General Visual Inspection of Fuselage Internal Structure and Floor Structure, including NLG Bay Panels, between FR 1 and FR 12, below Cockpit Floor Panels

TASK 53-11-00-210-806-A
General Visual Inspection of Fuselage Internal Structure and Floor Structure, including NLG Bay Panels, between FR 1 and FR 12, below Cockpit Floor Panels

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 121
ZONE: 122
ZONE: 125
ZONE: 126

1. Reason for the Job
Refer to the MPD TASK: 531192-01
GENERAL VISUAL INSPECTION OF FUSELAGE INTERNAL STRUCTURE AND FLOOR STRUCTURE, INCLUDING NLG BAY PANELS, BETWEEN FR 1 AND FR 12, BELOW COCKPIT FLOOR PANELS

NOTE: TPS can be only on the fuselage internal structure between FR 1 and FR 12 and the Aft face of the pressure bulkhead, from stringer 32, Left/Right side to the bottom centerline.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	AR	PAPER - MASKING

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.05RDA1)	Adhesive Film Tape-Masking - -
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.12ABB1)	Corrosion Preventive Compound-Water Displacing Hard Film -
(Material No.12ABC1)	Corrosion Preventive Compound_Water Displacing Soft Film -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
121	AVIONICS COMPARTMENT
122	AVIONICS COMPARTMENT
125	LATERAL AVIONIC COMPARTMENT
126	LATERAL AVIONIC COMPARTMENT
121AF, 121BF, 121CF, 122BF, 811, 812, 822

D. Referenced Information

REFERENCE	DESIGNATION
TASK 25-80-00-000-001-A	Removal of the Insulation Blankets
TASK 25-80-00-400-001-A	Installation of the Insulation Blankets
TASK 51-78-00-916-001-A	Application of Temporary Protection System (TPS)
TASK 52-41-00-010-002-A	Open the Avionics Compartment Doors for Access
TASK 52-41-00-410-002-A	Close the Avionics Compartment Doors after Access
TASK 53-12-13-000-001-A	Removal of the avionics compartment floor panels
TASK 53-12-13-400-001-A	Installation of the avionics compartment floor panels
SRM 51110001	(for corrective action)
SRM 51220001	(for corrective action)
Fuselage Internal Structure between FR1 and FR12

3. Job Set-up
Subtask 53-11-00-010-097-A

A. Get Access
(1) Put an ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE at zone 120.
(2) Open the avionics-compartment doors 811 812 822 (Ref. AMM TASK 52-41-00-010-002).
(3) Remove the floor panels (Ref. AMM TASK 53-12-13-000-001):
121AF 121BF 121CF 122BF.
(4) Remove the insulation blankets (Ref. AMM TASK 25-80-00-000-001).
(5) Remove the air conditioning ducts, as necessary.

Subtask 53-11-00-110-112-A

B. Preparation of the Inspection Area
(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If it is not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) .
(3) If there is a Temporary Protection System (TPS) layer and if it does not let you do a satisfactory inspection, remove the TPS layer (Ref. AMM TASK 51-78-00-916-001).

4. Procedure
Subtask 53-11-00-210-086-A

A. Inspection

Fuselage Internal Structure between FR1 and FR12

(1) Do a general visual inspection of the fuselage internal structure and floor structure. This inspection includes the NLG well panels and is applicable between FR1 and FR12, below the cockpit floor panels.
(2) Make sure that there is no:
(a) Corrosion damage:
- If you find corrosion damage, refer to the Structural Repair Manual SRM 51220001 for types of corrosion, inspection, removal and corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
- If you find other damage, refer to the Structural Repair Manual SRM 51110001 for damage classification and corrective action.
(3) Make sure that all the installations are attached correctly.

Subtask 53-11-00-916-069-A

B. Application of the Temporary Protection System

CAUTION: DO NOT APPLY TEMPORARY PROTECTION ON THE OXYGEN SYSTEMS. MAKE SURE THAT THE TEMPORARY PROTECTION DOES NOT GET:

ON COMPOSITE PARTS, CONTROL CABLES, PULLEYS,TEFLON BEARINGS.
ON LUBRICATED SURFACES.
IN DRAIN VALVES OR OTHER ORIFICES.

TEMPORARY PROTECTION ON OR IN THESE PARTS CAN CAUSE DAMAGE.

(1) If there is a TPS layer, do a check of the condition of the TPS layer (Ref. AMM TASK 51-78-00-916-001).

NOTE: Airbus recommends that you always apply a new layer of TPS. This is to make sure that the TPS layer continues to give satisfactory corrosion protection. If, after the check, you think that the TPS layer is in the correct condition, you can apply a new layer as a spray on the existing layer.

(2) Apply PAPER - MASKING or Adhesive Film Tape-Masking - - (Material No.05RDA1) on the equipment and fittings adjacent to the area.
(3) If the TPS layer has local damage, remove the damaged TPS layer and apply a new layer of Corrosion Preventive Compound_Water Displacing Soft Film - (Material No.12ABC1) or Corrosion Preventive Compound-Water Displacing Hard Film - (Material No.12ABB1) on the inspection area (Ref. AMM TASK 51-78-00-916-001).
(4) If, before the inspection, there was:

Removal of the TPS layer or
Cleaning of the inspection area with high-pressure water, steam, solvents and/or cleaning agents

Apply a full new layer of Corrosion Preventive Compound_Water Displacing Soft Film - (Material No.12ABC1) or Corrosion Preventive Compound-Water Displacing Hard Film - (Material No.12ABB1) on the inspection area (Ref. AMM TASK 51-78-00-916-001).
(5) Remove the PAPER - MASKING or the Adhesive Film Tape-Masking - - (Material No.05RDA1) .

5. Close-up
Subtask 53-11-00-410-097-A

A. Close Access
(1) Install the air conditioning ducts.
(2) Install the insulation blankets (Ref. AMM TASK 25-80-00-400-001).
(3) Install the floor panels (Ref. AMM TASK 53-12-13-400-001):
121AF 121BF 121CF 122BF.
(4) Make sure that the work area is clean and clear of tools and other items.
(5) Close the avionics-compartment door 811 812 822 (Ref. AMM TASK 52-41-00-410-002) .
(6) Remove the access platform(s).

[Rev.10 from 2021] 2026.04.02 06:28:44 UTC