DOC AIRBUS | AMM A320FInstallation of the Chain Cable Guide
TASK 53-16-12-400-801-A
Installation of the Chain Cable Guide
Self explanatory
2. Job Set-up Information
A. Consumable Materials
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 53-16-12-865-051-A ** ON A/C NOT FOR ALL
Subtask 53-16-12-420-050-A ** ON A/C NOT FOR ALL
Subtask 53-16-12-942-050-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.02 06:28:54 UTC
Installation of the Chain Cable Guide
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Consumable Materials
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.04TMB2) | Varnish-- Electrical Bonding Structure |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 211 | COCKPIT |
| 212 | COCKPIT |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 56-12-11-400-002-A | Installation of the Sliding Window Panel |
| TASK 56-12-11-400-002-A-01 | Installation of the Sliding Window Panel |
| ESPM 2044100 | |
Chain Cable GuideSubtask 53-16-12-865-051-A ** ON A/C NOT FOR ALL
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| FOR FIN: 40TA1 (DUEFB) FOR FIN: 39TA1 (DOCKING STATIONEFB LAPTOP) | |||
| 122VU | EFB/CAPT | 41TA1 | U08 |
| FOR FIN: 40TA2 (DUEFB) FOR FIN: 39TA2 (DOCKING STATIONEFB LAPTOP) | |||
| 49VU | EFB/F/O | 41TA2 | H09 |
Subtask 53-16-12-420-050-A ** ON A/C NOT FOR ALL
A. Installation of the Chain Cable Guide
(2) Put the chain (3) in the correct position.
(4) Apply the Varnish-- Electrical Bonding Structure (Material No.04TMB2) on the screws (1).
(5) Remove the CAP-BLANKING from each electrical connector and receptacle.
(7) Connect the electrical connectors (8).
(8) Install the washers (10), the screws (11) and the nuts (9) on the electrical connectors (8).
(9) Install the heat-shrink sleeves (6) in the correct position on the cables (4).
(10) Install the cable ties (5).
(11) Install the sliding window lining (Ref. AMM TASK 56-12-11-400-002).
Subtask 53-16-12-865-052-A ** ON A/C NOT FOR ALL WARNING:
MAKE SURE THAT THE INSTALLATION AND ROUTING OF ALL ELECTRICAL CABLES AGREE WITH THE REQUIREMENTS OF THE ELECTRICAL STANDARD PRACTICES MANUAL.
(1) Install the cables (4) into the chain (3). (2) Put the chain (3) in the correct position.
NOTE: You must make sure that the cables (4) are attached in front of the support (8).
(3) Install the washers (2) and the screws (1) on the chain (3). (4) Apply the Varnish-- Electrical Bonding Structure (Material No.04TMB2) on the screws (1).
(5) Remove the CAP-BLANKING from each electrical connector and receptacle.
NOTE: Make sure that all the electrical connections are clean and in the correct condition.
(6) Connect the cables (4) to the electrical connectors (8) ESPM 2044100. (7) Connect the electrical connectors (8).
(8) Install the washers (10), the screws (11) and the nuts (9) on the electrical connectors (8).
(9) Install the heat-shrink sleeves (6) in the correct position on the cables (4).
(10) Install the cable ties (5).
(11) Install the sliding window lining (Ref. AMM TASK 56-12-11-400-002).
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
5. Close-up| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| FOR FIN: 40TA1 (DUEFB) FOR FIN: 39TA1 (DOCKING STATIONEFB LAPTOP) | |||
| 122VU | EFB/CAPT | 41TA1 | U08 |
| FOR FIN: 40TA2 (DUEFB) FOR FIN: 39TA2 (DOCKING STATIONEFB LAPTOP) | |||
| 49VU | EFB/F/O | 41TA2 | H09 |
Subtask 53-16-12-942-050-A ** ON A/C NOT FOR ALL
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(1) Make sure that the work area is clean and clear of tools and other items.