Special Detailed Inspection of Windshield Side Post at FR4, Lower Corner

TASK 53-11-00-280-801-A
Special Detailed Inspection of Windshield Side Post at FR4, Lower Corner

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 210

1. Reason for the Job
Refer to the MPD TASK: 531134-02
SPECIAL DETAILED INSPECTION (HFEC) OF WINDSHIELD SIDE POST AT FR4, LOWER CORNER, RH.

NOTE: The effectivity of this task is "ALL". To know if this task is applicable to your aircraft, refer to the MPD task applicability.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	SCRAPER - NON METALLIC

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
210	CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD

D. Referenced Information

REFERENCE	DESIGNATION
TASK 56-12-11-010-001-A	Opening of the Cockpit Sliding Windows
TASK 56-12-11-410-001-A	Closing of the Cockpit Sliding Windows
NTM 531134
SRM 511100	(for corrective action)
SRM 512200	(for corrective action)
SRM 512300	(for corrective action)
SRM 512400	(for corrective action)
Windshield Side Post at FR4, Right Lower Corner

3. Job Set-up
Subtask 53-11-00-010-149-A

A. Get Access
(1) Open the cockpit sliding window ( (Ref. AMM TASK 56-12-11-010-001)).

Subtask 53-11-00-110-165-A

B. Preparation of the Inspection Area
(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If the inspection area is not sufficiently clean, clean it with Non Aqueous Cleaner-General - - (Material No.08BAA9) and the Textile-Lint free Cotton - (Material No.14SBA1) .
(3) If sealant or paint is applied on the inspection area:
- Remove the sealant with a SCRAPER - NON METALLIC.
- Remove the paint.

4. Procedure
Subtask 53-11-00-250-080-A

A. Inspection
(1) Do a special detailed inspection of the windshield side post at FR4, on the right lower corner of the windshield, for damage or discontinuities NTM 531134.
(2) Make a report of the damage after the NTM inspection:
(a) Corrosion:
If you find corrosion, refer to the Structural Repair Manual SRM 512200 for the corrosion types, inspection, removal and subsequent corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
If you find this type of damage, refer to the Structural Repair Manual SRM 511100 for the damage types, classification and corrective action.

Subtask 53-11-00-910-061-A

B. Sealant or Paint Application
(1) If the NTM procedure told you to remove the sealant and/or paint from the inspection area, apply sealant ( SRM 512400) or paint ( SRM 512300) on the inspection area.

5. Close-up
Subtask 53-11-00-410-145-A

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the cockpit sliding window ( (Ref. AMM TASK 56-12-11-410-001)).

[Rev.10 from 2021] 2026.04.02 06:28:41 UTC