPS layer (Ref. AMM TASK 51-78-00-916-001).

NOTE: Airbus recommends that you always apply a new layer of TPS. This is to make sure that the TPS layer continues to give satisfactory corrosion protection. If, after the check, you think that the TPS layer is in the correct condition, you can apply a new layer as a spray on the existing layer.

(2) Put PAPER - MASKING or Adhesive Film Tape-Masking - - (Material No.05RDA1) on the equipment and fittings adjacent to the area.
(3) If the TPS layer has local damage, remove the damaged TPS layer and apply a new layer of Corrosion Preventive Compound_Water Displacing Soft Film - (Material No.12ABC1) or Corrosion Preventive Compound-Water Displacing Hard Film - (Material No.12ABB1) on the inspection area (Ref. AMM TASK 51-78-00-916-001)>.
(4) If, before the inspection, there was:

Removal of the TPS layer or
Cleaning of the inspection area with high-pressure water, steam, solvents and/or cleaning agents

Apply a full new layer of Corrosion Preventive Compound_Water Displacing Soft Film - (Material No.12ABC1) or Corrosion Preventive Compound-Water Displacing Hard Film - (Material No.12ABB1) on the inspection area (Ref. AMM TASK 51-78-00-916-001).
(5) Remove the PAPER - MASKING or the Adhesive Film Tape-Masking - - (Material No.05RDA1) .

5. Close-up
Subtask 53-21-00-410-081-A

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the forward cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-002).
(3) Remove the access platform(s).

[Rev.10 from 2021] 2026.04.02 06:28:58 UTC