Installation of the Release Mechanism of the Emergency Escape Slide of the Aft Passenger/Crew Door

TASK 52-13-22-400-001-A
Installation of the Release Mechanism of the Emergency Escape Slide of the Aft Passenger/Crew Door

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	GUN - GREASE
No specific	Torque wrench: range to between 0.35 and 0.3 m.daN (30.97 and 26.55 lbf.in )
No specific	Torque wrench: range to between 0.44 and 0.36 m.daN (38.94 and 31.86 lbf.in )
No specific	Torque wrench: range to between 0.7 and 0.6 m.daN (61.95 and 53.10 lbf.in )
No specific	Torque wrench: range to between 1.2 and 1 m.daN (106.19 and 88.50 lbf.in )
No specific	Torque wrench: range to between 1.32 and 1.08 m.daN (116.81 and 95.58 lbf.in )
98DNSA20206060	1	RIGGING PIN
OR	OR
98DNSA20206120	1	RIGGING PIN

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.03HBD9)	Synthetic Ester base Grease-General Purpose Low Temp -
(Material No.03JBA1)	Silicone base Grease-General Purpose - -
(Material No.04EAC2)	Primer Polyurethane Paint_- Corrosion Inhibiting Structure
(Material No.04JME4)	Top Coat Polyurethane_- Grey Internal Structure
(Material No.06AAB1)	Polysulfide Sealant-General Purpose Fillet -
(Material No.06AEB2)	Polysulfide Sealant-Low Adhesion Fillet Structure
(Material No.06LCG9)	Non Hardening Jointing Putty-Medium Temp. Area - -
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.12ABE2)	Corrosion Preventive Compound-Water Displacing Oily Film System
(Material No.12ACC1)	Corrosion Preventive Compound-Heavy Duty Soft Film -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
832AZ, 832BZ, 832CZ, 832DZ, 832EZ, 832FZ, 832GZ

D. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
16	COTTER PIN	AIPC 52-11-22-02-010
7	COTTER PIN	AIPC 52-11-22-02-010
190	COTTER PIN	AIPC 52-13-11-10-010
193	COTTER PIN	AIPC 52-13-11-10-010
195	COTTER PIN	AIPC 52-13-11-10-010
149	COTTER PIN	AIPC 52-13-22-01-010
166	COTTER PIN	AIPC 52-13-22-01-010
173	COTTER PIN	AIPC 52-13-22-01-010
85	COTTER PIN	AIPC 52-13-22-01-010
95	COTTER PIN	AIPC 52-13-22-01-010
169	COTTER PIN	AIPC 52-13-22-01-360
15	COTTER PIN	AIPC 52-13-22-02-010
25	COTTER PIN	AIPC 52-13-22-02-010
3	COTTER PIN	AIPC 52-13-22-02-010
39	COTTER PIN	AIPC 52-13-22-02-010
52	COTTER PIN	AIPC 52-13-22-03-010
58	COTTER PIN	AIPC 52-13-22-03-010
190	COTTER PIN	AIPC 52-13-84-12-010
193	COTTER PIN	AIPC 52-13-84-12-010
195	COTTER PIN	AIPC 52-13-84-12-010
149	COTTER PIN	AIPC 52-13-84-30-010
166	COTTER PIN	AIPC 52-13-84-30-010
173	COTTER PIN	AIPC 52-13-84-30-010
85	COTTER PIN	AIPC 52-13-84-30-010
95	COTTER PIN	AIPC 52-13-84-30-010
169	COTTER PIN	AIPC 52-13-84-30-360

E. Referenced Information

REFERENCE	DESIGNATION
TASK 24-42-00-861-001-A	Energize the Ground Service Network from the External Power
TASK 24-42-00-862-001-A	De-energize the Ground Service Network Supplied from the External Power
TASK 25-23-46-400-002-A	Installation of the Door Linings on the Aft Passenger/Crew Doors
TASK 25-62-44-400-006-A	Installation of the Left Escape-Slide Pack-Assembly
TASK 25-62-44-400-007-A	Installation of the Left-Hand Escape-Slide-Raft Pack-Assembly
TASK 25-62-44-400-802-A	Installation of the Right Escape-Slide Pack-Assembly
TASK 25-62-44-400-803-A	Installation of the Right-Hand Escape-Slide-Raft Pack-Assembly
TASK 52-10-00-860-001-A	Special Precautions before Work on the Passenger/Crew Door
TASK 52-10-00-860-002-A	Special Precautions after Work on the Passenger/Crew Door
TASK 52-13-14-820-002-A	Adjustment of the Percussion Bellcrank Finger of the Door Damper and Emergency Operation Cylinder of the AFT Passenger/Crew Door
TASK 52-13-22-220-001-A	Detailed Visual Inspection of the Release Mechanism of the Emergency Escape Slide of the Aft Passenger/Crew Door
TASK 52-13-22-820-001-A	Adjustment/Test of the Release Mechanism of the Emergency Escape Slide
TASK 52-71-00-820-002-A	Adjustment of the Proximity Switches of the Passenger/Crew Doors with the Doors Checking Tool
TASK 52-71-00-820-002-A-01	Adjustment of the Proximity Switches of the Passenger/Crew Doors with the ECAM Display Unit (DU)
Telescopic Forks and Control Shaft
Percussion System
Percussion System - Rigging Point Location
Flexible Control
Flexible Control - Record of Dimensions
Escape Slide Gearbox
Escape Slide Gearbox - Telescopic Rod Adjustment
Plate Assembly
Control Handle of the Emergency Escape Slide
Escape Slide Control Mechanism
Escape Slide Control Mechanism - Adjustment

3. Job Set-up
Subtask 52-13-22-860-050-A

A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized (Ref. AMM TASK 24-42-00-861-001).
(2) Make sure that the door linings and the insulation are removed.
(3) Obey the special precautions before you start work on the door (Ref. AMM TASK 52-10-00-860-001).
(4) Make sure that the parts retained from the removed component are clean and in the correct condition.

Subtask 52-13-22-865-051-A

B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
121VU	EIS/SLIDES/ARM AND WARN/FLT	15WN	P11
121VU	EIS/SLIDES/ARM AND WARN/GND	13WN	P10
121VU	EIS/SDAC1 AND 2/DOOR/DET/PAX	48WV	P05

Subtask 52-13-22-110-050-A

C. Cleaning
(1) Clean the component interfaces and the adjacent area.
(2) Clean all the other components with Non Aqueous Cleaner-General - - (Material No.08BAA9) and Textile-Lint free Cotton - (Material No.14SBA1) .
(3) Do an inspection of the component interfaces and the adjacent area.
(4) Make sure that the parts retained from the removed component are clean and in the correct condition.
(Ref. AMM TASK 52-13-22-220-001)

4. Procedure
Subtask 52-13-22-420-050-A

A. Installation of the Girt Bar Control Shaft

Telescopic Forks and Control Shaft

(1) Put the bellcrank (155) and the spacer (159) in position.
(2) Install the shaft (167).
(3) Install the taper pins (154), (160) with Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) .
(4) Install the washers (156), (161), the nuts (157), (158) and tighten them.
(5) Install the levers (145), (164) on the shaft (167).
(6) Install the taper pins (144), (165) with Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) .
(7) Install the washers (147), (163), the nuts (146), (162) and tighten them.
(8) Put the flexible control (152) in position.
(9) Install the washer (151), the bolt (153), the washer (150) and the nut (148).
(10) TORQUE the nut (148) to between 0.35 and 0.3 m.daN (30.97 and 26.55 lbf.in )

NOTE: If you install a new bolt (153) drill a hole of 1.9 mm (0.0748 in.).

(11) Install the AIPC 52-13-22-01-010 COTTER PIN (149) or AIPC 52-13-84-30-010 COTTER PIN (149).
(12) Install the telescopic forks (143), the bolts (140), the nuts (142).
(13) TORQUE the nuts (142) to between 0.35 and 0.3 m.daN (30.97 and 26.55 lbf.in )

Subtask 52-13-22-420-051-A

B. Installation of the Percussion System

Percussion System

Percussion System - Rigging Point Location

(1) Install the bellcrank assembly (176), the bolt (181) the washers (180), (179), and the nut (170).
(2) TORQUE the nut (170) to between 1.2 and 1 m.daN (106.19 and 88.50 lbf.in )

.
(3) Install the cotter pin AIPC 52-13-22-01-360 COTTER PIN (169) or AIPC 52-13-84-30-360 COTTER PIN (169).

NOTE: If you install a new bolt (181) drill a hole of 2.8 mm (0.1102 in.).

(4) Install the bolt (178) and the washer (177). Apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) on the bolt shank and install the rod (184), the washer (175) and the nut (74).
(5) TORQUE the nut (174) to between 0.35 and 0.3 m.daN (30.97 and 26.55 lbf.in )

NOTE: If you install a new bolt (178) drill a hole of 1.9 mm (0.0748 in.).

(6) Install the AIPC 52-13-22-01-010 COTTER PIN (173) or AIPC 52-13-84-30-010 COTTER PIN (173).
(7) Rig the triple lever with the 98DNSA20206060 RIGGING PIN98DNSA20206120 RIGGING PIN and put the escape slide control handle in the ARMED position.

NOTE: The 98DNSA20206120 RIGGING PIN is an alternative to the 98DNSA20206060 RIGGING PIN. But, because of its length, you cannot use the 98DNSA20206120 RIGGING PIN at all the location.

(8) Put the rod (160) in position and adjust its length if necessary.
(9) Install the bolt (186), the washer (185) and apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) on the bolt shanks.
(10) Install the rods (160) and (184), the flexible control (168), the washers (165) and the nuts (167).
(11) TORQUE the nuts (167) to between 0.35 and 0.3 m.daN (30.97 and 26.55 lbf.in )

.
(12) Install the AIPC 52-13-22-01-010 COTTER PIN (166) or AIPC 52-13-84-30-010 COTTER PIN (166).
(13) Remove the 98DNSA20206060 RIGGING PIN98DNSA20206120 RIGGING PIN.

Subtask 52-13-22-420-052-C

C. Installation of the Flexible Control Assembly

Flexible Control

Flexible Control - Record of Dimensions

(1) Remove the grease nipple (91) from the new flexible control (108).
(2) Assembly of the flexible control
(a) Install the nut (109) on the flexible control (108).
(b) Install the washer (110).
(c) Install the nut (107) on the flexible control (108).
(3) Installation of the flexible control (108)
(a) Before installation, slightly bend the flexible control (108) to its final shape.
(b) Put the flexible control (108) into the hole at the bottom of the door.
(c) Engage the flexible control (108) in the fitting (118).
(d) Install the grease nipple (91) on the new flexible control (108).
(e) Make sure that the dimension X5 between the flexible control (108) and the grease nipple (91) is 1 mm (0.0394 in.).

NOTE: When you install the flexible control (108), make sure that the grease nipples (89) and (91) point inboard.

(f) Install the washer (104), the fitting (87) and the washer (106) on the flexible control (108).
(g) Install the nut (105) on the flexible control (108).
(h) Put the nut (107) in position so that you get the dimension X2.
(i) TORQUE the nuts (107) and (105) to between 1.32 and 1.08 m.daN (116.81 and 95.58 lbf.in )

.
(j) Install the seal nut (103).
(k) TORQUE the seal nut (103) to between 0.44 and 0.36 m.daN (38.94 and 31.86 lbf.in )

.
(l) Install the nut (102), the lockwasher (101) and the eye end assembly (100).
(m) Put the nut (102) in position so that you get the dimension X1.
(n) TORQUE the nut (102) to between 0.7 and 0.6 m.daN (61.95 and 53.10 lbf.in )

.
(o) Safety the nut (102) with the lockwasher (101).
(p) Install the washer (112).
(q) Install the nut (113) on the flexible control (108).
(r) Put the nut (109) in position so that you get the dimension X3.
(s) TORQUE the nuts (109), (113) to between 1.32 and 1.08 m.daN (116.81 and 95.58 lbf.in )

.
(t) Install the seal nut (114).
(u) TORQUE the seal nut (114) to between 0.44 and 0.36 m.daN (38.94 and 31.86 lbf.in )

.
(v) Install the nut (115), the lockwasher (116) and the eye end assembly (117).
(w) Put the nut (115) in position so that you get the dimension X4.
(x) TORQUE the nut (115) to between 0.7 and 0.6 m.daN (61.95 and 53.10 lbf.in )

.
(y) Safety the nut (115) with the lockwasher (117).
(4) Apply Polysulfide Sealant-General Purpose Fillet - (Material No.06AAB1) on contact surfaces between the fitting (87) and the door structure.
(5) Install the bolts (88) and the nuts (86).
(6) Tighten the nuts (86).
(7) Install the bolts (80), the washers (81), (83) and the nut (84).
(8) TORQUE the nut (84) to between 0.35 and 0.3 m.daN (30.97 and 26.55 lbf.in )

NOTE: If you install a new bolt (80) drill a hole of 1.9 mm (0.0748 in.).

(9) Install a new AIPC 52-13-22-01-010 COTTER PIN (85) or AIPC 52-13-84-30-010 COTTER PIN (85).
(10) Install the bolt (92), the washers (93), (96) and the nut (94).
(11) TORQUE the nut (94) to between 0.35 and 0.3 m.daN (30.97 and 26.55 lbf.in )

NOTE: If you install a new bolt (94) drill a hole of 1.9 mm (0.0748 in.).

(12) Install a new AIPC 52-13-22-01-010 COTTER PIN (95) or AIPC 52-13-84-30-010 COTTER PIN (95).

Subtask 52-13-22-640-051-A

D. Lubrication of the Flexible Control Assembly

Flexible Control

(1) Loosen the seal nut (114) by three turns minimum.
(2) Connect a GUN - GREASE to the grease nipple (91). Apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) until it comes out of the holes in the seal nut (114).
(3) TORQUE the seal nut (114) to between 0.44 and 0.36 m.daN (38.94 and 31.86 lbf.in )

.
(4) Loosen the seal nut (103) by three turns minimum and make sure that you can see the grease.
(5) If not, connect a GUN - GREASE to the grease nipple (89). Apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) until it comes out of the holes in the seal nut (103).
(6) TORQUE the seal nut (103) to between 0.44 and 0.36 m.daN (38.94 and 31.86 lbf.in )

Subtask 52-13-22-420-053-A

E. Installation of the Escape Slide Gear Box

Escape Slide Gearbox

Escape Slide Gearbox - Telescopic Rod Adjustment

Plate Assembly

(1) Install the escape slide gear box (60) and apply Polysulfide Sealant-Low Adhesion Fillet Structure (Material No.06AEB2) on contact surfaces between the escape slide gear box and the door structure.
(2) Install the washers (61), the bolts (62) and tighten them.
(3) Install the washer (63), the bolt (64) and tighten it.
(4) Put the inner control handle and the outer control handle in the locked-down position.
(5) Put the emergency control handle in the ARMED position.
(6) Install a 98DNSA20206060 RIGGING PIN98DNSA20206120 RIGGING PIN.

NOTE: The 98DNSA20206120 RIGGING PIN is an alternative to the 98DNSA20206060 RIGGING PIN. But, because of its length, you cannot use the 98DNSA20206120 RIGGING PIN at all the location.

(7) Keep the contact between the cam (66) and the lower part of the roller (67).
(8) Measure the dimension X1 when the operations above are completed.
(9) Adjust the length of the rod (54) in the maximum extended position so that the length is equal to X1+ 0.1 +0.1 mm or -0.1 mm (0.0039 +0.0039 in. or -0.0039 in.).
(10) Make sure that the clearance X2 is 0 +0.1 mm or +1.5 mm (0.0000 +0.0039 in. or +0.0591 in.).
(11) Put the rod (54) in position.
(12) Install the washers (50), (51), the bolt (49) and the nut (53).
(13) TORQUE the nut (53) to between 0.35 and 0.3 m.daN (30.97 and 26.55 lbf.in )

NOTE: If you install a new bolt (49), drill a hole of 1.9 mm (0.0748 in.).

(14) Install the AIPC 52-13-22-03-010 COTTER PIN (52).
(15) Install the bolt (55), the washers (56), (57), the nut (59) and tighten it.

NOTE: If you install a new bolt (55), drill a hole of 2 mm (0.0787 in.).

(16) Install the AIPC 52-13-22-03-010 COTTER PIN (58).
(17) Install the plate assembly (72) as follow.
(a) Apply a coat of Polysulfide Sealant-Low Adhesion Fillet Structure (Material No.06AEB2) on the contact surface between the plate assembly and the door structure.
(b) Put the plate assembly in position.
(c) Install the washers (71) and the bolts (70).
(d) Tighten the bolts (70).
(18) Remove the 98DNSA20206060 RIGGING PIN98DNSA20206120 RIGGING PIN.

Subtask 52-13-22-420-054-B

F. Installation of the Emergency Control Handle

Control Handle of the Emergency Escape Slide

Percussion System - Rigging Point Location

(1) Install the rod (32) on bellcrank (24).
(2) Install the washer (45), the bolt (47), connect the rod (32). Install the washer (30) and the nut (29).
(3) TORQUE the nut (29) to between 0.35 and 0.3 m.daN (30.97 and 26.55 lbf.in )

NOTE: : If you install a new bolt (47) drill a hole of 1.9 mm (0.0748 in.)

(4) Install a cotter pin (28).
(5) Put the bellcrank (24), the spacer (23) and the washers (22) in position.
(6) Install the escape slide handle axle (19).
(7) Install the taper pin (31), the washer (6), the nut (8) and the AIPC 52-11-22-02-010 COTTER PIN (7).
(8) Install the emergency control handle (21).
(9) Install the taper pin (20), the washer (18), the nut (17) and the AIPC 52-11-22-02-010 COTTER PIN (16).
(10) Install the lever (1).
(11) Install the taper pin (2), the washer (5), the nut (4) and the AIPC 52-13-22-02-010 COTTER PIN (3).
(12) Install the washer (12), the bolt (11), connect the telescopic rod (10).
(13) Install the washer (13), the nut (14).
(14) TORQUE the nut (14) to between 0.35 and 0.3 m.daN (30.97 and 26.55 lbf.in )

NOTE: If you install a new bolt (11) drill of 1.9 mm (0.0748 in.).

(15) Install a new AIPC 52-13-22-02-010 COTTER PIN (15).
(16) Rig the triple lever with 98DNSA20206060 RIGGING PIN98DNSA20206120 RIGGING PIN and put the emergency control handle in the ARMED position.

NOTE: The 98DNSA20206120 RIGGING PIN is an alternative to the 98DNSA20206060 RIGGING PIN. But, because of its length, you cannot use the 98DNSA20206120 RIGGING PIN at all the location.

(17) Put the rod (9) in position and adjust its length if necessary.
(18) Install the washer (46), the bolt (48) and connect the rod (9).
(19) Install the washer (27) and the nut (26).
(20) TORQUE the nut (26) to between 0.35 and 0.3 m.daN (30.97 and 26.55 lbf.in )

NOTE: If you install a new bolt (48), drill a hole of 1.9 mm (0.0748 in.).

(21) Install the new AIPC 52-13-22-02-010 COTTER PIN (25).
(22) Remove the 98DNSA20206060 RIGGING PIN98DNSA20206120 RIGGING PIN.
(23) Install the rod (36) in position on the fitting (42).
(24) Install the washer (41), the bolt (40), the washer (37) and the nut (38).
(25) Tighten the nut (38).
(26) Install the new AIPC 52-13-22-02-010 COTTER PIN (39).
(27) Put the spring (33), the bush (34), the washers (35), the rod (36) and the fitting (42) in position on the rod (32).
(28) Install the bolts (44) and the nuts (43) on the fitting (42) and tighten them.
(29) Apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) by the grease fitting of the rod (32).

Subtask 52-13-22-420-055-A

G. Installation of the Escape Slide Control Mechanism

Escape Slide Control Mechanism

(1) Put the hook (198) and the spacer (184) in position.
(2) Apply a coat of Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) on the bolt (181).
(3) Install the washers (183), (182), (197) and the nut (196) and tighten it.

NOTE: If you install a new bolt (181) drill a hole of 2.8 mm (0.1102 in.).

(4) Install a new AIPC 52-13-11-10-010 COTTER PIN (195) or AIPC 52-13-84-12-010 COTTER PIN (195).
(5) Put the rod (180) in position and adjust it as follow:

Escape Slide Control Mechanism - Adjustment

(a) Put the emergency control handle in the DISARMED position.
(b) Install the washers (186), (192), the bolt (185) and the nut (194).
(c) Adjust the length of the rod (180) to get the clearance J1 of 2 +0 mm or +0.5 mm (0.0787 +0.0000 in. or +0.0197 in.) between the hook (198) and the emergency control handle.
(d) TORQUE the nut (194) to between 0.35 and 0.3 m.daN (30.97 and 26.55 lbf.in )

NOTE: If you install a new bolt (185), drill a hole of 1.9 mm (0.0748 in.).

(6) Install a new AIPC 52-13-11-10-010 COTTER PIN (193) or AIPC 52-13-84-12-010 COTTER PIN (193).
(7) Install the bushing (201) and the spring (200).
(8) Apply a coat of Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) on the axle of the rod end (199) and install it.
(9) Put the end rod (199) in position.
(10) Install the washers (188), (189), the bolt (187) and the nut (191).
(11) TORQUE the nut (191) to between 0.35 and 0.3 m.daN (30.97 and 26.55 lbf.in )

NOTE: If you install a new bolt (187), drill a hole of 1.9 mm (0.0748 in.).

(12) Install a new AIPC 52-13-11-10-010 COTTER PIN (190) or AIPC 52-13-84-12-010 COTTER PIN (190).

5. Close-up
Subtask 52-13-22-820-053-A

A. Adjustment
(1) Check the adjustment of the escape slide release mechanism (Ref. AMM TASK 52-13-22-820-001).
(2) Do an adjustment of the percussion bellcrank finger of the door damper and emergency operation cylinder (Ref. AMM TASK 52-13-14-820-002).
(3) Check the adjustment of the proximity switch 7WN1 or 7WN2 (Ref. AMM TASK 52-71-00-820-002).

Subtask 52-13-22-640-050-A

B. Lubrication
(1) Lubricate the ends of the girt bar with Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) .
(2) Lubricate the mating surfaces of the girt bar and the girt bar fittings with Silicone base Grease-General Purpose - - (Material No.03JBA1) .

Subtask 52-13-22-916-050-A

C. Protective Treatment
(1) Apply Primer Polyurethane Paint_- Corrosion Inhibiting Structure (Material No.04EAC2) to the ends of the screw threads and heads.
(2) Apply another coat of Top Coat Polyurethane_- Grey Internal Structure (Material No.04JME4) .
(3) Apply Non Hardening Jointing Putty-Medium Temp. Area - - (Material No.06LCG9) to the screws of the mechanism.
(4) Apply Corrosion Preventive Compound-Heavy Duty Soft Film - (Material No.12ACC1) to the metal parts which are not painted.
(5) Apply a coat of Corrosion Preventive Compound-Water Displacing Oily Film System (Material No.12ABE2) to all the parts installed.

Subtask 52-13-22-010-060-A ** ON A/C NOT FOR ALL

D. Installation of Components
(1) Install the door insulation.
(2) Install the door lining. (Ref. AMM TASK 25-23-46-400-002) 832FZ 832GZ 832EZ 832DZ 832CZ 832BZ 832AZ.
(3) Install the escape slide:
(a) For the left door:
Install the left-hand escape slide pack assembly (Ref. AMM TASK 25-62-44-400-006).
(b) For the right door:
Install the right-hand escape slide pack assembly (Ref. AMM TASK 25-62-44-400-802).

Subtask 52-13-22-010-060-B ** ON A/C NOT FOR ALL

D. Installation of Components
(1) Install the door insulation.
(2) Install the door lining (Ref. AMM TASK 25-23-46-400-002) 832FZ 832GZ 832EZ 832DZ 832CZ 832BZ 832AZ.
(3) Install the escape slide:
(a) For the left door:
Install the left-hand escape slide raft pack assembly (Ref. AMM TASK 25-62-44-400-007).
(b) For the right door:
Install the right-hand escape slide raft pack assembly (Ref. AMM TASK 25-62-44-400-803).

Subtask 52-13-22-865-052-A

E. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
121VU	EIS/SLIDES/ARM AND WARN/FLT	15WN	P11
121VU	EIS/SLIDES/ARM AND WARN/GND	13WN	P10
121VU	EIS/SDAC1 AND 2/DOOR/DET/PAX	48WV	P05

Subtask 52-13-22-010-061-A

F. Close Access
(1) Obey the special precautions after work on the door (Ref. AMM TASK 52-10-00-860-002).
(2) Remove all the ground support equipment, the maintenance equipment, the standard and special tools and all other items.
(3) Make sure that the work area is clean and clear of tools and other items.

Subtask 52-13-22-862-052-A

G. De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001).

[Rev.10 from 2021] 2026.04.02 07:21:54 UTC