DOC AIRBUS | AMM A320FInspection of Locking Hooks and Fork Fittings of Aft Cargo Compartment Door at all Frames, between Longeron 4 and Longeron 5 (6 Places)
TASK 52-32-11-200-015-A
Inspection of Locking Hooks and Fork Fittings of Aft Cargo Compartment Door at all Frames, between Longeron 4 and Longeron 5 (6 Places)
Refer to the MPD TASK: 523219-02
GENERAL VISUAL INSPECTION OF LOCKING HOOKS AND FORK FITTINGS OF AFT CARGO COMPARTMENT DOOR AT ALL FRAMES, BETWEEN LONGERON 4 AND LONGERON 5 (6 PLACES)
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 52-32-11-010-071-A ** ON A/C NOT FOR ALL
Subtask 52-32-11-210-067-A ** ON A/C NOT FOR ALL
Subtask 52-32-11-410-071-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.02 06:27:59 UTC
Inspection of Locking Hooks and Fork Fittings of Aft Cargo Compartment Door at all Frames, between Longeron 4 and Longeron 5 (6 Places)
ZONE: 826
1. Reason for the JobRefer to the MPD TASK: 523219-02
GENERAL VISUAL INSPECTION OF LOCKING HOOKS AND FORK FITTINGS OF AFT CARGO COMPARTMENT DOOR AT ALL FRAMES, BETWEEN LONGERON 4 AND LONGERON 5 (6 PLACES)
NOTE: The effectivity of this task is "ALL". To know if this task is applicable for your aircraft, refer to the MPD task applicability and the weight variant data given in the SRM introduction.
2. Job Set-up InformationA. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 826 | AFT CARGO COMPARTMENT DOOR |
| 826AR, 826BR, 826CR |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 51-73-11-300-002-A | Repair of Minor Damage on Titanium, Forged Aluminum, or Steel Components |
| TASK 52-30-00-860-001-A | Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
| TASK 52-30-00-860-002-A | Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
| TASK 52-32-33-000-001-A | Removal of the Door Fairings and Access Panels |
| TASK 52-32-33-400-001-A | Installation of the Door Fairings and Access Panels |
| SRM 517300 | |
| SRM 523200 | |
Locking Hooks and Fork FittingsSubtask 52-32-11-010-071-A ** ON A/C NOT FOR ALL
A. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position below the aft cargo-compartment door.
(2) Remove the door fairing 826CR and the access panels 826AR and 826BR from the cargo door (Ref. AMM TASK 52-32-33-000-001).
(3) Open the aft cargo-compartment door and safety it with the actuator safety lock (Ref. AMM TASK 52-30-00-860-001).
4. Procedure(1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position below the aft cargo-compartment door.
(2) Remove the door fairing 826CR and the access panels 826AR and 826BR from the cargo door (Ref. AMM TASK 52-32-33-000-001).
(3) Open the aft cargo-compartment door and safety it with the actuator safety lock (Ref. AMM TASK 52-30-00-860-001).
Subtask 52-32-11-210-067-A ** ON A/C NOT FOR ALL
A. General Visual Inspection Procedure
(1) Clean the component interfaces and the adjacent area.
(2) Make sure the locking hooks are correctly installed.
(3) Examine the locking hooks for corrosion, cracks, distortion, fretting, gouges, nicks, scratches, other damage.
(a) If you find corrosion, cracks, distortion, fretting, gouges, nicks, scratches or other damage, do as follows:
1 Find the dimensions of the damage and the permitted limits SRM 523200.
2 If the damage that is less than the limit, repair the damage (Ref. AMM TASK 51-73-11-300-002).
3 If the damage is more than the limit, replace the locking hook (Ref. AMM TASK 52-32-21-000-007).
(4) Make sure the bushes and bolt assemblies of the locking hook mechanisms are correctly installed.
(5) Examine the bushes and bolts of the locking hook mechanisms for corrosion, cracks, gouges, nicks, scratches, wear or damage.
(a) If you find corrosion, cracks, gouges, nicks, scratches, wear or other damage:
1 Find the dimensions of the damage and the permitted limits SRM 523200.
2 If the damage is less than the limit, repair the damage (Ref. AMM TASK 51-73-11-300-002).
3 If the damage is more than the limit, replace the applicable parts of the locking hook mechanism (Ref. AMM TASK 52-32-21-000-007).
(6) Examine the fork fitting assemblies for corrosion, cracks, distortion, fretting, gouges, nicks, scratches or other damage.
(a) If you find corrosion, cracks, distortion, fretting, gouges, nicks, scratches or other damage, do as follows:
1 Find the dimensions of the damage and the permitted limits SRM 523200.
2 If the damage is less than the limit, rempair the damage SRM 517300.
3 If the damage is more than the limit, repair/replace the fork fitting assemblies as necessary SRM 523200.
5. Close-up(1) Clean the component interfaces and the adjacent area.
(2) Make sure the locking hooks are correctly installed.
(3) Examine the locking hooks for corrosion, cracks, distortion, fretting, gouges, nicks, scratches, other damage.
(a) If you find corrosion, cracks, distortion, fretting, gouges, nicks, scratches or other damage, do as follows:
1 Find the dimensions of the damage and the permitted limits SRM 523200.
2 If the damage that is less than the limit, repair the damage (Ref. AMM TASK 51-73-11-300-002).
3 If the damage is more than the limit, replace the locking hook (Ref. AMM TASK 52-32-21-000-007).
(4) Make sure the bushes and bolt assemblies of the locking hook mechanisms are correctly installed.
(5) Examine the bushes and bolts of the locking hook mechanisms for corrosion, cracks, gouges, nicks, scratches, wear or damage.
(a) If you find corrosion, cracks, gouges, nicks, scratches, wear or other damage:
1 Find the dimensions of the damage and the permitted limits SRM 523200.
2 If the damage is less than the limit, repair the damage (Ref. AMM TASK 51-73-11-300-002).
3 If the damage is more than the limit, replace the applicable parts of the locking hook mechanism (Ref. AMM TASK 52-32-21-000-007).
(6) Examine the fork fitting assemblies for corrosion, cracks, distortion, fretting, gouges, nicks, scratches or other damage.
(a) If you find corrosion, cracks, distortion, fretting, gouges, nicks, scratches or other damage, do as follows:
1 Find the dimensions of the damage and the permitted limits SRM 523200.
2 If the damage is less than the limit, rempair the damage SRM 517300.
3 If the damage is more than the limit, repair/replace the fork fitting assemblies as necessary SRM 523200.
Subtask 52-32-11-410-071-A ** ON A/C NOT FOR ALL
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the actuator safety lock and close the AFT cargo-compartment door (Ref. AMM TASK 52-30-00-860-002).
(3) Instal the access panels 826AR and 826BR and the door fairing 826CR on the cargo door (Ref. AMM TASK 52-32-33-400-001).
(4) Remove the access platform(s).
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the actuator safety lock and close the AFT cargo-compartment door (Ref. AMM TASK 52-30-00-860-002).
(3) Instal the access panels 826AR and 826BR and the door fairing 826CR on the cargo door (Ref. AMM TASK 52-32-33-400-001).
(4) Remove the access platform(s).