Installation of the Door Damper and Emergency Operation Cylinder

TASK 52-22-14-400-001-A
Installation of the Door Damper and Emergency Operation Cylinder

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 830
ZONE: 840
FIN: 1600WM ** ON A/C NOT FOR ALL
FIN: 1601WM ** ON A/C NOT FOR ALL
FIN: 1602WM ** ON A/C NOT FOR ALL
FIN: 1603WM ** ON A/C NOT FOR ALL

1. Reason for the Job

NOTE: The steps related to the Cabin Intercommunication Data System (CIDS) are only applicable on aircraft when the related door damper and emergency cylinder is connected to the CIDS.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE
No specific	AR	PENCIL - SHARP

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
830	L PASSENGER/CREW DOORS & EMERGENCY EXITS
840	R PASSENGER/CREW DOORS & EMERGENCY EXITS

C. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
14	COTTER PIN	AIPC 52-22-02-03-090
6	COTTER PIN	AIPC 52-22-02-03-190
14	COTTER PIN	AIPC 52-22-04-03-090
6	COTTER PIN	AIPC 52-22-04-03-190
66	TAB WASHER	AIPC 52-22-22-06-170

D. Referenced Information

REFERENCE	DESIGNATION
TASK 20-28-00-912-802-A	Electrical Bonding - General Maintenance Procedure
TASK 23-73-00-740-005-A	BITE-Test of the Cabin Intercommunication Data System (CIDS) through the CFDS
TASK 23-73-00-740-005-B	Interface and Power-Up Test of the Cabin Intercommunication Data System (CIDS) through the CFDS
TASK 25-23-47-000-012-A	Removal of the Door Linings of the LH FWD Emergency Exit Door, zone 231
TASK 25-23-47-000-013-A	Removal of the Door Linings of the RH FWD Emergency Exit Door at zone 251 or RH AFT at zone 252 or LH AFT at zone 232.
TASK 25-23-47-000-802-A	Removal of the Door Linings of the Emergency Exit, zones 251/252
TASK 25-23-47-400-012-A	Installation of the Door Linings of the LH FWD Emergency Exit Door, zone 231
TASK 25-23-47-400-013-A	Installation of the Door Linings of the RH FWD Emergency Exit Door at zone 251, or RH AFT at zone 252, or LH AFT at zone 232.
TASK 25-23-47-400-802-A	Installation of the Door Linings of the Emergency Exit, zones 251/252
TASK 26-10-00-740-801-A	BITE Test of the Smoke Detection Function - System Test
TASK 52-22-00-010-001-A	Opening of the Emergency Exit Doors from the Passenger Compartment
TASK 52-22-00-410-001-A	Closing of the Emergency Exit Doors from the Passenger Compartment
TASK 52-22-00-614-002-A	Charging of the Door Damper and Emergency Operation Cylinders at the Emergency Exit Doors
TASK 52-22-00-860-003-A	Special Precaution before Maintenance on the Door Damper and Emergency Operation Cylinder
TASK 52-22-00-860-004-A	Special Precaution after Maintenance on the Door Damper and Emergency Operation Cylinder
Door Damper and Emergency Operation Cylinder ** ON A/C NOT FOR ALL
Door Damper and Emergency Operation Cylinder ** ON A/C NOT FOR ALL
Adjustment of the Release Travel

3. Job Set-up
Subtask 52-22-14-860-050-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Make sure that the applicable emergency exit door (referred to as the door) is opened as necessary, but not fully (Ref. AMM TASK 52-22-00-010-001).
(2) Make sure that the ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE is in position below the door.
(3) Make sure that the special precaution procedure for the door damper and emergency operation cylinder is completed (Ref. AMM TASK 52-22-00-860-003).
(4) Make sure that the applicable door lining is removed (Ref. AMM TASK 25-23-47-000-012) or (Ref. AMM TASK 25-23-47-000-013)

Subtask 52-22-14-860-050-CS ** ON A/C NOT FOR ALL

Subtask 52-22-14-865-051-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	COM/CIDS/DEU B/ESS	153RH	G03
** ON A/C NOT FOR ALL
121VU	COM NAV/CIDS/DEU B NORM/R	620RH	M08
121VU	COM NAV/CIDS/DEU B NORM/L	619RH	M07
** ON A/C NOT FOR ALL
121VU	COM NAV/CIDS/DEU B/NORM	162RH	M09

4. Procedure

WARNING: BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:

THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
THE PERCUSSION LEVER OF THE DOOR-DAMPER AND EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.

IF YOU DO NOT OBEY THESE INSTRUCTIONS, THE DOOR CAN OPEN WITH FORCE OR THE ESCAPE SLIDE CAN DEPLOY SUDDENLY. THIS CAN CAUSE INJURY AND/OR DAMAGE.

Subtask 52-22-14-910-050-A ** ON A/C NOT FOR ALL

A. Preparation for Installation
(1) Make sure that the parts retained from the removed component are clean and in the correct condition.
(2) Examine the bushes (3) and (8) of the support arm fitting (7) for damage.
(3) Make sure that the bushes of the yoke assembly (18) and the telescopic rod assembly (21) are in the correct condition.
(4) Clean the component interfaces and the adjacent area.
(5) Do an inspection of the component interfaces and the adjacent area.

Subtask 52-22-14-420-051-B ** ON A/C NOT FOR ALL

B. Installation of the Door Damper and Emergency Operation Cylinder
(1) Put the door damper and emergency operation cylinder (referred to as the door damper) (1) in position between the support arm fitting (7) and the yoke assembly (18).
(2) Install the door damper (1) on the support arm fitting (7) as follows:
(a) Put the safety plates (2) in position at the rod end of the door damper (1).
(b) Install the rod-end together with the safety plates (2) in the support arm fitting (7).
(c) Install the bolt (10) with the washer (9) on the support arm fitting (7).
(d) Install the washer (4) and the nut (5).
(e) Tighten the nut (5).
(f) Safety the nut (5) with the new AIPC 52-22-02-03-190 COTTER PIN (6) or the new AIPC 52-22-04-03-190 COTTER PIN (6).
(3) Install the door damper (1) on the yoke assembly (18) as follows:
(a) Put the piston rod of the door damper (1) in position at the yoke assembly (18) and the telescopic rod assembly (21).
(b) Install the bolt (20) with the washer (19).
(c) Install the spacer (17), the washer (16) and the nut (15) on the bolt (20).
(d) Tighten the nut (15).
(e) Safety the nut (15) with the new AIPC 52-22-02-03-090 COTTER PIN (14) or the new AIPC 52-22-04-03-090 COTTER PIN (14).
(4) Connect the bonding strap (11) to the door damper (1) with the screw (13) and the washer (12) (Ref. AMM TASK 20-28-00-912-802).
(5) Remove the CAP-BLANKING from each electrical connector and receptacle.
(6) Release the temporarily attached cable loom from the support arm.
(7) Connect the applicable connector (22) to the related receptacle (24) (refer to the table that follows):

----------------------------------------------------------------------

! DOOR ! CONNECTOR ! DOOR DAMPER ! FRAME ! CABLE LOOM !

----------------------------------------------------------------------

! FWD LH ! 360RH5-A ! 1600WM ! FR35 ! 4251VB !

! FWD RH ! 360RH6-A ! 1601WM ! FR35 ! 4250VB !

! AFT LH ! 360RH7-A ! 1602WM ! FR47.2 ! 4253VB !

! AFT RH ! 360RH8-A ! 1603WM ! FR47.2 ! 4252VB !

----------------------------------------------------------------------

(8) Fill the pressure accumulator of the door damper (1) with nitrogen to 123 bar (1784 psi) (Ref. AMM TASK 52-22-00-614-002).
(9) Close and open the door a number of times to make sure that the door damper (1) operates satisfactorily.

Subtask 52-22-14-420-051-C ** ON A/C NOT FOR ALL

B. Installation of the Door Damper and Emergency Operation Cylinder
(1) Put the door damper and emergency operation cylinder (referred to as the door damper) (1) in position between the support arm fitting (7) and the yoke assembly (18).
(2) Install the door damper (1) on the support arm fitting (7) as follows:
(a) Put the safety plates (2) in position at the rod end of the door damper (1).
(b) Install the rod-end together with the safety plates (2) in the support arm fitting (7).
(c) Install the bolt (10) with the washer (9) on the support arm fitting (7).
(d) Install the washer (4) and the nut (5).
(e) Tighten the nut (5).
(f) Safety the nut (5) with the new AIPC 52-22-04-03-190 COTTER PIN (6).
(3) Install the door damper (1) on the yoke assembly (18) as follows:
(a) Put the piston rod of the door damper (1) in position at the yoke assembly (18) and the telescopic rod assembly (21).
(b) Install the bolt (20) with the washer (19).
(c) Install the spacer (17), the washer (16) and the nut (15) on the bolt (20).
(d) Tighten the nut (15).
(e) Safety the nut (15) with the new AIPC 52-22-04-03-090 COTTER PIN (14).
(4) Connect the bonding strap (11) to the door damper (1) with the screw (13) and the washer (12) (Ref. AMM TASK 20-28-00-912-802).
(5) Remove the CAP-BLANKING from each electrical connector and receptacle.
(6) Release the temporarily attached cable loom from the support arm.
(7) Connect the applicable connector (22) to the related receptacle (24) (refer to the table that follows):

DOOR	CONNECTOR	RECEPTACLE	FRAME	CABLE LOOM
LH	360RH7-A	1602WM	FR48A	4253VB
RH	360RH8-A	1603WM	FR48A	4252VB

Subtask 52-22-14-820-050-A ** ON A/C NOT FOR ALL

C. Adjustment of the Release Travel between the Door Damper and the Operation Lever

Adjustment of the Release Travel ** ON A/C NOT FOR ALL

(1) Make sure that the related door is correctly closed (Ref. AMM TASK 52-22-00-410-001).
(2) Make sure that the door damper is in this condition:

The release lever (63) of the door damper is fully retracted in its safetied position.
The percussion mechanism of the door damper is blocked with the related 701-2978000 PIN-SAFETY, PAX DOOR DAMPER (69).

(3) Make sure that the inflation reservoir is in this condition (Ref. AMM TASK 52-22-00-010-001):

Its operation valve is safetied with the related lock pin.
Its release cable is disconnected from the release lever.

(4) Measure the distance "U" between the lower edge of the release lever (63) and the top of the stop bolt (64) as follows:
(a) Pull up the inboard handle until the door lifts but do not open it at this stage.
(b) Set the slide control handle to the ARMED position.
(c) Loosen the knurled screw (62) and carefully extend the release lever (63) until it touches the stop bolt (64).
(d) Put a mark on the stop bolt (64) to show the position of the lower edge of the release lever (63).

NOTE: It is necessary to use a PENCIL - SHARP to make the mark on the stop bolt (64).

(e) Retract the release lever (63) and safety it with the knurled screw (62).
(f) Measure the distance between the pencil mark and the top of the stop bolt (64):

NOTE: The dimension must be between 5.5 mm (0.2165 in.) and 6.5 mm (0.2559 in.).

(5) If the distance "U" is out of tolerance, adjust the position of the stop bolt (64) as follows:
(a) If necessary, bend the tab washer (66) to release the adjustment nut (65).

NOTE: If you must do this, replace the AIPC 52-22-22-06-170 TAB WASHER (66).

(b) Loosen the jam nut (68) and the adjustment nut (65).
(c) Turn the stop bolt (64) as necessary until the distance "U" is correct.
(d) Tighten the adjustment nut (65) and the jam nut (68).
(e) Safety the adjustment nut (65) with the tab washer (66).

Subtask 52-22-14-865-052-A ** ON A/C NOT FOR ALL

D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	COM/CIDS/DEU B/ESS	153RH	G03
** ON A/C NOT FOR ALL
121VU	COM NAV/CIDS/DEU B NORM/R	620RH	M08
121VU	COM NAV/CIDS/DEU B NORM/L	619RH	M07
** ON A/C NOT FOR ALL
121VU	COM NAV/CIDS/DEU B/NORM	162RH	M09

Subtask 52-22-14-740-050-A ** ON A/C NOT FOR ALL

E. Tests
(1) Do the interface and power-up test of the CIDS (Ref. AMM TASK 23-73-00-740-005).
(2) Do the BITE test of the CIDS (Ref. AMM TASK 23-73-00-740-005).

Subtask 52-22-14-740-051-A ** ON A/C NOT FOR ALL

F. BITE Test of the Smoke Detection Function (SDF)
(1) Do the BITE test of the SDF (Ref. AMM TASK 26-10-00-740-801).

5. Close-up
Subtask 52-22-14-410-050-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the removed door lining (Ref. AMM TASK 25-23-47-400-012) or (Ref. AMM TASK 25-23-47-400-013)
(3) Do the special precaution for the door damper and emergency operation cylinder (Ref. AMM TASK 52-22-00-860-004).
(4) Make sure that the related door is correctly closed and the inflation reservoir is serviceable (Ref. AMM TASK 52-22-00-410-001).
(5) Remove the access platform(s).

Subtask 52-22-14-410-050-CS ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the removed door lining (Ref. AMM TASK 25-23-47-400-802).
(3) Do the special precaution for the door damper and emergency operation cylinder (Ref. AMM TASK 52-22-00-860-004).
(4) Make sure that the related door is correctly closed and the inflation reservoir is serviceable (Ref. AMM TASK 52-22-00-410-001).
(5) Remove the access platform(s).

[Rev.10 from 2021] 2026.04.02 06:27:41 UTC