DOC AIRBUS | AMM A320FReinforcement of Door Seal
TASK 52-32-18-300-002-A
Reinforcement of Door Seal
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Referenced Information
3. Job Set-up
Subtask 52-32-18-010-052-A
Subtask 52-32-18-350-051-A ** ON A/C NOT FOR ALL
Subtask 52-32-18-410-052-A
[Rev.10 from 2021]
2026.04.02 06:28:00 UTC
Reinforcement of Door Seal
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | BLOCK 20X10X10 CM (6.5X3X3 IN)-WOODEN |
| No specific | 1 | CLOTH-EMERY, VERY FINE |
| No specific | 1 | TUBE - PLASTIC, FLEXIBLE, DIA 8 MM (0.3 IN.) MAX. |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.06CED1) | Silicone Adhesive Sealant-Rubber & Plastic Bonding One part - |
| (Material No.06CMD9) | Silicone Adhesive Sealant-General Purpose One part legacy |
| (Material No.14HHB1) | Film-Rubber Bonding Polyester Foil - |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 52-30-00-860-001-A | Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
| TASK 52-30-00-860-002-A | Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
| TASK 52-31-18-000-001-A | Removal of the Door Seal |
| TASK 52-31-18-400-001-A | Installation of the Door Seal |
Reinforcement of Door SealSubtask 52-32-18-010-052-A
A. Get Access
(1) Open the AFT cargo compartment door and safty it with the support struts (Ref. AMM TASK 52-30-00-860-001).
(2) Remove the door seal (Ref. AMM TASK 52-31-18-000-001).
4. Procedure(1) Open the AFT cargo compartment door and safty it with the support struts (Ref. AMM TASK 52-30-00-860-001).
(2) Remove the door seal (Ref. AMM TASK 52-31-18-000-001).
Subtask 52-32-18-350-051-A ** ON A/C NOT FOR ALL
A. Reinforcement of Door Seal
(1) Prepare the door seal as follows:
(a) Make a cut of 60.0 mm (2.3622 in.) length into the root of the door seal between FR54 and FR54A.
(b) Drill stop holes of dia. 2.0 mm (0.0787 in.) at the ends of the cut.
(2) Install the additional silicon tube into the door seal as follows:
(a) Cut the TUBE - PLASTIC, FLEXIBLE, DIA 8 MM (0.3 IN.) MAX. to a length of 3465.0 mm (136.4174 in.).
(b) Push the seal to open the cut.
(c) Carefully introduce the additional silicon tube into the door seal.
(3) Close the cut in the door seal root as follows:
(a) Push the seal to open the cut and very carefully prepare the surfaces of the cut with a CLOTH-EMERY, VERY FINE.
(b) Apply a thin layer of Silicone Adhesive Sealant-General Purpose One part legacy (Material No.06CMD9) or Silicone Adhesive Sealant-Rubber & Plastic Bonding One part - (Material No.06CED1) to the cut area and fill the stop holes.
(c) Press the surfaces of the cut together and leave them to dry for some minutes.
(d) Cover the repair area with a layer of foil Film-Rubber Bonding Polyester Foil - (Material No.14HHB1) and put the seal in the BLOCK 20X10X10 CM (6.5X3X3 IN)-WOODEN.
(e) Compress the seal in the BLOCK 20X10X10 CM (6.5X3X3 IN)-WOODEN with a clamp for a period of 24 hours.
(f) Remove the BLOCK 20X10X10 CM (6.5X3X3 IN)-WOODEN and the foil from the cut area of the seal.
(g) Prepare the cut area with CLOTH-EMERY, VERY FINE to get a smooth surface of the seal.
Subtask 52-32-18-350-051-B ** ON A/C NOT FOR ALL (1) Prepare the door seal as follows:
(a) Make a cut of 60.0 mm (2.3622 in.) length into the root of the door seal between FR54 and FR54A.
(b) Drill stop holes of dia. 2.0 mm (0.0787 in.) at the ends of the cut.
(2) Install the additional silicon tube into the door seal as follows:
(a) Cut the TUBE - PLASTIC, FLEXIBLE, DIA 8 MM (0.3 IN.) MAX. to a length of 3465.0 mm (136.4174 in.).
(b) Push the seal to open the cut.
(c) Carefully introduce the additional silicon tube into the door seal.
(3) Close the cut in the door seal root as follows:
(a) Push the seal to open the cut and very carefully prepare the surfaces of the cut with a CLOTH-EMERY, VERY FINE.
(b) Apply a thin layer of Silicone Adhesive Sealant-General Purpose One part legacy (Material No.06CMD9) or Silicone Adhesive Sealant-Rubber & Plastic Bonding One part - (Material No.06CED1) to the cut area and fill the stop holes.
(c) Press the surfaces of the cut together and leave them to dry for some minutes.
(d) Cover the repair area with a layer of foil Film-Rubber Bonding Polyester Foil - (Material No.14HHB1) and put the seal in the BLOCK 20X10X10 CM (6.5X3X3 IN)-WOODEN.
(e) Compress the seal in the BLOCK 20X10X10 CM (6.5X3X3 IN)-WOODEN with a clamp for a period of 24 hours.
(f) Remove the BLOCK 20X10X10 CM (6.5X3X3 IN)-WOODEN and the foil from the cut area of the seal.
(g) Prepare the cut area with CLOTH-EMERY, VERY FINE to get a smooth surface of the seal.
A. Reinforcement of Door Seal
(1) Prepare the door seal as follows:
(a) Make a cut of 60.0 mm (2.3622 in.) length into the root of the door seal between FR57 and FR57A.
(b) Drill stop holes of dia. 2.0 mm (0.0787 in.) at the ends of the cut.
(2) Install the additional silicon tube into the door seal as follows:
(a) Cut the TUBE - PLASTIC, FLEXIBLE, DIA 8 MM (0.3 IN.) MAX. to a length of 3465.0 mm (136.4174 in.).
(b) Push the seal to open the cut.
(c) Carefully introduce the additional silicon tube into the door seal.
(3) Close the cut in the door seal root as follows:
(a) Push the seal to open the cut and very carefully prepare the surfaces of the cut with a CLOTH-EMERY, VERY FINE.
(b) Apply a thin layer of Silicone Adhesive Sealant-General Purpose One part legacy (Material No.06CMD9) or Silicone Adhesive Sealant-Rubber & Plastic Bonding One part - (Material No.06CED1) to the cut area and fill the stop holes.
(c) Press the surfaces of the cut together and leave them to dry for some minutes.
(d) Cover the repair area with a layer of foil Film-Rubber Bonding Polyester Foil - (Material No.14HHB1) and put the seal in the BLOCK 20X10X10 CM (6.5X3X3 IN)-WOODEN.
(e) Compress the seal in the wooden bonding block with a clamp for a period of 24 hours.
(f) Remove the BLOCK 20X10X10 CM (6.5X3X3 IN)-WOODEN and the foil from the cut area of the seal.
(g) Prepare the cut area with CLOTH-EMERY, VERY FINE to get a smooth surface of the seal.
5. Close-up(1) Prepare the door seal as follows:
(a) Make a cut of 60.0 mm (2.3622 in.) length into the root of the door seal between FR57 and FR57A.
(b) Drill stop holes of dia. 2.0 mm (0.0787 in.) at the ends of the cut.
(2) Install the additional silicon tube into the door seal as follows:
(a) Cut the TUBE - PLASTIC, FLEXIBLE, DIA 8 MM (0.3 IN.) MAX. to a length of 3465.0 mm (136.4174 in.).
(b) Push the seal to open the cut.
(c) Carefully introduce the additional silicon tube into the door seal.
(3) Close the cut in the door seal root as follows:
(a) Push the seal to open the cut and very carefully prepare the surfaces of the cut with a CLOTH-EMERY, VERY FINE.
(b) Apply a thin layer of Silicone Adhesive Sealant-General Purpose One part legacy (Material No.06CMD9) or Silicone Adhesive Sealant-Rubber & Plastic Bonding One part - (Material No.06CED1) to the cut area and fill the stop holes.
(c) Press the surfaces of the cut together and leave them to dry for some minutes.
(d) Cover the repair area with a layer of foil Film-Rubber Bonding Polyester Foil - (Material No.14HHB1) and put the seal in the BLOCK 20X10X10 CM (6.5X3X3 IN)-WOODEN.
(e) Compress the seal in the wooden bonding block with a clamp for a period of 24 hours.
(f) Remove the BLOCK 20X10X10 CM (6.5X3X3 IN)-WOODEN and the foil from the cut area of the seal.
(g) Prepare the cut area with CLOTH-EMERY, VERY FINE to get a smooth surface of the seal.
Subtask 52-32-18-410-052-A
A. Close Access
(1) Install the reinforced door seal (Ref. AMM TASK 52-31-18-400-001).
(2) Close the AFT cargo compartment door (Ref. AMM TASK 52-30-00-860-002).
(1) Install the reinforced door seal (Ref. AMM TASK 52-31-18-400-001).
(2) Close the AFT cargo compartment door (Ref. AMM TASK 52-30-00-860-002).