DOC AIRBUS | AMM A320FSpecial Detailed Inspection of Windshield Side Post at FR4, Upper Attachment, Internal Side, LH/RH
TASK 53-11-00-280-803-A
Special Detailed Inspection of Windshield Side Post at FR4, Upper Attachment, Internal Side, LH/RH
Refer to the MPD TASK: 531135-03
SPECIAL DETAILED INSPECTION (ROTO) OF WINDSHIELD SIDE POST AT FR 4, UPPER ATTACHMENT, INTERNAL SIDE, LH/RH.
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Referenced Information
3. Job Set-up
Subtask 53-11-00-010-152-A
Subtask 53-11-00-280-053-A
Subtask 53-11-00-410-150-A
[Rev.10 from 2021]
2026.04.02 06:28:41 UTC
Special Detailed Inspection of Windshield Side Post at FR4, Upper Attachment, Internal Side, LH/RH
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
ZONE: 210
1. Reason for the JobRefer to the MPD TASK: 531135-03
SPECIAL DETAILED INSPECTION (ROTO) OF WINDSHIELD SIDE POST AT FR 4, UPPER ATTACHMENT, INTERNAL SIDE, LH/RH.
NOTE: The effectivity of this task is "ALL". To know if this task is applicable to your aircraft, refer to the ALI task applicability.
2. Job Set-up InformationA. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | SCRAPER - NON METALLIC |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.08BAA9) | Non Aqueous Cleaner-General - - |
| (Material No.14SBA1) | Textile-Lint free Cotton - |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 210 | CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD |
| 211BC, 211KC, 211LC, 211NW, 212BC, 212KC, 212LC, 212NW |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 25-13-11-000-001-A | Removal of the Windshield Sunvisor |
| TASK 25-13-11-400-001-A | Installation of the Windshield Sunvisor |
| TASK 25-13-41-000-806-A | Removal of Outlet Assembly Panels 211LC and 212LC |
| TASK 25-13-41-400-805-A | Installation of Outlet Assembly Panels 211LC and 212LC |
| TASK 56-12-11-010-001-A | Opening of the Cockpit Sliding Windows |
| TASK 56-12-11-410-001-A | Closing of the Cockpit Sliding Windows |
| SRM 512300 | |
| SRM 512400 | |
| SRM 514200 | |
| NTM 531135 | |
| SRM 511100 | (for corrective action) |
| SRM 512200 | (for corrective action) |
| SRM 514200 | (for corrective action) |
Lining Panels of the Windshield Side Post at FR4Subtask 53-11-00-010-152-A
A. Get Access
(1) Open the sliding window (Ref. AMM TASK 56-12-11-010-001).
(2) Remove the windshield sunvisor (Ref. AMM TASK 25-13-11-000-001).
(3) Remove lining panels 211NW( 212NW), 211BC( 212BC) and 211KC( 212KC) to get access to the inspection area.
(4) Remove outlet assembly panel 211LC( 212LC) to get access to the inspection area (Ref. AMM TASK 25-13-41-000-806).
(5) If the supports (1) and (5) are installed, and if necessary, remove them as follows:
(a) Remove the bolts (2) and the support (1).
(b) Remove the nuts (3), the screws (4) and the support (5).
Subtask 53-11-00-110-168-A (1) Open the sliding window (Ref. AMM TASK 56-12-11-010-001).
(2) Remove the windshield sunvisor (Ref. AMM TASK 25-13-11-000-001).
(3) Remove lining panels 211NW( 212NW), 211BC( 212BC) and 211KC( 212KC) to get access to the inspection area.
(4) Remove outlet assembly panel 211LC( 212LC) to get access to the inspection area (Ref. AMM TASK 25-13-41-000-806).
(5) If the supports (1) and (5) are installed, and if necessary, remove them as follows:
(a) Remove the bolts (2) and the support (1).
(b) Remove the nuts (3), the screws (4) and the support (5).
B. Preparation of the Inspection Area
(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and the Textile-Lint free Cotton - (Material No.14SBA1) .
(3) If sealant or paint is applied on the inspection area:
4. Procedure(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and the Textile-Lint free Cotton - (Material No.14SBA1) .
(3) If sealant or paint is applied on the inspection area:
- Remove the sealant with the SCRAPER - NON METALLIC, and/or
- Remove the paint.
Subtask 53-11-00-280-053-A
A. Inspection
(1) Do a special detailed inspection of the internal side of the left and right upper attachments of the windshield side post at FR4. Do this for damage and discontinuities NTM 531135.
(2) Make a report of the damage after the NTM inspection:
(a) Corrosion:
If you find corrosion, refer to the Structural Repair Manual SRM 512200 for the corrosion types, inspection, removal and subsequent corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
If you find this type of damage, refer to the Structural Repair Manual SRM 511100 for damage types, classification and corrective action.
Subtask 53-11-00-420-089-A (1) Do a special detailed inspection of the internal side of the left and right upper attachments of the windshield side post at FR4. Do this for damage and discontinuities NTM 531135.
(2) Make a report of the damage after the NTM inspection:
(a) Corrosion:
If you find corrosion, refer to the Structural Repair Manual SRM 512200 for the corrosion types, inspection, removal and subsequent corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
If you find this type of damage, refer to the Structural Repair Manual SRM 511100 for damage types, classification and corrective action.
B. Installation of the Fasteners
(1) Refer to the installation drawing in the SRM identification section for the new fastener references.
(2) Install the fasteners in the examined holes SRM 514200.
Subtask 53-11-00-390-061-A (1) Refer to the installation drawing in the SRM identification section for the new fastener references.
(2) Install the fasteners in the examined holes SRM 514200.
C. Sealant or Paint Application
(1) If the NTM procedure told you to remove the sealant and/or paint from the inspection area, apply sealant SRM 512400 or paint SRM 512300 on the inspection area.
5. Close-up(1) If the NTM procedure told you to remove the sealant and/or paint from the inspection area, apply sealant SRM 512400 or paint SRM 512300 on the inspection area.
Subtask 53-11-00-410-150-A
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) If you removed the supports (1) and (5), install them again:
(a) Put the support (1) in position and install the bolts (2).
(b) Put the support (5) in position and install the screws (4) and the nuts (3).
(c) Tighten the nuts (3).
(3) Install outlet assembly panel 211LC( 212LC) (Ref. AMM TASK 25-13-41-400-805).
(4) Install lining panels 211BC( 212BC), 211KC( 212KC) and 211NW( 212NW).
(5) Install the windshield sunvisor (Ref. AMM TASK 25-13-11-400-001).
(6) Close the sliding window (Ref. AMM TASK 56-12-11-410-001).
(1) Make sure that the work area is clean and clear of tools and other items.
(2) If you removed the supports (1) and (5), install them again:
(a) Put the support (1) in position and install the bolts (2).
(b) Put the support (5) in position and install the screws (4) and the nuts (3).
(c) Tighten the nuts (3).
(3) Install outlet assembly panel 211LC( 212LC) (Ref. AMM TASK 25-13-41-400-805).
(4) Install lining panels 211BC( 212BC), 211KC( 212KC) and 211NW( 212NW).
(5) Install the windshield sunvisor (Ref. AMM TASK 25-13-11-400-001).
(6) Close the sliding window (Ref. AMM TASK 56-12-11-410-001).