DOC AIRBUS | AMM A320FVisual Check of the Emergency Exit Closure and the Slide Arming
TASK 52-70-00-040-010-A
Visual Check of the Emergency Exit Closure and the Slide Arming
MMEL 52-07-03A
CABIN OVERWING EXIT PERMANENTLY INDICATED OPEN ON THE DOOR/OXY SD PAGE
MMEL 52-07-03B
CABIN OVERWING EXIT PERMANENTLY INDICATED OPEN ON THE DOOR/OXY SD PAGE
MMEL 52-07-03C
CABIN OVERWING EXIT PERMANENTLY INDICATED OPEN ON THE DOOR/OXY SD PAGE
MMEL 52-07-03D
CABIN OVERWING EXIT PERMANENTLY INDICATED OPEN ON THE DOOR/OXY SD PAGE
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 52-70-00-010-064-A ** ON A/C NOT FOR ALL
Subtask 52-70-00-210-069-A ** ON A/C NOT FOR ALL
Subtask 52-70-00-410-064-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.02 06:28:27 UTC
Visual Check of the Emergency Exit Closure and the Slide Arming
Task Summary
1. Reason for the Job| Access | Test | Specific Tools | Mhr | E/T | Nb Men |
|---|---|---|---|---|---|
| YES | YES | NO | 0.3 | 0.3 | 1 |
MMEL 52-07-03A
CABIN OVERWING EXIT PERMANENTLY INDICATED OPEN ON THE DOOR/OXY SD PAGE
MMEL 52-07-03B
CABIN OVERWING EXIT PERMANENTLY INDICATED OPEN ON THE DOOR/OXY SD PAGE
MMEL 52-07-03C
CABIN OVERWING EXIT PERMANENTLY INDICATED OPEN ON THE DOOR/OXY SD PAGE
MMEL 52-07-03D
CABIN OVERWING EXIT PERMANENTLY INDICATED OPEN ON THE DOOR/OXY SD PAGE
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | WRENCH - HEXAGONAL |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 831, 841 |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 31-60-00-860-001-A | EIS Start Procedure |
| TASK 31-60-00-860-002-A | EIS Stop Procedure |
| TASK 52-10-00-010-001-A | Opening of the Passenger/Crew Door |
| TASK 52-10-00-410-001-A | Closing of the Passenger/Crew Door |
| TASK 52-21-11-000-001-A | Removal of the Emergency Exit Hatch |
| TASK 52-21-11-400-001-A | Installation of the Emergency Exit Hatch |
| TASK 52-22-00-010-802-A | Opening of the Overwing Emergency-Exit Door from the Passenger Compartment |
EMERGENCY EXIT ClosureSubtask 52-70-00-010-064-A ** ON A/C NOT FOR ALL
A. Get Access
(1) Put the access platform in position at the applicable FWD passenger/crew door 831 or 841.
(2) Open the applicable passenger/crew door (Ref. AMM TASK 52-10-00-010-001).
(3) Do an EIS start procedure (Ref. AMM TASK 31-60-00-860-001).
Subtask 52-70-00-010-064-C ** ON A/C NOT FOR ALL (1) Put the access platform in position at the applicable FWD passenger/crew door 831 or 841.
(2) Open the applicable passenger/crew door (Ref. AMM TASK 52-10-00-010-001).
(3) Do an EIS start procedure (Ref. AMM TASK 31-60-00-860-001).
A. Aircraft Maintenance Configuration
(1) Do the EIS start procedure (upper ECAM DU and lower ECAM DU only)
(Ref. AMM TASK 31-60-00-860-001).
4. Procedure(1) Do the EIS start procedure (upper ECAM DU and lower ECAM DU only)
(Ref. AMM TASK 31-60-00-860-001).
Subtask 52-70-00-210-069-A ** ON A/C NOT FOR ALL
A. Visual Check to Make Sure that the Emergency Exit is Correctly Closed and SLIDE ARMED
(1) Visual check to make sure that the applicable emergency exit hatch is correctly closed.
(a) Pull down the cover flap (3) from the hatch (4) and remove it.
(b) Examine the locking hooks (6) to make sure that they are engaged with the upper roller fittings (5) in the hatch frame.
(c) Install the cover flap (3) on the hatch (4) and push it against the hatch (4).
(d) On the ECAM control panel, push the DOOR key:
(2) Visual check to make sure that the applicable emergency exit hatch is in the ARMED mode
(a) Make sure that the escape-slide release mechanism is not in the MAINTENANCE mode.
1 Pull down the cover flap (3) from the hatch (4) and remove it.
2 Make sure that the latch pin (1) is not in the DISARMED position (latch pin retracted).
(b) If the latch pin (1) is in the DISARMED position (escape-slide release mechanism in MAINTENANCE mode), arm the slide release mechanism as follows:
1 With a WRENCH - HEXAGONAL, push the latch pin (1) against the spring (2).
2 Turn the head of the latch pin (1) a quarter turn clockwise to extend the latch pin (1).
3 Make sure that the white SLIDE ARMED indicator light, located in the cabin lining near the emergency exits, is on.
(c) Install the cover flap (3) on the hatch (4) and push it against the hatch (4).
(3) Entry in the log book
(a) If the indication is not correct, make an entry in the aircraft log book to record that:
Subtask 52-70-00-210-069-C ** ON A/C NOT FOR ALL (1) Visual check to make sure that the applicable emergency exit hatch is correctly closed.
(a) Pull down the cover flap (3) from the hatch (4) and remove it.
(b) Examine the locking hooks (6) to make sure that they are engaged with the upper roller fittings (5) in the hatch frame.
(c) Install the cover flap (3) on the hatch (4) and push it against the hatch (4).
(d) On the ECAM control panel, push the DOOR key:
- On the lower ECAM DU, the DOOR/OXY page comes into view.
NOTE: The hatch (4) must be flush with the fuselage.
(f) If the hatch position is not correct, remove the hatch (4) (Ref. AMM TASK 52-21-11-000-001) and install it again (Ref. AMM TASK 52-21-11-400-001). (2) Visual check to make sure that the applicable emergency exit hatch is in the ARMED mode
(a) Make sure that the escape-slide release mechanism is not in the MAINTENANCE mode.
1 Pull down the cover flap (3) from the hatch (4) and remove it.
2 Make sure that the latch pin (1) is not in the DISARMED position (latch pin retracted).
(b) If the latch pin (1) is in the DISARMED position (escape-slide release mechanism in MAINTENANCE mode), arm the slide release mechanism as follows:
1 With a WRENCH - HEXAGONAL, push the latch pin (1) against the spring (2).
2 Turn the head of the latch pin (1) a quarter turn clockwise to extend the latch pin (1).
3 Make sure that the white SLIDE ARMED indicator light, located in the cabin lining near the emergency exits, is on.
(c) Install the cover flap (3) on the hatch (4) and push it against the hatch (4).
NOTE: The white SLIDE ARMED indicator light goes off.
(d) If the latch pin (1) is in the extended position, make sure that the indication is correct on the lower ECAM DU. (3) Entry in the log book
(a) If the indication is not correct, make an entry in the aircraft log book to record that:
- The SLIDE indication of the hatch (4) is defective on the lower ECAM DU.
- The hatch is in the ARMED mode.
- The EMER EXIT indication is defective on the lower ECAM DU.
- The hatch (4) is correctly installed and locked.
A. Visual Check of the Emergency Exit Closure and the Slide Arming
(a) On the visual lock indicator (21):
1 Make sure that the black arrows (23) are aligned with the black lines (22) from the green segment.
(b) On the lower ECAM DU, on the DOOR/OXY page:
1 Push the DOOR key.
2 Make sure that the DOOR/OXY page comes into view.
3 If the "EMER EXIT" message stays on, examine the emergency overwing-door position from the outboard side.
1 Close the emergency overwing door (Ref. AMM TASK 52-22-00-010-802).
(2) Do a visual check to make sure that the applicable emergency overwing door is in the ARMED mode:
(a) Remove the handle cover (1).
(b) If the lever (3) is behind the disarm bracket (4), arm the slide release mechanism:
1 On the forward left emergency-overwing-door or the aft right emergency-overwing-door:
a Pull the slide release shaft (5) to the right side to release it from the disarm bracket (4).
b Turn the slide release shaft (5) counterclockwise and push it to the left side.
2 On the aft left emergency-overwing-door or the forward right emergency-overwing-door:
a Pull the slide release shaft (5) to the left side to release it from the disarm bracket (4).
b Turn the slide release shaft (5) clockwise and push it to the right side.
(c) Make sure that the SLIDE ARMED indicator light (2) comes on.
(d) Install the handle cover (1).
(e) The SLIDE ARMED indicator light (2) goes off.
(f) On the lower ECAM DU, on the DOOR/OXY page:
1 Push the DOOR key.
2 Make sure that the DOOR/OXY page comes into view.
3 Make sure that the message SLIDE in white color is shown for the applicable overwing doors.
(3) Make an entry in the logbook.
Subtask 52-70-00-210-071-A ** ON A/C NOT FOR ALL NOTE: This procedure is applicable only to MMEL 52-07-03A.
(1) Do a visual check to make sure that the applicable emergency overwing door is correctly closed: (a) On the visual lock indicator (21):
1 Make sure that the black arrows (23) are aligned with the black lines (22) from the green segment.
(b) On the lower ECAM DU, on the DOOR/OXY page:
1 Push the DOOR key.
2 Make sure that the DOOR/OXY page comes into view.
3 If the "EMER EXIT" message stays on, examine the emergency overwing-door position from the outboard side.
NOTE: The emergency overwing door must be flush with the fuselage.
(c) If the position of the emergency overwing door is not correct: 1 Close the emergency overwing door (Ref. AMM TASK 52-22-00-010-802).
(2) Do a visual check to make sure that the applicable emergency overwing door is in the ARMED mode:
(a) Remove the handle cover (1).
(b) If the lever (3) is behind the disarm bracket (4), arm the slide release mechanism:
1 On the forward left emergency-overwing-door or the aft right emergency-overwing-door:
a Pull the slide release shaft (5) to the right side to release it from the disarm bracket (4).
b Turn the slide release shaft (5) counterclockwise and push it to the left side.
2 On the aft left emergency-overwing-door or the forward right emergency-overwing-door:
a Pull the slide release shaft (5) to the left side to release it from the disarm bracket (4).
b Turn the slide release shaft (5) clockwise and push it to the right side.
(c) Make sure that the SLIDE ARMED indicator light (2) comes on.
(d) Install the handle cover (1).
(e) The SLIDE ARMED indicator light (2) goes off.
(f) On the lower ECAM DU, on the DOOR/OXY page:
1 Push the DOOR key.
2 Make sure that the DOOR/OXY page comes into view.
3 Make sure that the message SLIDE in white color is shown for the applicable overwing doors.
(3) Make an entry in the logbook.
B. Visual Check of the Emergency Exit Closure and the Slide Arming
(a) On the visual lock indicator (21):
1 Make sure that the black arrows (23) are aligned with the black lines (22) from the green segment.
(b) On the lower ECAM DU, on the DOOR/OXY page:
1 Push the DOOR key.
2 Make sure that the DOOR/OXY page comes into view.
3 If the "EMER EXIT" message stays on, examine the emergency overwing-door position from the outboard side.
1 Close the emergency overwing door (Ref. AMM TASK 52-22-00-010-802).
(2) Do a visual check to make sure that the applicable emergency overwing door is in the ARMED mode:
(a) Remove the handle cover (1).
(b) If the lever (3) is behind the disarm bracket (4), arm the slide release mechanism:
1 On the forward left emergency-overwing-door or the aft right emergency-overwing-door:
a Pull the slide release shaft (5) to the right side to release it from the disarm bracket (4).
b Turn the slide release shaft (5) counterclockwise and push it to the left side.
2 On the aft left emergency-overwing-door or the forward right emergency-overwing-door:
a Pull the slide release shaft (5) to the left side to release it from the disarm bracket (4).
b Turn the slide release shaft (5) clockwise and push it to the right side.
(c) Make sure that the SLIDE ARMED indicator light (2) comes on.
(d) Install the handle cover (1).
Subtask 52-70-00-210-072-A ** ON A/C NOT FOR ALL NOTE: This procedure is applicable only to MMEL 52-07-03B and MMEL 52-07-03C.
(1) Do a visual check to make sure that the applicable emergency overwing door is correctly closed: (a) On the visual lock indicator (21):
1 Make sure that the black arrows (23) are aligned with the black lines (22) from the green segment.
(b) On the lower ECAM DU, on the DOOR/OXY page:
1 Push the DOOR key.
2 Make sure that the DOOR/OXY page comes into view.
3 If the "EMER EXIT" message stays on, examine the emergency overwing-door position from the outboard side.
NOTE: The emergency overwing door must be flush with the fuselage.
(c) If the position of the emergency overwing door is not correct: 1 Close the emergency overwing door (Ref. AMM TASK 52-22-00-010-802).
(2) Do a visual check to make sure that the applicable emergency overwing door is in the ARMED mode:
(a) Remove the handle cover (1).
(b) If the lever (3) is behind the disarm bracket (4), arm the slide release mechanism:
1 On the forward left emergency-overwing-door or the aft right emergency-overwing-door:
a Pull the slide release shaft (5) to the right side to release it from the disarm bracket (4).
b Turn the slide release shaft (5) counterclockwise and push it to the left side.
2 On the aft left emergency-overwing-door or the forward right emergency-overwing-door:
a Pull the slide release shaft (5) to the left side to release it from the disarm bracket (4).
b Turn the slide release shaft (5) clockwise and push it to the right side.
(c) Make sure that the SLIDE ARMED indicator light (2) comes on.
(d) Install the handle cover (1).
NOTE: The SLIDE ARMED indicator light (2) can stay on after the installation of the handle cover (1).
(3) Make an entry in the logbook.C. Visual Check of the Emergency Exit Closure and the Slide Disarming
(a) On the visual lock indicator (21):
1 Make sure that the black arrows (23) are aligned with the black lines (22) from the green segment.
(b) On the lower ECAM DU, on the DOOR/OXY page:
1 Push the DOOR key.
2 Make sure that the DOOR/OXY page comes into view.
3 If the "EMER EXIT" message stays on, examine the emergency overwing-door position from the outboard side.
1 Close the emergency overwing door (Ref. AMM TASK 52-22-00-010-802).
(2) Do a visual check to make sure that the two emergency overwing doors on the same side are in the DISARMED mode:
(a) Remove the handle cover (1) of the two emergency overwing doors on the same side.
(b) Disarm the slide release mechanism of the two emergency overwing doors on the same side:
1 On the forward left emergency-overwing-door or the aft right emergency-overwing-door:
a Pull the slide release shaft (5) to the right side, turn it clockwise and engage it behind the disarm bracket (4).
2 On the aft left emergency-overwing-door or the forward right emergency-overwing-door:
a Pull the slide release shaft (5) to the left side, turn it counterclockwise and engage it behind the disarm bracket (4).
(c) Install the handle cover (1) of the two emergency overwing doors on the same side.
(3) Make an entry in the logbook.
5. Close-upNOTE: This procedure is applicable only to MMEL 52-07-03D.
(1) Do a visual check to make sure that the applicable emergency overwing door is correctly closed: (a) On the visual lock indicator (21):
1 Make sure that the black arrows (23) are aligned with the black lines (22) from the green segment.
(b) On the lower ECAM DU, on the DOOR/OXY page:
1 Push the DOOR key.
2 Make sure that the DOOR/OXY page comes into view.
3 If the "EMER EXIT" message stays on, examine the emergency overwing-door position from the outboard side.
NOTE: The emergency overwing door must be flush with the fuselage.
(c) If the position of the emergency overwing door is not correct: 1 Close the emergency overwing door (Ref. AMM TASK 52-22-00-010-802).
(2) Do a visual check to make sure that the two emergency overwing doors on the same side are in the DISARMED mode:
(a) Remove the handle cover (1) of the two emergency overwing doors on the same side.
(b) Disarm the slide release mechanism of the two emergency overwing doors on the same side:
1 On the forward left emergency-overwing-door or the aft right emergency-overwing-door:
a Pull the slide release shaft (5) to the right side, turn it clockwise and engage it behind the disarm bracket (4).
2 On the aft left emergency-overwing-door or the forward right emergency-overwing-door:
a Pull the slide release shaft (5) to the left side, turn it counterclockwise and engage it behind the disarm bracket (4).
(c) Install the handle cover (1) of the two emergency overwing doors on the same side.
NOTE: The SLIDE ARMED indicator light (2) can stay on after the installation of the handle cover (1).
(d) Put a PLACARD in position on the two disarmed emergency overwing doors on the same side to tell people not to use the two doors in an emergency situation. (3) Make an entry in the logbook.
Subtask 52-70-00-410-064-A ** ON A/C NOT FOR ALL
A. Close Access
(1) Remove all the ground support equipment, maintenance equipment, standard and special tools and all other items.
(2) Do an EIS stop procedure (Ref. AMM TASK 31-60-00-860-002).
(3) Close the applicable passenger/crew door 831 or 841 (Ref. AMM TASK 52-10-00-410-001) .
(4) Remove the access platform(s).
Subtask 52-70-00-410-064-C ** ON A/C NOT FOR ALL (1) Remove all the ground support equipment, maintenance equipment, standard and special tools and all other items.
(2) Do an EIS stop procedure (Ref. AMM TASK 31-60-00-860-002).
(3) Close the applicable passenger/crew door 831 or 841 (Ref. AMM TASK 52-10-00-410-001) .
(4) Remove the access platform(s).
A. Aircraft Maintenance Configuration
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Do the EIS stop procedure
(Ref. AMM TASK 31-60-00-860-002).
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Do the EIS stop procedure
(Ref. AMM TASK 31-60-00-860-002).