DOC AIRBUS | AMM A320FInstallation of the Switch Mechanism
TASK 52-32-21-400-009-A
Installation of the Switch Mechanism
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Expendable Parts
E. Referenced Information
3. Job Set-up
Subtask 52-32-21-860-060-A
Subtask 52-32-21-910-057-A ** ON A/C NOT FOR ALL
Subtask 52-32-21-410-059-B ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.02 06:28:02 UTC
Installation of the Switch Mechanism
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 1M (3 FT)-ADJUSTABLE |
| 98D52308002000 | 1 | CURVED SHIM |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.03HBD9) | Synthetic Ester base Grease-General Purpose Low Temp - |
| (Material No.12ABC1) | Corrosion Preventive Compound_Water Displacing Soft Film - |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 826AR | |
| 826BR, 826CR |
| FIG.ITEM | DESIGNATION | IPC-CSN |
|---|---|---|
| 367 | COTTER PIN | AIPC 52-32-21-45-020 |
| 6 | COTTER PIN | AIPC 52-32-21-45-020 |
| 19 | COTTER PIN | AIPC 52-32-21-45-100 |
| 96 | COTTER PIN | AIPC 52-32-21-45-100 |
| 14 | COTTER PIN | AIPC 52-32-21-45-140 |
| 14 | COTTER PIN | AIPC 52-32-21-45-150 |
| 91 | COTTER PIN | AIPC 52-32-21-45-150 |
| 16 | TAB WASHERS | AIPC 52-32-21-45-200 |
| 371 | TAB WASHERS | AIPC 52-32-21-45-200 |
| 16 | LOCKING DEVICE | AIPC 52-32-21-45-210 |
| 367 | COTTER PIN | AIPC 52-32-21-46-020 |
| 96 | COTTER PIN | AIPC 52-32-21-46-100 |
| 91 | COTTER PIN | AIPC 52-32-21-46-160 |
| 371 | TAB WASHERS | AIPC 52-32-21-46-210 |
| 6 | COTTER PIN | AIPC 52-32-84-42-020 |
| 19 | COTTER PIN | AIPC 52-32-84-42-100 |
| 14 | COTTER PIN | AIPC 52-32-84-42-150 |
| 16 | TAB WASHERS | AIPC 52-32-84-42-200 |
| 14 | COTTER PIN | AIPC 52-32-84-42-360 |
| 16 | LOCKING DEVICE | AIPC 52-32-84-42-430 |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 52-30-00-860-002-A | Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
| TASK 52-31-14-000-801-A | Removal of the FWD Cargo-Compartment Door Access-Panel |
| TASK 52-31-14-400-801-A | Installation of the FWD Cargo-Compartment Door Access-Panel |
| TASK 52-32-33-400-001-A | Installation of the Door Fairings and Access Panels |
| TASK 52-71-00-820-003-A | Adjustment of the Proximity Switches of the Cargo-Compartment Door Threshold |
Switch MechanismSubtask 52-32-21-860-060-A
A. Aircraft Maintenance Configuration
(1) Make sure that the ACCESS PLATFORM 1M (3 FT)-ADJUSTABLE is in position below the closed AFT cargo compartment door (referred to as cargo door).
(2) Make sure that the locking handle is moved away from the recess of the handle flap but not in the UNLOCKED position.
(3) Make sure that access panel 826AR is removed from the cargo door (Ref. AMM TASK 52-31-14-000-801).
4. Procedure(1) Make sure that the ACCESS PLATFORM 1M (3 FT)-ADJUSTABLE is in position below the closed AFT cargo compartment door (referred to as cargo door).
(2) Make sure that the locking handle is moved away from the recess of the handle flap but not in the UNLOCKED position.
(3) Make sure that access panel 826AR is removed from the cargo door (Ref. AMM TASK 52-31-14-000-801).
Subtask 52-32-21-910-057-A ** ON A/C NOT FOR ALL
A. Preparation for Installation
(1) Make sure that the parts retained from the removed component are clean and in the correct condition.
(2) Clean the component interfaces and the adjacent area.
(3) Do an inspection of the component interfaces and the adjacent area.
(4) Apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) to the bolt (23), the threaded pin of the shaft (18) and the mating surfaces of the support fitting (9).
Subtask 52-32-21-910-057-B ** ON A/C NOT FOR ALL (1) Make sure that the parts retained from the removed component are clean and in the correct condition.
(2) Clean the component interfaces and the adjacent area.
(3) Do an inspection of the component interfaces and the adjacent area.
(4) Apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) to the bolt (23), the threaded pin of the shaft (18) and the mating surfaces of the support fitting (9).
A. Preparation for Installation
(1) Make sure that the parts retained from the removed component are clean and in the correct condition.
(2) Clean the component interfaces and the adjacent area.
(3) Do an inspection of the component interfaces and the adjacent area.
(4) Apply the Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) to the bolts (10) and (23), and the mating surfaces of the support fitting (9) and the target lever (3).
Subtask 52-32-21-560-054-B ** ON A/C NOT FOR ALL (1) Make sure that the parts retained from the removed component are clean and in the correct condition.
(2) Clean the component interfaces and the adjacent area.
(3) Do an inspection of the component interfaces and the adjacent area.
(4) Apply the Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) to the bolts (10) and (23), and the mating surfaces of the support fitting (9) and the target lever (3).
B. Preparation of the Replacement Components
(1) Make sure that there are new tab washers (371) on the link assembly (88).
(2) If not, replace the tab washers (371) as follows:
(a) Release the tab washers (371) from the jam nuts (372).
(b) Remove the fork ends (95) and (99) from the connection rod (370).
(c) Remove and discard the tab washers (371) from the connection rod (370).
(d) Apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) on the threads of the connection rod (370).
(e) Install the new AIPC 52-32-21-45-200 TAB WASHERS (371) and the fork ends (95) and (99) on the connection rod (370).
(3) Make sure that the length between the fork ends (95) and (99) of the replacement link assembly (88) is as recorded in the removal procedure.
Subtask 52-32-21-420-065-B ** ON A/C NOT FOR ALL (1) Make sure that there are new tab washers (371) on the link assembly (88).
(2) If not, replace the tab washers (371) as follows:
(a) Release the tab washers (371) from the jam nuts (372).
(b) Remove the fork ends (95) and (99) from the connection rod (370).
(c) Remove and discard the tab washers (371) from the connection rod (370).
(d) Apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) on the threads of the connection rod (370).
(e) Install the new AIPC 52-32-21-45-200 TAB WASHERS (371) and the fork ends (95) and (99) on the connection rod (370).
(3) Make sure that the length between the fork ends (95) and (99) of the replacement link assembly (88) is as recorded in the removal procedure.
C. Installation of the Switch Mechanism
(1) Install the link assembly (88) as follows:
(a) Install the fork end (99) on the drive shaft lever (102) as follows:
1 If removed, install the sleeve (100) on the fork end (99).
2 Put the fork end (99) in position on the drive shaft lever (102).
3 Install the bolt (101), the washer (98) and the nut (97).
4 Tighten the nut (97) and safety it with the new AIPC 52-32-21-45-100 COTTER PIN (96).
(b) Install the fork end (95) on the target lever (90) as follows:
1 If removed, install the bush (94) on the fork end (95).
2 Put the fork end (95) on the target lever (90).
3 Install the bolt (89), the washer (93) and the nut (92).
4 Tighten the nut (92) and safety it with the new AIPC 52-32-21-45-150 COTTER PIN (91).
(2) Install the target lever (90) as follows:
(a) If removed, install the target (365) with the bolts (366), the washers (363) and the nuts (362) on the target lever (90).
(b) Install the target lever (90) as follows:
1 Put the target lever (90) on the support fitting (361) and install it with the washer (369) and the nut (368).
2 Tighten the nut (368) and safety it with the new AIPC 52-32-21-45-020 COTTER PIN (367).
(c) Install the fork end (95) on the target lever (90) (refer to the procedure (1) (b)).
Subtask 52-32-21-560-054-D ** ON A/C NOT FOR ALL (1) Install the link assembly (88) as follows:
(a) Install the fork end (99) on the drive shaft lever (102) as follows:
1 If removed, install the sleeve (100) on the fork end (99).
2 Put the fork end (99) in position on the drive shaft lever (102).
3 Install the bolt (101), the washer (98) and the nut (97).
4 Tighten the nut (97) and safety it with the new AIPC 52-32-21-45-100 COTTER PIN (96).
(b) Install the fork end (95) on the target lever (90) as follows:
1 If removed, install the bush (94) on the fork end (95).
2 Put the fork end (95) on the target lever (90).
3 Install the bolt (89), the washer (93) and the nut (92).
4 Tighten the nut (92) and safety it with the new AIPC 52-32-21-45-150 COTTER PIN (91).
(2) Install the target lever (90) as follows:
(a) If removed, install the target (365) with the bolts (366), the washers (363) and the nuts (362) on the target lever (90).
(b) Install the target lever (90) as follows:
1 Put the target lever (90) on the support fitting (361) and install it with the washer (369) and the nut (368).
2 Tighten the nut (368) and safety it with the new AIPC 52-32-21-45-020 COTTER PIN (367).
(c) Install the fork end (95) on the target lever (90) (refer to the procedure (1) (b)).
D. Preparation of the Replacement Components
(1) Make sure that there are new tab washers (371) on the link assembly (88).
(2) If not, replace the tab washers (371) as follows:
(a) Release the tab washers (371) from the jam nuts (372).
(b) Remove the fork ends (95) and (99) from the connection rod (370).
(c) Remove and discard the tab washers (371) from the connection rod (370).
(d) Apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) on the threads of the connection rod (370).
(e) Install the new AIPC 52-32-21-46-210 TAB WASHERS (371) and the fork ends (95) and (99) on the connection rod (370).
(3) Make sure that the length between the fork ends (95) and (99) of the replacement link assembly (88) is as recorded in the removal procedure.
Subtask 52-32-21-420-065-D ** ON A/C NOT FOR ALL (1) Make sure that there are new tab washers (371) on the link assembly (88).
(2) If not, replace the tab washers (371) as follows:
(a) Release the tab washers (371) from the jam nuts (372).
(b) Remove the fork ends (95) and (99) from the connection rod (370).
(c) Remove and discard the tab washers (371) from the connection rod (370).
(d) Apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) on the threads of the connection rod (370).
(e) Install the new AIPC 52-32-21-46-210 TAB WASHERS (371) and the fork ends (95) and (99) on the connection rod (370).
(3) Make sure that the length between the fork ends (95) and (99) of the replacement link assembly (88) is as recorded in the removal procedure.
E. Installation of the Switch Mechanism
(1) Install the link assembly (88) as follows:
(a) Install the fork end (99) on the drive shaft lever (102) as follows:
1 If removed, install the sleeve (100) on the fork end (99).
2 Put the fork end (99) in position on the drive shaft lever (102).
3 Install the bolt (101), the washer (98) and the nut (97).
4 Tighten the nut (97) and safety it with the new AIPC 52-32-21-46-100 COTTER PIN (96).
(b) Install the fork end (95) on the target lever (90) as follows:
1 If removed, install the bush (94) into the fork end (95).
2 Put the fork end (95) on the target lever (90).
3 Install the bolt (89), the washer (93) and the nut (92).
4 Tighten the nut (92) and safety it with the new AIPC 52-32-21-46-160 COTTER PIN (91).
(2) Install the target lever (90) as follows:
(a) If removed, install the target (365) with the bolts (366), the washers (363) and the nuts (362) on the target lever (90).
(b) Install the target lever (90) as follows:
1 Put the target lever (90) on the support fitting (361) and install it with the washer (369) and the nut (368).
2 Tighten the nut (368) and safety it with the new AIPC 52-32-21-46-020 COTTER PIN (367).
(c) Install the fork end (95) on the target lever (90) (refer to the procedure (1) (b)).
Subtask 52-32-21-560-054-E ** ON A/C NOT FOR ALL (1) Install the link assembly (88) as follows:
(a) Install the fork end (99) on the drive shaft lever (102) as follows:
1 If removed, install the sleeve (100) on the fork end (99).
2 Put the fork end (99) in position on the drive shaft lever (102).
3 Install the bolt (101), the washer (98) and the nut (97).
4 Tighten the nut (97) and safety it with the new AIPC 52-32-21-46-100 COTTER PIN (96).
(b) Install the fork end (95) on the target lever (90) as follows:
1 If removed, install the bush (94) into the fork end (95).
2 Put the fork end (95) on the target lever (90).
3 Install the bolt (89), the washer (93) and the nut (92).
4 Tighten the nut (92) and safety it with the new AIPC 52-32-21-46-160 COTTER PIN (91).
(2) Install the target lever (90) as follows:
(a) If removed, install the target (365) with the bolts (366), the washers (363) and the nuts (362) on the target lever (90).
(b) Install the target lever (90) as follows:
1 Put the target lever (90) on the support fitting (361) and install it with the washer (369) and the nut (368).
2 Tighten the nut (368) and safety it with the new AIPC 52-32-21-46-020 COTTER PIN (367).
(c) Install the fork end (95) on the target lever (90) (refer to the procedure (1) (b)).
F. Preparation of the Replacement Component
(1) Make sure that there are new tab washers (16) on the link assy (26).
(2) If not, replace the tab washers (16) as follows:
(a) Release the tab washers (16) from the jam nuts (17).
(b) Remove the fork ends (15) and (25) from the connection rod (18).
(c) Remove and discard the tab washers (16) from the connection rod (18).
(d) Apply the Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) to the threaded ends of the connection rod (18).
(e) Install the new AIPC 52-32-21-45-200 TAB WASHERS (16) or AIPC 52-32-84-42-200 TAB WASHERS (16) and the fork ends (15) and (25) on the connection rod (18).
(f) Do not fully tighten the jam nuts (17) or safety them with the tab washers (16) at this time.
(3) Make sure the length between the fork ends (15) and (25) of the replacement link assy (26), is as recorded in the removal procedure.
Subtask 52-32-21-420-065-E ** ON A/C NOT FOR ALL (1) Make sure that there are new tab washers (16) on the link assy (26).
(2) If not, replace the tab washers (16) as follows:
(a) Release the tab washers (16) from the jam nuts (17).
(b) Remove the fork ends (15) and (25) from the connection rod (18).
(c) Remove and discard the tab washers (16) from the connection rod (18).
(d) Apply the Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) to the threaded ends of the connection rod (18).
(e) Install the new AIPC 52-32-21-45-200 TAB WASHERS (16) or AIPC 52-32-84-42-200 TAB WASHERS (16) and the fork ends (15) and (25) on the connection rod (18).
(f) Do not fully tighten the jam nuts (17) or safety them with the tab washers (16) at this time.
(3) Make sure the length between the fork ends (15) and (25) of the replacement link assy (26), is as recorded in the removal procedure.
G. Installation of the Switch Mechanism
(1) Install the link assy (26) as follows:
(a) Install the fork end (25) on the drive shaft lever (24) as follows:
1 If removed, install the sleeve (22) in the fork end (25).
2 Put the fork end (25) in position on the drive shaft lever (24) and install the bolt (23), the washer (21) and the nut (20).
3 Tighten the nut (20) and safety it with the new AIPC 52-32-21-45-100 COTTER PIN (19) or AIPC 52-32-84-42-100 COTTER PIN (19).
(b) Install the fork end (15) on the target lever (3) as follows:
1 If removed, install the bush (11) into the fork end (15).
2 Put the fork end (15) on the target lever (3) and install the bolt (10), the washer (12) and the nut (13).
3 Tighten the nut (13) and safety it with the new AIPC 52-32-21-45-150 COTTER PIN (14) or AIPC 52-32-84-42-150 COTTER PIN (14).
(2) Install the target lever (3) as follows:
(a) If removed, install the target (4) with the bolts (5), the washers (2) and the nuts (101) on the target lever (3).
(b) Install the target lever (3) as follows:
1 Put the target lever (3) on the support fitting (9) and install the washer (8) and the nut (7).
2 Tighten the nut (7) and safety it with the new AIPC 52-32-21-45-020 COTTER PIN (6) or AIPC 52-32-84-42-020 COTTER PIN (6).
Subtask 52-32-21-560-054-F ** ON A/C NOT FOR ALL (1) Install the link assy (26) as follows:
(a) Install the fork end (25) on the drive shaft lever (24) as follows:
1 If removed, install the sleeve (22) in the fork end (25).
2 Put the fork end (25) in position on the drive shaft lever (24) and install the bolt (23), the washer (21) and the nut (20).
3 Tighten the nut (20) and safety it with the new AIPC 52-32-21-45-100 COTTER PIN (19) or AIPC 52-32-84-42-100 COTTER PIN (19).
(b) Install the fork end (15) on the target lever (3) as follows:
1 If removed, install the bush (11) into the fork end (15).
2 Put the fork end (15) on the target lever (3) and install the bolt (10), the washer (12) and the nut (13).
3 Tighten the nut (13) and safety it with the new AIPC 52-32-21-45-150 COTTER PIN (14) or AIPC 52-32-84-42-150 COTTER PIN (14).
(2) Install the target lever (3) as follows:
(a) If removed, install the target (4) with the bolts (5), the washers (2) and the nuts (101) on the target lever (3).
(b) Install the target lever (3) as follows:
1 Put the target lever (3) on the support fitting (9) and install the washer (8) and the nut (7).
2 Tighten the nut (7) and safety it with the new AIPC 52-32-21-45-020 COTTER PIN (6) or AIPC 52-32-84-42-020 COTTER PIN (6).
H. Preparation of the Replacement Component
(1) Make sure that there are new locking devices (16) on the link assy (26).
(2) If there are not, replace the locking devices (16) as follows:
(a) Remove the lockwires:
(b) Loosen the jam nuts (17).
(c) Remove the fork ends (15) and (25) and the jam nuts (17) from the connection rod (18).
(d) Remove and discard the locking devices (16) from the connection rod (18).
(e) Apply the Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) to the threaded ends of the connection rod (18).
(f) Install the jam nuts (17), new AIPC 52-32-21-45-210 LOCKING DEVICE (16) or AIPC 52-32-84-42-430 LOCKING DEVICE (16) and the fork ends (15) and (25) on the connection rod (18).
(g) Do not fully tighten the jam nuts (17) or safety them with lockwires to the locking devices (16) at this time.
1 TORQUE the jam nuts (17) and safety them with the lockwires after you adjusted clearance J1 (Para. 4 D step (3)).
(3) Make sure the length between the fork ends (15) and (25) of the replacement link assy (26), is as recorded during the removal procedure.
Subtask 52-32-21-420-065-F ** ON A/C NOT FOR ALL (1) Make sure that there are new locking devices (16) on the link assy (26).
(2) If there are not, replace the locking devices (16) as follows:
(a) Remove the lockwires:
WARNING:
USE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
1 Cut and discard the lockwires from the jam nuts (17) and locking devices (16). (b) Loosen the jam nuts (17).
(c) Remove the fork ends (15) and (25) and the jam nuts (17) from the connection rod (18).
(d) Remove and discard the locking devices (16) from the connection rod (18).
(e) Apply the Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) to the threaded ends of the connection rod (18).
(f) Install the jam nuts (17), new AIPC 52-32-21-45-210 LOCKING DEVICE (16) or AIPC 52-32-84-42-430 LOCKING DEVICE (16) and the fork ends (15) and (25) on the connection rod (18).
(g) Do not fully tighten the jam nuts (17) or safety them with lockwires to the locking devices (16) at this time.
1 TORQUE the jam nuts (17) and safety them with the lockwires after you adjusted clearance J1 (Para. 4 D step (3)).
(3) Make sure the length between the fork ends (15) and (25) of the replacement link assy (26), is as recorded during the removal procedure.
I. Installation of the Switch Mechanism
(1) Install the link assy (26) as follows:
(a) Connect the fork end (25) to the drive shaft lever (24) as follows:
1 If removed, install the bush (22) in the fork end (25).
2 Put the fork end (25) in position on the drive shaft lever (24).
3 Install the bolt (23), the washer (21) and the nut (20).
4 Tighten the nut (20) and safety it with the new AIPC 52-32-21-45-100 COTTER PIN (19) or the new AIPC 52-32-84-42-100 COTTER PIN (19).
(b) Connect the fork end (15) to the target lever (3) as follows:
1 If removed, install the sleeve (11) in the fork end (15).
2 Put the fork end (15) on the target lever (3).
3 Install the bolt (10), the washer (12) and the nut (13).
4 Tighten the nut (13) and safety it with the new AIPC 52-32-21-45-140 COTTER PIN (14) or the new AIPC 52-32-84-42-360 COTTER PIN (14).
(2) Install the target lever (3) as follows:
(a) If removed, install the target (4) together with the bolts (5), the washers (2) and the nuts (1) on the target lever (3).
(b) Install the target lever (3) as follows:
1 Put the target lever (3) on the support fitting (9) and install the washer (8) and the nut (7).
2 Tighten the nut (7) and safety it with the new AIPC 52-32-21-45-020 COTTER PIN (6) or the new AIPC 52-32-84-42-020 COTTER PIN (6).
Subtask 52-32-21-820-058-B ** ON A/C NOT FOR ALL (1) Install the link assy (26) as follows:
(a) Connect the fork end (25) to the drive shaft lever (24) as follows:
1 If removed, install the bush (22) in the fork end (25).
2 Put the fork end (25) in position on the drive shaft lever (24).
3 Install the bolt (23), the washer (21) and the nut (20).
4 Tighten the nut (20) and safety it with the new AIPC 52-32-21-45-100 COTTER PIN (19) or the new AIPC 52-32-84-42-100 COTTER PIN (19).
(b) Connect the fork end (15) to the target lever (3) as follows:
1 If removed, install the sleeve (11) in the fork end (15).
2 Put the fork end (15) on the target lever (3).
3 Install the bolt (10), the washer (12) and the nut (13).
4 Tighten the nut (13) and safety it with the new AIPC 52-32-21-45-140 COTTER PIN (14) or the new AIPC 52-32-84-42-360 COTTER PIN (14).
(2) Install the target lever (3) as follows:
(a) If removed, install the target (4) together with the bolts (5), the washers (2) and the nuts (1) on the target lever (3).
(b) Install the target lever (3) as follows:
1 Put the target lever (3) on the support fitting (9) and install the washer (8) and the nut (7).
2 Tighten the nut (7) and safety it with the new AIPC 52-32-21-45-020 COTTER PIN (6) or the new AIPC 52-32-84-42-020 COTTER PIN (6).
J. Adjustment of the Switch Mechanism
(2) Use the 98D52308002000 CURVED SHIM to measure clearance J1 between the target (365) and the related proximity switch (373) of the door sill area.
Subtask 52-32-21-820-058-C ** ON A/C NOT FOR ALL CAUTION:
BEFORE YOU INSTALL/REMOVE THE GSE-TOOL, READ THE INSTRUCTIONS IN THE APPLICABLE GSE INSTRUCTION MANUAL. WHILE YOU OPERATE THIS TOOL, CAREFULLY OBEY THEM. IF YOU DO NOT OBEY THE INSTRUCTIONS, DAMAGE TO EQUIPMENT CAN OCCUR.
(1) Push the door handle in the recess of the door structure. (2) Use the 98D52308002000 CURVED SHIM to measure clearance J1 between the target (365) and the related proximity switch (373) of the door sill area.
NOTE: Clearance J1 must be between 1.0 mm (0.0394 in.) and 1.8 mm (0.0709 in.).
(3) If clearance J1 is out of tolerance, adjust the proximity switch (373) (Ref. AMM TASK 52-71-00-820-003). J. Adjustment of the Switch Mechanism
(2) Use the 98D52308002000 CURVED SHIM to measure clearance J1 between the target (4) and the related proximity switch (27) of the door sill area.
5. Close-upCAUTION:
BEFORE YOU INSTALL/REMOVE THE GSE-TOOL, READ THE INSTRUCTIONS IN THE APPLICABLE GSE INSTRUCTION MANUAL. WHILE YOU OPERATE THIS TOOL, CAREFULLY OBEY THEM. IF YOU DO NOT OBEY THE INSTRUCTIONS, DAMAGE TO EQUIPMENT CAN OCCUR.
(1) Push the door handle in the recess of the door structure. (2) Use the 98D52308002000 CURVED SHIM to measure clearance J1 between the target (4) and the related proximity switch (27) of the door sill area.
NOTE: Clearance J1 must be between 1.0 mm (0.0394 in.) and 1.8 mm (0.0709 in.).
(3) If clearance J1 is out of tolerance, adjust the proximity switch (27) (Ref. AMM TASK 52-71-00-820-003). Subtask 52-32-21-410-059-B ** ON A/C NOT FOR ALL
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Apply Corrosion Preventive Compound_Water Displacing Soft Film - (Material No.12ABC1) to all the components of the switch mechanism and to the adjacent cargo door structure.
(3) Install access panel 826AR on the cargo door (Ref. AMM TASK 52-31-14-400-801).
(4) Make sure that the cargo door is correctly closed and the door handle is in the LOCKED position (Ref. AMM TASK 52-30-00-860-002).
(5) Remove the access platform(s).
Subtask 52-32-21-410-059-D ** ON A/C NOT FOR ALL (1) Make sure that the work area is clean and clear of tools and other items.
(2) Apply Corrosion Preventive Compound_Water Displacing Soft Film - (Material No.12ABC1) to all the components of the switch mechanism and to the adjacent cargo door structure.
(3) Install access panel 826AR on the cargo door (Ref. AMM TASK 52-31-14-400-801).
(4) Make sure that the cargo door is correctly closed and the door handle is in the LOCKED position (Ref. AMM TASK 52-30-00-860-002).
(5) Remove the access platform(s).
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Apply Corrosion Preventive Compound_Water Displacing Soft Film - (Material No.12ABC1) to all the components of the switch mechanism and to the adjacent cargo door structure.
(3) Install the access panels 826AR and 826BR and the door fairing 826CR on the cargo door (Ref. AMM TASK 52-32-33-400-001).
(4) Make sure that the cargo door is correctly closed and the door handle is in the LOCKED position (Ref. AMM TASK 52-30-00-860-002).
(5) Remove the access platform(s).
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Apply Corrosion Preventive Compound_Water Displacing Soft Film - (Material No.12ABC1) to all the components of the switch mechanism and to the adjacent cargo door structure.
(3) Install the access panels 826AR and 826BR and the door fairing 826CR on the cargo door (Ref. AMM TASK 52-32-33-400-001).
(4) Make sure that the cargo door is correctly closed and the door handle is in the LOCKED position (Ref. AMM TASK 52-30-00-860-002).
(5) Remove the access platform(s).