DOC AIRBUS | AMM A320FDetailed Inspection of Cockpit Windshield, Lower Front Fitting at FR 4, Lower Attachment, External Surface, LH/RH
TASK 53-11-00-210-038-A
Detailed Inspection of Cockpit Windshield, Lower Front Fitting at FR 4, Lower Attachment, External Surface, LH/RH
Refer to the MPD TASK: 531170-01
DETAILED INSPECTION OF COCKPIT WINDSHIELD, LOWER FRONT FITTING AT FR 4, LOWER ATTACHMENT, EXTERNAL SURFACE, LH/RH
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Referenced Information
3. Job Set-up
Subtask 53-11-00-020-053-A
Subtask 53-11-00-220-053-A
(2) If you did not remove the TPS at the ”Preparation of the Inspection Area” paragraph, do a check of the condition and integrity of the TPS layer ( (Ref. AMM TASK 51-78-00-916-001)) and make the decision to apply a new TPS layer or not.
(3) If the TPS layer has local damage, remove the damaged TPS layer and apply a new layer of TPS ( (Ref. AMM TASK 51-78-00-916-001)).
5. Close-up
Subtask 53-11-00-420-088-A
[Rev.10 from 2021]
2026.04.02 06:28:43 UTC
Detailed Inspection of Cockpit Windshield, Lower Front Fitting at FR 4, Lower Attachment, External Surface, LH/RH
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
ZONE: 210
1. Reason for the JobRefer to the MPD TASK: 531170-01
DETAILED INSPECTION OF COCKPIT WINDSHIELD, LOWER FRONT FITTING AT FR 4, LOWER ATTACHMENT, EXTERNAL SURFACE, LH/RH
NOTE: The effectivity of this task is "ALL". To know if this task is applicable to your aircraft, refer to the MPD task applicability.
2. Job Set-up InformationA. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.08BAA9) | Non Aqueous Cleaner-General - - |
| (Material No.14SBA1) | Textile-Lint free Cotton - |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 210 | CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 51-78-00-916-001-A | Application of Temporary Protection System (TPS) |
| TASK 56-11-11-000-001-A | Removal of the Windshield |
| TASK 56-11-11-000-001-A-01 | Removal of the Windshield |
| TASK 56-11-11-400-001-A | Installation of the Windshield |
| TASK 56-11-11-400-001-A-01 | Installation of the Windshield |
| SRM 511100 | (for corrective action) |
| SRM 512200 | (for corrective action) |
| SRM 512300 | (for corrective action) |
Cockpit Windshield - Lower Front Fittings at FR4Subtask 53-11-00-020-053-A
A. Get Access
(1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position at zone 210, in front of the windshield.
(2) Remove the lower retainers (Ref. AMM TASK 56-11-11-000-001).
Subtask 53-11-00-110-086-A (1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position at zone 210, in front of the windshield.
(2) Remove the lower retainers (Ref. AMM TASK 56-11-11-000-001).
B. Preparation of the Inspection Area
(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and the Textile-Lint free Cotton - (Material No.14SBA1) .
(3) If there is a temporary protection system (TPS) layer and if it does not let you do a satisfactory inspection, remove the TPS layer (Ref. AMM TASK 51-78-00-916-001).
4. Procedure(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and the Textile-Lint free Cotton - (Material No.14SBA1) .
(3) If there is a temporary protection system (TPS) layer and if it does not let you do a satisfactory inspection, remove the TPS layer (Ref. AMM TASK 51-78-00-916-001).
Subtask 53-11-00-220-053-A
A. Inspection
(1) Do a detailed inspection of the lower front fittings of the cockpit windshield for damage or discontinuities. This inspection is applicable to FR4, left and right sides.
(2) Make sure that there is no:
(a) Corrosion:
If you find corrosion, refer to the Structural Repair Manual SRM 512200 for the corrosion types, inspection, removal and subsequent corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
If you find this type of damage, refer to the Structural Repair Manual SRM 511100 for the damage types, classification and corrective action.
(c) Paint layer damage:
If you find this type of damage, refer to the Structural Repair Manual SRM 512300 for general data for paint layers.
Subtask 53-11-00-916-089-A (1) Do a detailed inspection of the lower front fittings of the cockpit windshield for damage or discontinuities. This inspection is applicable to FR4, left and right sides.
(2) Make sure that there is no:
(a) Corrosion:
If you find corrosion, refer to the Structural Repair Manual SRM 512200 for the corrosion types, inspection, removal and subsequent corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
If you find this type of damage, refer to the Structural Repair Manual SRM 511100 for the damage types, classification and corrective action.
(c) Paint layer damage:
If you find this type of damage, refer to the Structural Repair Manual SRM 512300 for general data for paint layers.
CAUTION:
DO NOT APPLY TEMPORARY PROTECTION SYSTEM (TPS) TYPE 3 ON THE MOVABLE COMPONENTS. USE ONLY TPS TYPE 1 GRADE 2. IF YOU DO NOT OBEY THIS INSTRUCTION, THE MECHANISMS WILL NOT OPERATE CORRECTLY.
B. Check and Application of the TPS LayerNOTE: There is no special requirement about the TPS layer application in this area. The operator can apply TPS or let the surface stay without protection.
(1) If you removed the TPS at the ”Preparation of the Inspection Area” paragraph, and you make the decision to apply a TPS layer, ( (Ref. AMM TASK 51-78-00-916-001)).(2) If you did not remove the TPS at the ”Preparation of the Inspection Area” paragraph, do a check of the condition and integrity of the TPS layer ( (Ref. AMM TASK 51-78-00-916-001)) and make the decision to apply a new TPS layer or not.
(3) If the TPS layer has local damage, remove the damaged TPS layer and apply a new layer of TPS ( (Ref. AMM TASK 51-78-00-916-001)).
Subtask 53-11-00-420-088-A
A. Close Access
(1) Install the lower retainers (Ref. AMM TASK 56-11-11-400-001).
(2) Make sure that the work area is clean and clear of tools and other items.
(3) Remove all the fixtures, tools, test and support equipment used during this procedure.
(4) Remove the access platform(s).
(1) Install the lower retainers (Ref. AMM TASK 56-11-11-400-001).
(2) Make sure that the work area is clean and clear of tools and other items.
(3) Remove all the fixtures, tools, test and support equipment used during this procedure.
(4) Remove the access platform(s).